Effect of two-scale roughness on boundary layer transition over a heated flat plate: Part 1 - surface heat transfer

Journal of Turbomachinery

Volumn 122, Issue 2, 2000, Pages 301-307

  Pinson, Mark W ^a,b   Wang, Ting ^a,c  

^a AMRL   (United States)

^b GENERAL ELECTRIC COMPANY   (United States)

^c UNIVERSITY OF NEW ORLEANS   (United States)

Author keywords

[No Author keywords available]

Indexed keywords

BOUNDARY LAYER FLOW; SURFACE ROUGHNESS; TRANSITION FLOW;

HEATED FLAT PLATE;

HEAT TRANSFER;

BOUNDARY LAYER; HEAT TRANSFER; PLATE; ROUGHNESS; SURFACE ROUGHNESS;

EID: 0034177667     PISSN: 0889504X     EISSN: None     Source Type: Journal    
DOI: 10.1115/1.555448     Document Type: Conference Paper

References (32)

1. Hodson, H. P., Huntsman, I., and Steele, A. B., 1994, "An Investigation of Boundary Layer Development in a Multistage LP Turbine," ASME J. Turbomach., 116, pp. 375-383.
2. Halstead, D. E., Wisler, D. C., Okiishi, T. H., Walker, G. J., Hodson, H. P., and Shin, H.-W., 1997, "Boundary Layer Development in Axial Compressors and Turbines: Part 1 of 4 - Composite Picture," ASME J. Turbomach., 119, pp. 114-127.
3. Kleiser, L., and Zang, T. A., 1991, "Numerical Simulation of Transition in Wall-Bounded Shear Flows," Annu. Rev. Fluid Mech., 23, pp. 495-537.
4. Tarada, F. H. A., 1987, "Heat Transfer to Rough Turbine Blading," Ph.D. dissertation, University of Sussex, England.
5. Taylor, R. P., 1990, "Surface Roughness Measurements on Gas Turbine Blade," ASME J. Turbomach., 112, pp. 175-180.
6. Bammert, K., and Sandstede, H., 1972, "Measurements Concerning the Influence of Surface Roughness and Profile Changes on the Performance of Gas Turbines," ASME J. Eng. Power, 94, pp. 207-213.
7. Bammert, K., and Sandstede, H., 1980, "Measurements of the Boundary Layer Development along a Turbine Blade With Rough Surfaces," ASME J. Eng. Power, 102, pp. 978-983.
8. Boynton, J. L., Tabibzadeh, R., and Hudson, S., 1993, "Investigation of Rotor Blade Roughness Effects on Turbine Performance," ASME J. Turbomach., 115, pp. 614-620.
9. Suder, K. L., Chima, R. V., Strazisar, A., and Roberts, W., 1995, "The Effect of Adding Roughness and Thickness to a Transonic Axial Compressor Rotor," ASME J. Turbomach., 117, pp. 491-505.
10. Blair, M. F., 1994, "An Experimental Study of Heat Transfer in a Large-Scale Turbine Rotor Passsage," ASME J. Turbomach., 116, pp. 1-13.
11. Tarada, F., and Suzuki, M., 1993, "External Heat Transfer Enhancement to Turbine Blading Due to Surface Roughness," ASME Paper No. 93-GT-74.
12. Bunker, R. S., 1997, "Separate and Combined Effects of Surface Roughness and Turbulence Intensity on Vane Heat Transfer," ASME Paper No. 97-GT-135.
13. Nikuradse, J., 1933, "Stomungsgesetz in Rahen Rohren," Forschg. Arb. Ing.-Wes., 361 (English Trans. NACA Tech. Memo 1292).
14. Nikuradse, J., 1933, "Stomungsgesetz in Rahen Rohren," Forschg. Arb. Ing.-Wes., 361 (English Trans. NACA Tech. Memo 1292).
15. Schlichting, H., 1936, "Experimentelle Untersuchungen zum Rauhigkeitsproblem," Ingeniour-Archiv, 7, pp. 1-34 (English Trans. NACA Tech. Memo 823).
16. Schlichting, H., 1936, "Experimentelle Untersuchungen zum Rauhigkeitsproblem," Ingeniour-Archiv, 7, pp. 1-34 (English Trans. NACA Tech. Memo 823).
17. Coleman, H. W., Hodge, B. K., and Taylor, R., 1984, "A Re-Evaluation of Schlichting's Surface Roughness Experiment," ASME J. Fluids Eng., 106, pp. 60-65.
18. Simpson, R. L., 1973, "A Generalized Correlation of Roughness Density Effects on the Turbulent Boundary Layer," AIAA J., 11, pp. 242-244.
19. Sigal, A., and Danberg, J. E., 1990, "New Correlation of Roughness Density Effect on the Turbulent Boundary Layer," AIAA J., 28, pp. 554-556.
20. Doenhoff, A. E. V., and Horton E. A., 1958, "A Low-Speed Experimental Investigation of the Effect of a Sandpaper Type of Roughness on Boundary-Layer Transition," NACA Report 1349.
21. Pinson, M. W., and Wang, T., 1997, "Effects of Leading-Edge Roughness on Fluid Flow and Heat Transfer in the Transitional Boundary Layer Over a Flat Plate," Int. J. Heat Mass Transf., 40, pp. 2813-2823.
22. Gibbings, J. C., and Al-Shukri, S. M., 1997, "Effect of Sandpaper Roughness and Stream Turbulence on the Laminar Layer and Its Transition," Aeronaut. J., 101, pp. 17-24.
23. Ligrani, P. M., and Moffat, R. J., 1985, "Thermal Boundary Layers on a Rough Surface Downstream of Steps in Wall Temperature," Boundary-Layer Meteorol., 31, pp. 127-147.
24. Bogard, D. G., Schmidt, D. L., and Tabbita, M., 1998, "Characterization and Laboratory Simulation of Turbine Airfoil Surface Roughness and Associated Heat Transfer," ASME J. Turbomach., 120, pp. 337-342.
25. Pinson, M., 1998, "Effect of Two-Scale Roughness on Boundary Layer Transition Over a Heated Flat Plate," Ph.D. Dissertation, Department of Mechanical Engineering, Clemson University, Clemson, SC.
26. Zhou, D., and Wang, T., 1996, "Combined Effects of Elevated Free-Stream Turbulence and Streamwise Acceleration on Flow and Thermal Structures in Transitional Boundary Layers," Exp. Therm. Fluid Sci., 12, pp. 338-351.
27. Shome, B., 1991, "Development of a Three-Wire Probe for the Measurement of Reynolds Stresses and Heat Fluxes in Transitional Boundary Layers," M.S. Thesis, Department of Mechanical Engineering, Clemson University, Clemson, SC.
28. Kays, W. M., and Crawford, M. E., 1993, Convective Heat and Mass Transfer, 3rd ed. McGraw-Hill, pp. 175, 179, 181.
29. Acarlar, M. S., and Smith, C. R., 1987, "A Study of Hairpin Vortices in a Laminar Boundary Layer. Part 1, Hairpin Vortices Generated by a Hemisphere Protuberance," J. Fluid Mech., 175, pp. 1-41.
30. Ruderich, R., and Fernholz, H. H., 1986, "An Experimental Investigation of a Turbulent Shear Flow With Separation, Reverse Flow, and Reattachment," J. Fluid Mech., 163, pp. 283-322.
31. Eaton, J. K., and Johnston, J. P., 1981, "A Review of Research on Subsonic Turbulent Flow Reattachment," AIAA J., 19, pp. 1093-1100.
32. Braslow, A. L., 1960, "Review of the Effect of Distributed Surface Roughness on Boundary-Layer Transition," Advisory Group for Aeronautical Research and Development, Report 254.