Elastic modulus by resonance of rectangular prisms: corrections for edge treatments

Journal of the American Ceramic Society

Volumn 83, Issue 2, 2000, Pages 317-320

  Quinn, George D ^a   Swab, Jeffrey J ^b  

^a NATIONAL INSTITUTE OF STANDARDS AND TECHNOLOGY   (United States)

^b U S ARMY RESEARCH LABORATORY   (United States)

Author keywords

[No Author keywords available]

Indexed keywords

DYNAMICS; ELASTIC MODULI; ELASTIC WAVES; NATURAL FREQUENCIES; NUMERICAL METHODS; POISSON RATIO; RESONANCE; VIBRATIONS (MECHANICAL); WAVE EQUATIONS;

CERAMIC SPECIMENS; CORRECTION FACTOR; EDGE CHAMFERS;

CERAMIC MATERIALS;

EID: 0033732973     PISSN: 00027820     EISSN: None     Source Type: Journal    
DOI: 10.1111/j.1151-2916.2000.tb01192.x     Document Type: Article

References (21)

1. S. Spinner and W. E. Tefft, *A Method for Determining Mechanical Resonance Frequencies and for Calculating Elastic Moduli from These Frequencies," Proc. Am. Soc. Test. Mater., 61, 1221-38 (1961).
2. S. Spinner, T. W. Reichard, and W. E. Tefft, "A Comparison of Experimental and Theoretical Relations Between Young's Modulus and the Flexural and Longitudinal Resonance Frequencies of Uniform Bars," J. Res. Natl. Bur. Stand., Sect. A. 64A [2] 147-55 (1960).
3. G. Pickett, "Equations for Computing Elastic Constants from Flexural and Torsional Resonant Frequencies of Vibration of Prisms and Cylinders," Proc. Am. Soc. Test. Mater., 45, 846-65 (1945).
4. R. W. Dickson and J. B. Wachtman, "An Alumina Standard Reference Material for Resonance Frequency and Dynamic Elastic Moduli Measurement, I For Use at 25°C,° J. Res. Natl. Bur. Stand., Sect. A, 75A [3] 155-62 (1971).
5. J. S. Smith, M. Wyrick, and J. M. Poole. °An Evaluation of Three Techniques for Determining the Young's Modulus of Mechanically Alloyed Materials"; pp. 195-207 in ASTM Special Technical Publication 1045, Dynamic Elastic Modulus Measurements in Materials. Edited by A. Wolfenden. American Society for Testing and Materials, West Conshohocken, PA, 1990.
6. F. Forster, New Method for Determination of Modulus of Elasticity and Damping," Z. Metallkd., 29, 109-15 (1937).
7. E. Goens, "Über die Bestimmung des Elastizitätsmoduls von Stäben mit Hilfe von Beigungsschwingungen," Ann. Phys. (Leipsig), 11, 649-78 (1931).
8. S. P. Timoshenko, "On the Transverse Vibrations of Bars of Uniform Cross Section." Philos. Mag. Ser. 6, 43, 125-31 (1922).
9. "Standard Test Method for Dynamic Young's Modulus. Shear Modulus, and Poisson's Ratio for Advanced Ceramics by Sonic Resonance," ASTM Designation C 1198-96, 1999 Annual Book of Standards, Vol. 15.01. American Society for Testing and Materials, West Conshohocken, PA.
10. "Standard Test Method for Dynamic Young's Modulus, Shear Modulus, and Poisson's Ratio by Sonic Resonance." ASTM Designation C 1875-98, 1999 Annual Book of Standards, Vol. 3.01. American Society for Testing and Materials, West Conshohocken, PA.
11. "Standard Test Method for Dynamic Young's Modulus, Shear Modulus, and Poisson's Ratio in Advanced Ceramics by Impulse Excitation of Vibration": see Ref. 9, ASTM Designation C 1259-96.
12. "Standard Test Method for Dynamic Young's Modulus, Shear Modulus, and Poisson's Ratio by Impulse Excitation of Vibration": see Ref. 10, ASTM Designation C 1876-98.
13. "Standard Test Method for Young's Modulus, Shear Modulus, and Poisson's Ratio for Glass and Glass-Ceramics by Resonance," ASTM Designation C 623-95, 1999 Annual Book of Standards, Vol. 15.02. American Society for Testing and Materials, West Conshohocken, PA.
14. "Standard Test Method for Young's Modulus, Shear Modulus, and Poisson's Ratio for Glass and Glass-Ceramics by Resonance"; ibid. ASTM Designation C 848-88.
15. F. Baratta, "Requirements for Flexure Testing of Brittle Materials," U.S. Army Rept. No. TR 82-20, U.S. Army Materials and Mechanics Research Center, Watertown, MA, April 1982.
16. F. Baratta, G. Quinn, and W. Matthews, "Errors Associated with Flexure Testing of Brittle Materials," U.S. Army Rept. No. MTL TR 87-35, U.S. Army Materials Technology Laboratory, Watertown, MA, July 1987.
17. W. H. Duckworth, "Precise Tensile Properties of Ceramic Bodies," J. Am. Ceram. Soc., 34 [1] 1-9 (1951).
18. "Standard Test Method for Flexural Strength of Advanced Ceramics at Ambient Temperatures"; see Ref. 9, ASTM Designation C 1161-94.
19. "Standard Test Method for Flexural Strength of Monolithic Ceramics at Room Temperature," 206 Draft International Standard Designation ISO/DIS 14704, Technical Committee TC. International Standards Organization, Geneva, Switzerland, 1999.
20. H. Schenck Jr., Theories of Engineering Experimentation; 2nd Ed. McGraw-Hill, New York, 1968.
21. J. Pople, "Errors and Uncertainties in Strain Measurements"; pp. 217-74 in Strain Gage Technology. 2nd Ed. Edited by A. L. Windrow. Elsevier Applied Sciences, London, U.K., 1989.