Modelling requirements for computer simulation of metal machining

Turkish Journal of Engineering and Environmental Sciences

Volumn 24, Issue 2, 2000, Pages 81-93

  Dirikolu, M Hüsnü ^a   Childs, Thomas H C ^b  

^a KIRIKKALE UNIVERSITY   (Turkey)

^b UNIVERSITY OF LEEDS   (United Kingdom)

Author keywords

Chip separation; Flow characteristics; Friction characteristics; Machining; Simulation

Indexed keywords

COMPUTER MODELING; METAL WORKING;

EID: 0033868517     PISSN: 13000160     EISSN: None     Source Type: Journal    
DOI: None     Document Type: Article

References (42)

1. ASM Metals Handbook 9th ed., 1979.
2. Bailey, J. A., "Friction in Metal Machining-Mechanical Aspects", Wear, 31, 243-275, 1975.
3. Baird, J. D., "Strain Aging of Steel-A Critical Review", Iron and Steel, 36, 450-457, 1963.
4. Bathe, K-J., Finite Element Procedures, Prentice Hall, 1996.
5. Boothroyd, G., "Temperatures in Orthogonal Metal Cutting", Proc. I.Mech.E, 177, No.29, p.789, 1963.
6. Bridgman, P. W., Studies in Large Plastic Flow and Fracture with Special Emphasis on the Effects of Hydrostatic Pressure, McGraw-Hill, New York, 1952.
7. Carroll, J. T. and Strenkowski, S. J., "Finite Element Models of Orthogonal Cutting with Application to Single Point Diamond Turning", Int. J. Mech. Sci., 30, 899-920, 1988.
8. Childs, T. H. C. and Maekawa, K., "Computer Aided Simulation and Experimental Studies of Chip Flow and Tool Wear in the Turning of Low Alloy Steels by Cemented Carbide Tools", Wear , 139 , pp235-250, 1990.
9. Childs, T. H. C. and Rowe, G. W., Physics of Metal Cutting, Rep. Prog. Phys., 36, p.223, 1973.
10. Childs, T. H. C., "Contact Stresses in Metal Cutting", IOP Short Meetings, Ser. 25, 49-62, 1990.
11. Childs, T. H. C., Dirikolu, M. H., and Maekawa, K., "Modelling of Friction in the Simulation of Metal Machining", 24th Leeds-Lyon Symposium on Tribology, Tribology for Energy Conservation, Part of World Tribology Conference, London-England, 4-6 September, 1997a.
12. Childs, T. H. C., Dirikolu, M. H., Sammons, M. D. S., Maekawa, K., and Kitagawa, T., "Experiments on and Finite Element Modelling of Turning Free-Cutting Steels at Cutting Speeds up to 250 m/min.", Proc. 1st French and German Conf. on High Speed Machining (HSM), Metz-France, 17-18 June, 1997b.
13. Childs, T. H. C., "Elastic Effects in Metal Cutting Chip Formation", Int. J. Mech. Sci., 22, 457-466, 1980.
14. Childs, T. H. C., Otieno, A. M. W., and Maekawa, K., "The Influence of Material Flow Properties on the Machining of Steels", Proc. Third Int. Conf. on The Behaviour of Materials in Machining, (Institute of Materials), Warwick, 104-119, 15-17 Nov. 1994.
15. Childs, T. H. C., Bezas, K. and Dirikolu, M. H., The Sensitivity of Finite Element Predicted Machining Parameters to Small Variations in Flow Stress Behaviour, 2nd CIRP International Workshop on Machining, Nantes, France, Jan 24, 1999.
16. Clough, R. W., "The Finite Element in Plane Stress Analysis", Proc. 2nd ASCE Conf. on Electronic Computation, Pitsburg, PA, 1960.
17. Dirikolu, M. H., Computer Aided Simulation and Experimental Studies on Machining, Ph.D. Thesis, University of Leeds, Leeds, 1997.
18. Ernst, H. and Merchant, M. E., "Chip Formation, Friction and High Quality Machined Surfaces", Surface Treatment of Metals (ASM), 299-378, 1941.
19. Finnie, E., A "Comparison of Stress-Strain Behaviour in Cutting with That in Other Materials", Int. Res. Prod. Eng., ASME, N.Y., p.76, 1963.
20. Gordon, M. B., "The Applicability of the Binomial Law to the Process of Friction in the Cutting of Metals", Wear, 10, 274-290, 1967.
21. Huang, J. M. and Black, J. T., "An Evaluation of Chip Separation Criteria for the FEM Simulation of Machining", J. Manuf. Sci. Engg., 118, p.545, November 1996.
22. Iwata, K., Osakada, K., and Terasaka, Y., "Process Modelling of Orthogonal Cutting by Rigid-Plastic Finite Element Method", J. Eng. Ind., ASME., 106 ,p.32, 1984.
23. Kato, S., Yamaguchi, K., and Yamada, M., "Stress Distribution at the Interface Between Tool and Chip in Machining", J. Eng. Ind., Trans. ASME, p.683, May-1972.
24. Klamecki, B. E., Incipient Chip Formation in Metal Cutting - A 3-D Finite Element Analysis, Ph.D. Dissertation, Univ. of Illinois at Urbana Champaign, 1973.
25. Kobayashi, S. and Thomsen, E. G., "Metal Cutting Analysis-I: Re-evaluation and New Method of Presentation of Theories", J. Eng. Ind., 63-80, 1962.
26. Kudo, H., "Some New Slip-Line Solutions for Two-Dimensional Steady-State Machining", Int. J. Mech. Sci., 7, 43-55, 1965.
27. Lee, E. H. and Shaffer, B.W., "The Theory of Plasticity Applied to a Problem of Machining", J. Appl. Mech., 73 , p.405, 1951.
28. Lin, Z. C. and Lin, S. Y., "A coupled Finite Element Model of Thermo-Elastic-Plastic Large Deformation for Orthogonal Cutting", J. Eng. Matrl. Tech., Trans. ASME, 114, p.218, April 1992.
29. Merchant, M. E., "Mechanics of the Cutting Process", J. A Phys., 16, 267-275, 1945.
30. Oxley, P. L. B., Mechanics of Machining: An Analytical Approach to Assessing Machinability, Ellis Harwood, 1st Ed., 1989.
31. Rowe, G. W. et al., "Finite Element Plasticity and Metalforming Analysis", Cambridge University Press, 1991.
32. Shih, A. J. and Yang, H. T. Y., "Experimental and Finite Element Predictions of residual stresses due to Orthogonal Metal Cutting", Int. J. Num. Methods Eng., 36, 1487-1507, 1993.
33. Shirakashi, T. and Usui, E., "Simulation Analysis of Orthogonal Metal Cutting Mechanism", Proc. Int. Conf. on Prod. Eng., Tokyo , 535-540, 1974.
34. Strenkowski, J. S. and Carroll, J. T., "A Finite Element Model of Orthogonal Metal Cutting", J. Eng. Ind., ASME, 107, 2, 349-354, 1985.
35. Tay, A. A. O., "A Review of Methods of Calculating Machining Temperature", J. Matrl. Proc. Tech., 36, 225-257, 1993.
36. Tay, A. A. O., Stevenson, M.G., and de Vahl Davis, G., "Using Finite Element Method to Determine Temperature Distributions in Orthogonal Machining", Proc. I.Mech.E., 188, 627-638, 1974.
37. Usui, E. and Shirakashi, T., "Mechanics of Machining - From "Descriptive" to "Predictive" Theory", ASME Publ. PED Vol-7, 13-35, 1982.
38. Usui, E., Maekawa, K., and Shirakashi, T., "Simulation Analysis of Built-up Edge Formation in Machining of Low Carbon Steels", Bull. Jpn. Soc. Prec. Eng., 15, 237-242, 1981.
39. van Luttervelt, C. A., Childs, T. H. C., Jawahir, I.S., Klocke, F. and Venuvinod, P.K., Present Situation and Future Trends in Modelling of Machining Operations, CIRP Annals, vol 47, Part 2, 587-626, 1998.
40. Wu, J., Dillon, O.W.Jr., and Lu, W., "Thermo-Viscoplastic Modelling of Machining Process using a Mixed Finite Element Method", J. Eng. Matrl. Tech., Trans. ASME, 118, p.470, Nov. 1992.
41. Zhang, B. and Bagchi, A., "Finite Element Simulation of Chip Formation and Comparison with Machining Experiment", J. Eng. Ind., 116, p.289, Aug. 1994.
42. Zorev, N.N., "Interrelationship Between Shear Processes Occurring Along Tool Face and on Shear Plane in Metal Cutting", Proc. Conf. Int. Res. in Prod. Eng., 42-49, ASME, New York, 1963.