Mist/steam cooling in a heated horizontal tube-Part 1: Experimental system

Journal of Turbomachinery

Volumn 122, Issue 2, 2000, Pages 360-365

  Guo, Tao ^a,b   Wang, Ting ^a,c   Gaddis, J Leo ^a  

^a AMRL   (United States)

^b GE ENERGY   (United States)

^c UNO College of Engineering   (United States)

Author keywords

[No Author keywords available]

Indexed keywords

ATOMIZERS; FOG; PIPE FLOW; REYNOLDS NUMBER; STEAM;

ADVANCED TURBINE SYSTEMS (ATS); PHASE DOPPLER PARTICLE ANALYZER (PDPA) SYSTEM;

COOLING;

COOLING; GAS TURBINE; HEAT TRANSFER; STEAM;

EID: 0034176408     PISSN: 0889504X     EISSN: None     Source Type: Journal    
DOI: 10.1115/1.555460     Document Type: Conference Paper

References (18)

1. Van der Lindea, S., 1992, "Advanced Turbine Design Program," in: Proc. Ninth Annual Coal-Fueled Heat Engines, Advanced Pressurized Fluid-Bed Combustion (PFBC), and Gas Stream Cleanup Systems Contractors Reviewing Meeting, Oct. 27-29, Morgantown, WV, pp. 215-227.
2. Bannister, R. L., and Little, D. A., 1993, "Development of Advanced Gas Turbine System," in: Proc: Joint Contractor Meeting: FE/EE Advanced Turbine System Conference; FE Fuel Cells and Coal-Fired Heat Engine Conference, Aug. 3-5, Morgantown, WV, pp. 3-15.
3. Mukavetz, D. W., Wenglarz, R., Nirmalan, N., and Daehler, T., 1994, "Advanced Turbine System (ATS) Turbine Modification for Coal and Biomass Fuels," in: Proc. of the Advanced Turbine System Annual Program Review Meeting, Nov. 9-11, ORNL/Arlington, VA, pp. 91-95.
4. Bannister, R. L., Cheruvu, N. S., Little, D. A., and McQuiggan, G., 1995, "Development Requirements for an Advanced Gas Turbine System," ASME J. Turbomach., 117, pp. 724-733.
5. Farmer, R., and Fulton, K., 1995, "Design 60%, Net Efficiency in Frame 7/9H Steam-Cooled CCGT," Gas Turbine World, May-Jun, pp. 12-20.
6. Mukherjee, D., 1984, "Combined Gas Turbine and Steam Turbine Power Station," Patented by ABB, U.S. Patent No. 4424668.
7. Alff, R. K., Manning, G. B., and Sheldon, R. C., 1978, "The High Temperature Water Cooled Gas Turbine in Combined Cycle With Integrated Low BTU Gasification," Combustion, 49, pp. 27-34.
8. Chen, J. C., and Costigan, 1992, "Review of Post-Dryout Heat Transfer in Dispersed Two Phase Flow," Post-Dryout Heat Transfer, Hewitt, G. F., et al. eds., CRC Press, Inc., FL, pp. 1-37.
9. Guo, T., Wang, T., and Gaddis. J., 1999, "Mist/Steam Cooling in a 180-Degree Tube," presented at the National Heat Transfer Conference, Albuquerque, NM, Aug. 14-17.
10. Guo, T., 1998, "Mist/Steam Cooling in a Heated Horizontal Tube," Ph.D Dissertation, Mechanical Engineering Department, Clemson University, Clemson, SC.
11. Mori, Y., Hijikata, K., and Yasunaga, T., 1982, "Mist Cooling of Very Hot Tubules With Reference to Through-Hole Cooling of Gas Turbine Blades," Int. J. Heat Mass Transf., 25, No. 9, pp. 1271-1278.
12. Janssen, J. M., Florschuetz, L. W., and Fizdon, J. P., 1986, "Heat Transfer to Two-Phase Air/Water Mixtures Flowing in Small Tubes With Inlet Disequilibrium," NASA CR 175076.
13. Swithenbank, J., Cao, J., and Hamidi, A. A., 1991, Spray Diagnostics by Laser Diffraction Combustion Measurement, Chigier, N., ed., Hemisphere Publishing Co.
14. Bachalo, W. D., 1980, "Method for Measuring the Size and Velocity of Spheres by Dual-Beam Light Scatter Interferometry," Appl. Opt., 19, No. 3, pp. 363-372.
15. Bachalo, W. D., and Houser, M. J., 1984, "Phase Doppler Spray Analyzer for Simultaneous Measurements of Drop Size and Velocity Distributions," Opt. Eng. (Bellingham), 23, No. 5, pp. 583-597.
16. Kline, S. J., 1985, "The Purposes of Uncertainty Analysis," ASME J. Fluids Eng., 107, pp. 153-160.
17. Moffat, R. J., 1985, "Using Uncertainty Analysis in the Planning of an Experiment," ASME J. Fluids Eng., 107, pp. 173-178.
18. Wang, T., and Simon, T. W., 1989, "Development of a Special-Purpose Test Surface Guided by Uncertainty Analysis," J. Thermophys. Heat Transfer, 3, No. 1, pp. 19-26.