Changes of surface topography during wear for surfaces with different height distributions

Tribology Transactions

Volumn 43, Issue 4, 2000, Pages 749-757

  Jeng, Yeau Ren ^a   Gao, Chih Chung ^a  

^a NATIONAL CHUNG CHENG UNIVERSITY   (Taiwan)

Author keywords

Heigh distribution; Running in; Surface topography; Wear

Indexed keywords

GRINDING (COMMINUTION); MATHEMATICAL MODELS; MICROMACHINING; PARTICLE SIZE ANALYSIS; POLISHING; SURFACE TOPOGRAPHY;

SURFACE HEIGHT DISTRIBUTION;

WEAR OF MATERIALS;

RUNNING IN; SURFACE ROUGHNESS; TOPOGRAPHY; WEAR;

EID: 0034306531     PISSN: 10402004     EISSN: 1547397X     Source Type: Journal    
DOI: 10.1080/10402000008982404     Document Type: Article

References (22)

1. Thomas, T. R., "Computer Simulation of Wear," Wear, 22, pp 83-90, (1972).
2. Soda, N. "Wear of Some F.C.C Metals during Unlubricatcd Sliding Part II: Effects of Normal Load, Sliding, Velocity and Atmospherical Pressure on Wear Fragments," Wear, 35, pp 331-343, (1975).
3. Golden, J. M., "The Evolution of Asperity Height Distributions of a Surface Subjected to Wear," Wear, 39, pp 25-44, (1976).
4. King, T. G., Watson, W. and Stout, K. J., "Modeling the Micro-Geometry of Lubricated Wear," in Proc. of 4th Leeds/Lyon Symp. on Trib. in Surface Roughness Effects in Lubrication, Dowson, D., Godet, M. and Taylor, C., Eds., Mechanical Engineering Publications, London, (1977).
5. Slout, K. J., King, T. G. and Watson, W., "Topography of Running in of Plain Bearings," Mecanique, Materiaux. Electricite, 337, pp 45-52, (1978).
6. Spedding, T. A., King, T. G., Watson, W. and Stout, K. J., "The Pearson System of Distribution: Its Application to Non-Gaussian Surface Metrology and A Simple Wear Model," Jour, of Lubr. Tech., ASME, 102, pp 495-500, (1980).
7. Jacobson, S., Wallen, P. and Hogmark, S., "Correlation between Groove Size, Wear Rate, and Topography of Abraded Surfaces," Wear, 115, pp 83-93, (1987).
8. Jacobson, S., Wallen, P. and Hogmark, S., "Fundamental Aspects of Abrasive Wear Studied by A New Numerical Simulation Model/' Wear, 123, pp 207-223, (1988).
9. Zhang, B. and Xie, Y. B., "Two-Body Microcutting Wear Model Part I: Two Dimensional Roughness Model," Wear, 129, pp 37-48, (1989).
10. Zhang, B. and Xie, Y. B., 'Two-Body Microcutting Wear Model Part II: Three-Dimensional Roughness Model," Wear, 129, pp 49-58, (1989).
11. Sugimura, J., Kimura, Y. and Amino, K., "Analysis of The Topography Changes Due to Wear-Geometry of The Running-in Process," JSLE, 31, 2, pp 813-820,(1986).
12. Kimura, Y. and Sugimura, J., "Microgeometry of Sliding Surfaces and Wear Panicles in Lubricated Contact," Wear, 100, pp 33-45, (1984).
13. Dunaevsky, V. V., "Measurement of Local Microscopic Wear," Jour, of Trib., ASME, 108, pp 35-41, (1986).
14. Lin, J. Y. and Cheng, H. S., "An Analytical Model for Dynamic Wear," Jour. of Trib., ASME, 111, pp 468-474, (1989).
15. Sugimura, J, and Kimura, Y., "Characterization of Topographical Changes During Lubricated Wear," Wear, 98. pp 101-116, (1984).
16. Hu, Y. Z., Na, L. and Tonder, K., "Dynamic System Model for Lubricated Sliding Wear and Running-in," Jour. of Trib., Trans, of the ASME, 113, 3, pp 499-505,(1991).
17. Kapoor, A. J., Williams, A. and Johnson, K. L., "The Steady State Sliding of Rough Surfaces," Wear, 175, pp 81-92, (1994).
18. Jeng, Y. R., "Impact of Plateaued Surfaces on Tribologicat Performance," Trib. Trans., 39, 1. pp 354-361,(1996).
19. Johnson, N. L., "Systems of Frequency Curves Generated by Methods of Translation," Biometrika, 36, pp 149-176, (1949).
20. Elderton, W. P. and Johnson, N. L., "Systems of Frequency Curves," Cambridge University Press. (1969).
21. Jeng, Y. R., "Characterization of Surface Height Distributions." Jour, of the Chinese Soc. of Mech. Eng., 19, 4, pp 417-423, (1998).
22. Jeng, Y. R. and Gao, C. C., "Effects of Wear Particles on Topographical Changes during Sliding Wear," in Proc. of Herbert S. Cheng Symp., STLEIASME Trib. Conf, (1999).