Inertial, viscous and yield stress effects in Bingham fluid filling of a 2-D cavity

Journal of Non-Newtonian Fluid Mechanics

Volumn 96, Issue 3, 2001, Pages 383-403

  Alexandrou, Andreas N ^a   Duc, Emmanuel ^a   Entov, Vladimir ^b  

^a WORCESTER POLYTECHNIC INSTITUTE   (United States)

^b INSTITUTE FOR PROBLEMS IN MECHANICS   (Russian Federation)

Author keywords

[No Author keywords available]

Indexed keywords

BUBBLE FORMATION; INJECTION MOLDING; REYNOLDS NUMBER; TRANSITION FLOW; VISCOUS FLOW; YIELD STRESS;

BINGHAM FLUIDS;

NON NEWTONIAN FLOW;

BINGHAM FLUID; CAVITY; FILLER; INERTIA; INJECTION MOLDING; VISCOUS FLOW; YIELD STRESS;

EID: 0034744772     PISSN: 03770257     EISSN: None     Source Type: Journal    
DOI: 10.1016/S0377-0257(00)00199-3     Document Type: Article

References (26)

1. Injection Molding Handbook: The Complete Molding Operation: Technology, Performance, Economics, Van Nostrand Reinhold, New York, 1986.
2. D.M. Bryce, Plastic injection molding manufacturing process fundamentals, Vol. 1: fundamentals of injection molding series, Dearborn Michigan, Soc. Manuf. Eng. (1996).
3. G.H. Convey, B.R. Stanmore, Use of parallel-plate plastometer for the characterization of viscous fluids with yield stress, J. Non-Newtonian Fluid Mech. 8 (1981) 249.
4. R.E. Carter, R.C. Warren, Extrusion stresses die swell and viscous heating effects in double-base propellants, J. Rheol. 31 (1987) 151-173.
5. N.P. Cheremisinoff, An Introduction to Polymer Rheology and Processing, Elastomers Technology Division, Exxon Chemical Company, Linden, NJ, 1993.
6. H.A. Barnes, K. Walters, The yield stress myth? Rheol. Acta 24 (1985) 323-326.
7. J.P. Hartnett, R.Y.Z. Hu, Technical note: The yield stress: an engineering reality, J. Rheol. 33 (1989) 671-679.
8. G.R. Burgos, A.N. Alexandrou, V.M. Entov, Time-dependent rheology of semisolid metal suspensions, Synthesis of light metals III, in: F.H. Froes, C.M. Ward-Close, P.G. McCormick, D. Eliezer (Eds.), Proceedings of the Symposium sponsored by the LMD and SMD divisions of the TMS, San Diego, CA, 1999.
9. E.G. Bingham, Fluidity and Plasticity, McGraw-Hill, New York, 1922.
10. J.G. Oldroyd, A rational formulation of the equations of plastic flow for a Bingham solid, Proc. Camb. Philos. Soc. 15 (1984) 75-83.
11. R.B. Bird, G.C. Dai, B.J. Yaruso, The rheology and flow of viscoplastic materials, Rev. Chem. Eng. 1 (1983) 1-70.
12. A.N. Alexandrou, A. Ahmed, Injection molding using generalized Eulerian Lagrangian approach, Pol. Eng. Sci. 33 (16) (1984) 1055-1069.
13. R.-Y. Chang, S.-Y. Chiou, Integral constitutive model (K-BKZ) to describe viscoelastic flow in injection molding, J. Polym. Proc. Soc. 9 (4) (1994) 365.
14. G. Titomanlio, V. Speranza, V. Brucato, On the simulation of thermoplastic injection moulding process, J. Polym. Proc. Soc. 10 (1) (1995).
15. M. Fujiyama, Stuctures and properties of injection moldings of β-crystal nucleator-added polypropylenes. Part 1, J. Polym. Proc. Soc. 10 (2) 1995.
16. F. Bardinet, A.N. Alexandrou, Thixo-module development for simulor, Pechiney Internal Report, 1998.
17. M. Bercovier, M. Engelman, A finite element method for incompressible non-Newtonian flows, J. Comput. Phys. 36 (1980) 313-326.
18. E.J. O'Donovan, R.I. Tanner, Numerical study of the Bingham squeeze film problem, J. Non-Newtonian Fluid Mech. 15 (1984) 75-83.
19. T.C. Papanastasiou, Flows of materials with yield, J. Rheol. 31 (1987) 385-404.
20. A.N. Beris, J.A. Tsamopoulos, R.A. Brown, R.C. Armstrong, Creeping flow around a sphere in a Bimgham plastic, J. Fluid Mech. 158 (1985) 219-244.
21. E. Mitsoulis, S.S. Abdali, N.C. Markatos, Flow simulation of Herschel-Bulkley fluids through extrusion dies, Can. J. Chem. Eng. 71 (1993) 147-160.
22. G. Burgos, A.N. Alexandrou, V.M. Entov, On the determination of yield surfaces in Herschel-Bulkley fluids, J. Rheol. 43 (3) (1999) 463-483.
23. G. Burgos, A.N. Alexandrou, Flow development of Herschel-Bulkley fluids in a sudden 3-D square expansion, J. Rheol. 43 (3) (1999) 485-498.
24. C. Rigaut, B. Janin, P. Laty, A. Bourg, A. Latrobe, SIMULOR Un logiciel de modilisation 3D du remplissage et de la solidification en moulage, Aluminium Pechiney 38 Voreppe, 1989.
25. F. Bardinet, A.N. Alexandrou, W. Loue, Numerical simulation of die filling in semisolid metal processing, Light Metals TMS 97 (1997) 945-951.
26. C.J. Paradies, M. Rappaz, Modeling the rheology of semi-solid metal alloys during die casting, Modeling of Casting Welding and Advanced Solidification Processes TMS 8 (1988) 933-940.