Sine sweep load vs. impact excitations and their influence on the damping coefficients of a bubbly oil squeeze film damper

Tribology Transactions

Volumn 44, Issue 4, 2001, Pages 692-698

  San Andrés, Luis ^a   Diaz, Sergio E ^b   Rodriguez, Luis E ^b  

^a TEXAS A AND M UNIVERSITY   (United States)

^b UNIVERSIDAD SIMÓN BOLÍVAR   (Venezuela)

Author keywords

Bubbly flows; Rotor dynamics; Squeeze film dampers

Indexed keywords

AIR ENTRAINMENT; COALESCENCE; DAMPING; DYNAMIC RESPONSE; IMPACT TESTING; VIBRATION CONTROL; VISCOSITY;

SQUEEZE FILM DAMPERS (SFD);

LUBRICATING OILS;

BUBBLY FLOW; DAMPER; LUBRICATION; SQUEEZE FILM; TURBOMACHINERY;

EID: 0034762036     PISSN: 10402004     EISSN: 1547397X     Source Type: Journal    
DOI: 10.1080/10402000108982512     Document Type: Article

References (13)

1. Beets, T. A., Díaz, S. E. And San Andrés, L. A. (2000), “Pressure Measurement and Flow Visualization on a SFD With a Bubbly Lubricant,” in Proc. Of the 2000 NSF Design and Manufacturing Research Conf., NSF, Washington, DC.
2. Coleman, H. W. And Steele, W. G. (1989), “Experimentation and Uncertainty Analysis for Engineers,” John Wiley and Sons Pubs, New York, NY.
3. Diaz, S. E. And San Andrés, L. A. (1999a), “Reduction of the Dynamic Load Capacity in a Squeeze Film Damper Operating with a Bubbly Lubricant,” ASME Jour, of Gas Turbines and Power, 121, pp 703-709.
4. Diaz, S. E. And San Andrés, L. A. (1999b), “Air Entrainment vs. Lubricant Vaporization in Squeeze Film Dampers: An Experimental Assessment of the Fundamental Differences,” ASME Paper 99-GT-187, ASME, New York, NY.
5. Diaz, S. E. And San Andrés, L. A. (1999c), “A Method for Identification of Bearing Force Coefficients and Its Application to a Squeeze Film Damper with a Bubbly Lubricant,” Trib. Trans., 42, 4, pp 739-746.
6. Edney, S. L. And Nicholas, J. C. (1999), “Retrofitting a Large Steam Turbine with a Mechanically Centered Squeeze Film Damper,” in Proc. Of the 28th Turbomachinery Symp., Texas A&M University, College Station, TX, pp 29-40.
7. Fritzen, C. (1986), “Identification of Mass, Damping and Stiffness Matrices of Mechanical Systems,” Jour, of Vibration, Acoustics. Stress and Reliability in Design, 108, 1, pp 9-16.
8. Mitchell, L. D. And Elliot, K. B. (1984), “How to Design Stingers for Vibration Testing of Structures,” Sound and Vibration, 18, 4, pp 14-18.
9. San Andrés, L. And Vance, J. (1987), “Force Coefficients for Open Ends Squeeze Film Dampers Executing Small Amplitude Motions About an Off-Centered Equilibrium Position,” ASLE Trans., 30, 1, pp 63-68.
10. Tao, L., Diaz, S. E., San Andrés, L. A. And Rajagopal, K. R. (2000), “Analysis of Squeeze Film Dampers Operating with Bubbly Lubricants,” ASME Jour, of Trib., 122, 1, pp 205-210.
11. Vance, J. (1988), Rotordynamics of Turbomachinery, John Wiley and Sons Pubs., NY.
12. Zeidan, F. Y. And Vance, J. M. (1990), “Cavitation Regimes in Squeeze Film Dampers and Their Effect on the Pressure Distribution,” Trib. Trans., 33, pp 447-453.
13. Zeidan, F. Y., San Andrés, L. A., and Vance, J. M. (1996), “Design and Application of Squeeze Film Dampers in Rotating Machinery,” in Proc. Of the 25th Turbomachinery Symp., Texas A&M University, College Station, TX, pp 169-188.