Analysis of material transfer from a soft workpiece to a hard tool: Part ii-experimental verification of the proposed lump growth model

Journal of Tribology

Volumn 123, Issue 3, 2001, Pages 474-478

  De Rooij, M B ^a   Schipper, D J ^a  

^a UNIVERSITY OF TWENTE   (Netherlands)

Author keywords

[No Author keywords available]

Indexed keywords

ALUMINUM SHEET; DEEP DRAWING; METAL FORMING; SURFACE ROUGHNESS; ZINC;

MATERIAL TRANSFER;

WEAR OF MATERIALS;

LIFE ASSESSMENT; METAL WORKING; TOOL WEAR;

EID: 0035394154     PISSN: 07424787     EISSN: 15288897     Source Type: Journal    
DOI: 10.1115/1.1308023     Document Type: Article

References (15)

1. de Rooij, M. B., and Schipper, D. J., 2000, “Analysis of Material Transfer from a Soft Workpiece to a Hard Tool. Part I: Lump Growth Model,” ASME J. Tribol., 123, pp. 469-473.
2. Clarck, J. R., and Grant, M. B., 1992, “The Effect of Surface Finish on Component Performance,” Int. J. Mach. Tools Manuf., 32, pp. 183-193.
3. Schedin, E., and Lethinen, B., 1993, “Galling Mechanisms in Lubricated Systems: A Study of Sheet Metal Forming,” Wear, 170, pp. 119-130.
4. Schedin, E., 1994, “Galling Mechanisms in Sheet Forming Operations,” Wear, 179, pp. 123-128.
5. Roizard, X., and von Stebut, J., 1991, “Wear Debris Formation and Tool Transfer Build-up in Sheet Metal Forming,” Proc. 18th Leeds-Lyon Symposium on Tribology, D. Dowson, ed., Elsevier Science Publishers, Amsterdam, pp. 91-100.
6. Roizard, X., and von Stebut, J., 1990, “The Influence of Contact Temperature on Metal Transfer and Galling in Strip Drawing,” Proc. IDDRG Workgroup meeting, Borlange, IDDRG, pp. 1-8.
7. Stebut, J. V., Roizard, X., and Paintendre, B., 1989 “The Influence of Bulk Plastic Deformation on Die/Sheet Friction During Strip Drawing of Hot Dip Galvanized Sheets,” IDDRG WorkingGroup Meeting, Budapest, IDDRG, pp. 1-6.
8. Chen, L. H., and Rigney, D. A., 1990, “Adhesion Theories of Transfer and Wear During Sliding of Metals,” Wear, 136, pp. 223-235.
9. Bernick, L. M., Nilsen, R. R., and Wandrei, C. L., 1978, “Development of a Quantitative Sheet Galling Test,” Wear, 48, pp. 323-346.
10. Hirasaka, M., and Nishimura, H., 1994, “Effect of the Surface MicroGeometry of Steel Sheets on Galling Behavior,” J. Electron Microsc. Tech., 47, pp. 153-166.
11. ter Haar, R., 1996, “Friction in Sheet Metal Forming: The Influence of (Local) Contact Conditions and Deformation,” Ph.D. thesis, University of Twente, Enschede, the Netherlands.
12. Aspinwall, D. K., Wise, M. L. H., Stout, K. J., Goh, T. H. A., Zoa, F. L., and Menshawy, M. F., 1992, “Electrical Discharge Texturing,” Int. J. Mach. Tools Manuf., 32, pp. 183-193.
13. de Rooij, M. B., 1998, “Tribological Aspects of Unlubricated Deepdrawing Processes,” Ph.D. thesis, University of Twente, Enschede, the Netherlands.
14. Majumdar, A., and Bushan, B., 1991, “Fractal Model of Elastic-Plastic Contact Between Rough Surfaces,” J. Tribol., 113, pp. 1-11.
15. Saha, P., and Wilson, W., 1994, “Influence of Plastic Strain on Friction in Sheet Metal Forming,” Wear, 172, pp. 167-173.