Study: Temperature and residual stress in an injection moulded gear

Journal of Materials Processing Technology

Volumn 108, Issue 3, 2001, Pages 328-337

  Kansal, Gayatri ^a   Rao, P N ^b   Atreya, S K ^c  

^a INDIRA GANDHI NATIONAL OPEN UNIVERSITY   (India)

^b UNIVERSITI TEKNOLOGI MARA   (Malaysia)

^c INDIAN INSTITUTE OF TECHNOLOGY DELHI   (India)

Author keywords

[No Author keywords available]

Indexed keywords

COMPUTER AIDED DESIGN; COMPUTER AIDED MANUFACTURING; COOLING; INJECTION MOLDING; PLASTIC PRODUCTS; POLYSTYRENES; RESIDUAL STRESSES; SHRINKAGE; STRESS ANALYSIS; TEMPERATURE DISTRIBUTION; THERMAL STRESS; THERMOANALYSIS;

INJECTION MOLDED GEARS;

GEARS;

EID: 0035151571     PISSN: 09240136     EISSN: None     Source Type: Journal    
DOI: 10.1016/S0924-0136(00)00659-2     Document Type: Article

References (30)

1. Cheremininoff N.P. Emerging technologies and applications for polymers. Polym. Plast. Technol. Eng. 30(1):1991;1-26.
2. Litman A.M., Mohan C.R., Norman F.E. Selecting parts for computer aided engineering analysis. Polym. Plast. Technol. Eng. 26:1987;333-345.
3. G.G. Trantina, M.D. Minmichelli, T.W. Paro, Integrated analysis of plastic parts and mold stress, flow and heat transfer, in: Proceedings of the ASME International Computers in Engineering Conference and Exhibition, Boston, MA, 1985.
4. K. Schauer, Computer aided molded cooling design raises productivity, Plast. Technol. 63 (1983).
5. Kenig S., Kamal M.R. Cooling moulded parts - a rigorous analysis. SPE J. 26:1970;50-57.
6. Chang R.Y., Chiou S.Y. A unified K-BKZ model for residual stress analysis of injection moulded three-dimensional thin shapes. Polym. Eng. Sci. 35(22):1995;1733-1745.
7. Bushkoand W.C., Stokes V.K. Solidification of thermoviscoelastic melts. Part II. Effects of processing conditions on shrinkage and residual stresses. Polym. Eng. Sci. 35(4):1995;365-383.
8. N. Santhanam, Analysis of residual stresses and post-moulding deformation in injection moulded components, Ph.D. Thesis, Cornell University, Ithaca, NY, 1992.
9. Chang R.Y., Tsaur B.D. Experimental and theoretical studies of shrinkage warpage and sink marks of crystalline polymer injection moulded parts. Polym. Eng. Sci. 35:1995;1222-1230.
10. Chij Yu., Sunderland J.E. Determination of ejection temperature and cooling time in injection moulding. Polym. Eng. Sci. 32(3):1992;191-197.
11. Boldizar A., Josef K. Measurements of cycle time in injection molding of filled thermoplastics. Polym. Eng. Sci. 26(12):1986;877-885.
12. Agassant J.F., Alles H., Philipon S., Vincent M. Experimental and theoretical study of the injection molding of thermoplastic materials. Polym. Eng. Sci. 28(7):1988;460-468.
13. J.R. Saffell, A.H. Windle, The influence of thermal history on internal stress distributions in sheets of PMMA and polycarbonate, J. Appl. Polym. Sci. 25 (1980).
14. Coxon L.D., White J.R. Residual stresses and aging in injection molded polypropylone. Polym. Eng. Sci. 28(7):1988;460-468.
15. A. Siegmann, A. Buchman, S. Kenig, Residual stresses in polymers. 1. The effect of thermal history, Polym. Eng. Sci. 22 (L) (1982) 40-47.
16. Sandilands G.J., White J.R. Effect of injection pressure and crazing on internal stresses in injection molded polystyrene. Polymer. 21:1980;338-343.
17. J.R. Ockendon, W.R. Hodgkins, Moving Boundary Problems in Heat Flow and Diffusion, Oxford University Press, Oxford, 1975.
18. O.C. Zienkiewicz, The Finite Element Method in Engineering Science, McGraw-Hill, New York, 1971.
19. M.S.T. Jacques, An analysis of thermal warpage in injection moulded flat parts due to unbalanced cooling, Polym. Eng. II. Sci. 22 (4) (1982) 241-246.
20. Rigdahl M. Calculation of residual thermal stresses in injection moulded amorphous polymers by the finite element method. Int. J. Polym. Mater. 5:1976;43-57.
21. Mizikar E.A. Mathematical heat transfer model for solidification of continuously cast steel slabs. Trans. Metall. Soc. AIME. 239:1967;1747-1753.
22. Y. Sharir, A. Grill, J. Pelleg, Computation of Temperatures in Thin Tantatum Sheet Welding, Vol. 118, American Society for Metals, Cleveland, OH, Metallurgical Society of AIME, 1980, pp. 257-265.
23. O. Westby, Temperature distribution in the workplace by welding, A Report of Marine Technology Centre, University of Trondheim, Norway.
24. H.D. Brody, Needs and possibilities for process modelling research in process modelling, Proceedings of the American Society for Metals, 1980, pp. 27-55.
25. Sarjant R.J., Slack M.R. Internal temperature distribution in the cooling and reheating of steel ingots. J. Iron Steel Inst. 177:1954;428-444.
26. D.R. Croft, D.G. Lilley, Heat Transfer Calculations Using Finite Difference Equations, Applied Science Publishers, London, 1977.
27. Convery R.O., Miller P.P. Improved mould design by simulation of heat transfer. Plast. Rubber Int. 7(3):1982;138-141.
28. A. Mendelson, Plasticity: Theory and Application, Macmillan, New York (Chapters 9 and 10).
29. J.G Williams, Stress Analysis of Polymers, Ellis Horwood, Chichester, UK, 1973.
30. E. Buckingham, Analytical Mechanics of Gears, Dover, New York, 1963.