Heat transfer study for thermal-hydraulic design of the solid-target of spallation neutron source

Journal of Nuclear Science and Technology

Volumn 38, Issue 10, 2001, Pages 832-843

  Tanaka, Futoshi ^a   Hibiki, Takashi ^a   Saito, Yasushi ^a   Takeda, Tomoaki ^b  

^a KYOTO UNIVERSITY   (Japan)

^b MITSUBISHI HEAVY INDUSTRIES LTD   (Japan)

Author keywords

Accelerators; Critical heat flux; Heat transfer; Horizontal flow; Multiphase flow; Rectangular duct; Solid target; Spallation neutron sources; Vertical upward flow

Indexed keywords

ATMOSPHERIC PRESSURE; CHANNEL FLOW; COMPUTER SIMULATION; COOLING; HEAT FLUX; HYDRAULICS; MULTIPHASE FLOW; NEUTRON SOURCES;

RECTANGULAR CHANNELS; SPALLATION NEUTRON SOURCE; SUBCOOLING; THERMAL HYDRAULIC DESIGN;

HEAT TRANSFER;

EID: 0035484397     PISSN: 00223131     EISSN: None     Source Type: Journal    
DOI: 10.1080/18811248.2001.9715103     Document Type: Article

References (17)

1. M. Holding, T. A. Broom, “The status of the ISIS targets,” Proc. 11th Int. Collaboration on Advanced Neutron Sources, 478(1991).
2. M. Furusaka, S. Ito, T. Otomo, Y. Kiyanagi, Preconceptual design of a target station in Neutron-Arena of JHF, KEK Report 96-4,(1996).
3. R. A. DeBortoli, S. J. Green, B. W. LeTourneau, M. Troy, A. Weiss, Forced-convection heat transfer burnout studies for water rectangular channels and round tubes at pressure above 500psia, WAPD-188, (1958).
4. Y. Sudo, K. Miyata, H. Ikawa, M. Kaminaga, M. Ohkawara, “Experimental study of differences in DNB heat flux between upflow and downflow in vertical rectangular channel,” J. Nucl. Sci. Technol., 22, 604 (1993).
5. K. Mishima, “Boiling burnout at low flow rate and low pressure conditions,” Ph. D. Thesis, Kyoto University, (1984).
6. K. Mishima, T. Hibiki, H. Nishihara, et al, “Experimental study on critical heat flux in laterally non-uniformly heated rectangular channels,” 2nd European Thermal-Sciences (EUROTHERM) & 14th UIT National Heat Transfer Conf., May 29-31,(1996).
7. F. W. Dittus, L. M. K. Boelter, “Heat transfer in automobile radiators of the tubular type,” Univ. Calif. Publs. Eng., 2, 443 (1930).
8. E. N. Sieder, G. E. Tate, “Heat transfer and pressure drop of liquids in tubes,”Ind. Eng. Chem., 28, 1429 (1936).
9. B. S. Petukhov, Adv Heat Transfer, 6, 521 (1970).
10. V. Gnielinski, “New equations for heat and mass transfer in turbulentpipe and channel flow,”Int. Chem. Eng., 16, 359 (1976).
11. W. H. McAdams, W. E. Kennel, C. S. L. Minden, et al., “Heat transfer at high rates to water with surface boiling,” Ind. Eng. Chem., 41, 1945 (1949).
12. W. H. Jens, P. A. Lottes, Analysis of heat transfer, burnout, pressure drop and density data for high-pressure water, ANL-4627,(1951).
13. R. S. Thom, “Boiling in sub-cooled water during flow up heated tubes or annuli,” Proc. Inst. Mech. Eng., 180, Pt 3C, 226 (1965).
14. J. C. Chen, “A correlation for boiling heat transfer to saturated fluids in convective flow,” ASME paper, 64-HT-34, (1964).
15. A. E. Bergles, W. M. Rohsenow, “The determination of forced-convection surface-boiling heat transfer,” ASME Ser C, 86,372 (1964).
16. L. Bernath, “A theory of local-boiling burnout and its application to existing data,” Chem. Eng. Prog. Symp. Ser, 56, 95 (1960).
17. W. R. Gambill, T. Mochizuki, “Advanced neutron source design: Burnout heat flux correlation development,” ANS/ENS 1988Int. Conf., 298 (1988).