Influence of inlet conditions on the thermohydrodynamic state of a fully circumferentially grooved journal bearing

Journal of Tribology

Volumn 123, Issue 3, 2001, Pages 525-532

  Keogh, P S ^a   Khonsari, M M ^b  

^a University of Bath   (United Kingdom)

^b LOUISIANA STATE UNIVERSITY   (United States)

Author keywords

[No Author keywords available]

Indexed keywords

HYDRODYNAMICS; PRESSURE DISTRIBUTION; TEMPERATURE DISTRIBUTION; THERMODYNAMIC PROPERTIES; VISCOSITY;

HYDRODYNAMIC BEARINGS; THERMOHYDRODYNAMICS;

JOURNAL BEARINGS;

DESIGN; JOURNAL BEARING; TEMPERATURE DISTRIBUTION; THERMOHYDRODYNAMIC LUBRICATION;

EID: 0035393252     PISSN: 07424787     EISSN: 15288897     Source Type: Journal    
DOI: 10.1115/1.1308029     Document Type: Article

References (17)

1. Pinkus, O., 1956, “Experimental Investigation of Resonant Whip,” ASME J. Appl. Mech., 78, pp. 975-983.
2. Newkirk, B. L., and Lewis, J. F., 1956, “Oil-Film Whirl-An Investigation of Disturbances due to Oil Films in Journal Bearings,” Trans. ASME, 78, pp. 21-27.
3. Akkok, M., and Ettles, C. M., 1978, “The Effect of Loading Intensity and Feed Pressure on the Whirl Stability of a Circumferentially Grooved Journal Bearing,”ASLE Paper 78-LC-6B-3.
4. Akkok, M., and Ettles, C. M., 1979, “The Effect of Grooving and Bore Shape on the Stability of Journal Bearings,” ASLE Paper 79-AM-6D-3.
5. Ettles, C. M., and Cameron, A., 1968, “Considerations of Flow Across a Bearing Groove,” ASME J. Lubr. Technol., 90, pp. 313-319.
6. Mitsui, J., Hori, Y., and Tanaka, M., 1983, “Thermohydrodynamic Analysis of Cooling Effect of Supply Oil in Circular Journal Bearing,” ASME J. Lubr. Technol., 105, pp. 414-421.
7. Heshmat, H., and Pinkus, O., 1986, “Mixing Inlet Temperatures in Hydrodynamic Bearings,” ASME J. Tribol., 108, pp. 231-248.
8. So, H., and Shieh, J. A., 1987, “The Cooling Effects of Supply Oil on Journal Bearings for Varying Inlet Conditions,” Tribol. Int., 20, pp. 79-89.
9. Ott, H. H., and Paradissiadis, G., 1988, “Thermohydrodynamic Analysis of Journal Bearings Considering Cavitation and Reverse Flow,” ASME J. Tri-bol., 110, pp. 439-447.
10. Roberts, J. B., and Mason, P. J., 1986, “An Experimental Investigation of Pressure Distributions in a Journal Bearing Operating in the Transition Regime,” J. Mech. Eng. Sci., 200, pp. 251-264.
11. Clayton, G. A., and Taylor, C. M., 1990, “Design Data for the Steadily Loaded Full Circumferentially Grooved Plain Journal Bearing,” J. Mech. Eng. Sci., 204, pp. 53-61.
12. Maki, E. R., and Ezzat, H. A., 1980, “Thermally Induced Whirl of a Rigid Rotor on Hydrodynamic Journal Bearings,” ASME J. Lubr. Technol., 102, pp. 8-14.
13. Dowson, D., 1962, “A Generalized Reynolds Equation for Fluid-Film Lubrication,” Int. J. Mech. Sci., 4, pp. 159-170.
14. Taylor, G. I., 1923, “Stability of a Viscous Liquid Contained Between Two Rotating Cylinders,” Trans. R. Soc. London, 223, pp. 289-343.
15. Kaye, J., and Elgar, E. C., 1958, “Modes of Adiabatic and Diabatic Fluid Flow in an Annulus with an Inner Rotating Cylinder,” Trans. ASME, 80, pp. 753-765.
16. Vohr, J. H., 1968, “An Experimental Study of Taylor Vortices and Turbulence in Flow Between Eccentric Cylinders,” ASME J. Lubr. Technol., 90, pp. 285-296.
17. Wendt, F., 1933, “Turbulente Stromungen Zwischen Zwei Rotierenden Konaxialen Zylindern,” Ingenieur-Archiv., 4, pp. 577-595.