A study of non-recessed hybrid flexible journal bearing with different restrictors

Tribology Transactions

Volumn 44, Issue 2, 2001, Pages 310-317

  Sharma, Satish C ^a   Jain, S C ^a   Mohan Reddy, N Madhu ^a  

^a INDIAN INSTITUTE OF TECHNOLOGY ROORKEE   (India)

Author keywords

Journal bearing

Indexed keywords

BEARING; CHEMICAL AND PHYSICAL PROPERTIES; ELASTICITY; EQUIPMENT DESIGN; FILM; FINITE ELEMENT METHOD; FLUID FLOW; FRICTION; MATHEMATICAL ANALYSIS; PHYSICOCHEMICAL CONCEPTS;

DEFORMATION; ELASTICITY; FINITE ELEMENT METHOD; FLOW CONTROL;

ELASTIC DEFORMATION; RESTRICTORS;

JOURNAL BEARINGS;

FINITE ELEMENT ANALYSIS; FLUID FILM; JOURNAL BEARING; LUBRICANT; MATHEMATICAL ANALYSIS; PRESSURE;

BEARING; ELASTICITY; EQUIPMENT DESIGN; FILM; FINITE ELEMENT METHOD; FLUID FLOW; FRICTION; MATHEMATICAL ANALYSIS; PHYSICAL CHEMISTRY;

EID: 0034767699     PISSN: 10402004     EISSN: 1547397X     Source Type: Journal    
DOI: 10.1080/10402000108982464     Document Type: Article

References (21)

1. Rowe, W. B., Xu, S. X., Chong, F. S. and Weston, W., “Hybrid Journal Bearings with Particular Reference to Hole-Entry Configurations,” Trib. Intl., 15, 6, pp 339-348, (1982).
2. El Kayar, A., Salem, E. A., Khalil, M. F. and Hegazy, A. A., “Two-Dimensional Finite Difference Solution for Externally Journal Bearings of Finite Length,” Wear, 84, pp M3, (1983).
3. Yoshimoto, S., Rowe, W. B. and Ives, D. “A Theoretical Investigation of the Effect of Inlet Pocket Size on the Performance of Hole-Entry Journal Bearing Employing Capillary Restrictors,” Wear, 127, pp 307-318, (1988).
4. Palzewicz, A., “Hydrostatic Journal Bearing without Pressure Chambers Between Bearing Surface,” Wear, 159, pp 31-38, (1982).
5. Shangxian, and Xu, “Experimental Investigation of Hybrid Bearings,” Trib. Trans., 37, 2, pp 285-292, (1994).
6. Sharma, S. C., Sinhasan, R. and Jain, S. C, “An Elastohydrosiatic Study of Hole-Entry Hybrid Flexible Journal Bearings with Capillary Restrictors,” Trib. Inf. J., 26, 2, pp 93-107. (1993).
7. Jain, S. C., Sharma, S. C. and Nagraju, T., “Misaligned Journal Effects in Liquid Hydrostatic Non-recessed Journal Bearings,” Wear, 210, pp 67-75, (1997).
8. Shires, G. L. and Dee, C. W., “Pressurized Bearings with Inlet Slots,” in Proc. Of the Southampton Univ. Gas Bearing Symp., Paper 7, U.K., (1967).
9. Dee, C. W. and Shires, G. L., “The Current State of the Art of Fluid Bearings with Discrete Slot Inlets,” Trans. ASME, Jr. Of Lubr Tech., 93, 2, pp 441-450, (1974).
10. Stout, K. J. and Rowe, W. B. “Externally Pressurized Bearings - Design for Manufacture, Part 1- Journal Bearing Selection,” Trib. Intl., 7, 3., pp 98-106, (1974).
11. Stout, K. J. and Rowe, W. B., “Externally Pressurized Bearings - Design for Manufacture, Part 3- Design of Liquid Externally Pressurized Bearings for Manufacture Including Tolerencing Procedure,” Trib., Intl., 4, 5, pp 195-212, (1974).
12. Rowe, W. B., Koshal, D. and Stout, K. J., “Slot-Entry Bearings for Hybrid Hydrodynamic and Hydrostatic Operation,” Jour, of Mech. Eng. Science, 18, 2, pp 73-78, (1976).
13. Rowe, W. B., Kosha, D. and Stout, K. J., “Investigation of Recessed Hydrostatic and Slot-Entry, Journal Bearings for Hybrid Hydrodynamic and Hydrostatic Operation,” Wear, 43, pp 55-69, (1977).
14. Koshal, D. and Rowe, W. B., “Fluid Film Journal Bearings Operating in a Hybrid Mode, Part I - Theoretical Analysis and Design,” Trans. ASME, Jour, of Lubr. Tech., 103, pp 558-568, (1981).
15. Koshal, D. and Rowe, W. B., “Fluid Film Journal Bearings Operating in a Hybrid Mode, Part II - Experimental Investigation,” Trans. ASME, Jour: of Lubr. Tech., 103, pp 566-572, (1981).
16. Vermeulen, M., “Pressure Cut-Off Behavior of a Hybrid Slot-Entry Pivoting Pad,” in Proc. Of IMechE, Triboiogy-Friction, Lubrication and Wear, C 186, pp 129-141,(1987).
17. Ives, D. and Rowe, W. B., “The Effect of Multiple Sources on Performance of Heavily Loaded Pressurized High Speed Journal Bearings,” in Proc. IMechE Trib. Friction, Lubr: and Wear, C 199, pp 121-128, (1987).
18. Ives, D. and Rowe, W. B., “The Performance of Hybrid Journal Bearings in the Superiaminar Flow Regimes,” Trib. Trans., 35, 4, pp 627-632, (1992).
19. Cheng, K. and Rowe, W. B., “A Selection Strategy for the Design of Externally Pressurized Journal Bearings,” Trib., Intl., 28, 7, pp 465-474, (1995).
20. Sharma, S. C., Kumar, V., Jain, S. C, Sinhasan, R. and Subramanian, M., “A Study of Slot-Entry Hydrostatic/Hybrid Journal Bearing Using the Finite Element Method,” Trib., Intl., 32, 4, pp 185-196, (1999).
21. Rowe, W. B., “Hydrostatic and Hybrid Bearing Design,” Butterworths, London, (1983).