Sensor signals for tool-wear monitoring in metal cutting operations - a review of methods

International Journal of Machine Tools and Manufacture

Volumn 40, Issue 8, 2000, Pages 1073-1098

  Dimla Snr , Dimla E ^a  

^a DE MONTFORT UNIVERSITY   (United Kingdom)

Author keywords

[No Author keywords available]

Indexed keywords

ACOUSTIC EMISSIONS; MONITORING; SENSORS; SIGNAL PROCESSING; VIBRATIONS (MECHANICAL); WEAR OF MATERIALS;

TOOL CONDITION MONITORING SYSTEMS (TCMS);

METAL CUTTING;

EID: 0033728441     PISSN: 08906955     EISSN: None     Source Type: Journal    
DOI: 10.1016/S0890-6955(99)00122-4     Document Type: Article

References (83)

1. Shaw M.C. Metal Cutting Principles. 1984;Clarendon Press, Oxford. Chapter 3.
2. Schey J.A. Introduction to Manufacturing Processes. second ed. 1987;McGraw-Hill Book Company, London. Chapter 8.
3. Byrne G., Dornfeld D., Inasaki I., Ketteler G., König W., Teti R. Tool condition monitoring (TCM) - the status of research and industrial application. Annals of CIRP. 44(2):1995;541-567.
4. P.M. Lister. On-line measurement of tool wear. Ph.D. thesis, Manufacturing and Machine Tools Division, Department of Mechanical Engineering, UMIST, Manchester, UK, 1993.
5. Dan L., Mathew J. Tool wear and failure monitoring techniques for turning - a review. International Journal of Machine Tools and Manufacture. 30(4):1990;579-598.
6. Ravindra H.V., Srinivasa Y.G., Krishnamurthy R. Modelling of tool wear based on cutting forces in turning. Wear. 169:1993;25-32.
7. Warnecke G., Jenewein A., Reinfelder A. Tool monitoring based on process identification, monitoring and control for manufacturing processes. Winter Annual Meeting of the ASME, Dallas, TX, USA. 1990;43-55.
8. Novak A., Wiklund H. Reliability of tool-wear monitoring. Annals of the CIRP. 42(1):1992;63-66.
9. Choi G.S., Wang Z.X., Dornfeld D.A., Tsujino K. Development of an intelligent on-line tool wear monitoring system for turning operations. Proc. USA-Japan Symposium on Flexible Automation, A Pacific Rim Conference ISCIE Kyoto. 1990;683-690.
10. L.I. Burke, Automated identification of tool wear states in machining processes: an application of self-organising neural networks. Ph.D. thesis, Department of Industrial Engineering and Operations Research, UC at Berkeley, USA, 1989.
11. S. Rangwala, Machining process characterisation and intelligent tool condition monitoring using acoustic emission signal analysis. PhD thesis, Mechanical Engineering Department, UC at Berkeley, USA, 1988.
12. Prickett P.W., Johns C. An overview of approaches to end milling tool monitoring. International Journal of Machine Tools and Manufacture. 39(1):1999;105-122.
13. Kurada S., Bradley C. A review of machine vision sensors for tool condition monitoring. Computers in Industry. 34(1):1997;55-72.
14. Martin K.F. A review by discussion of condition monitoring and fault diagnosis in machine tools. International Journal of Machine Tools and Manufacture. 34(4):1994;527-551.
15. Shiraishi M. Scope of in-process measurement, monitoring and control techniques in machining processes - Part 1: In-process techniques for tools. Precision Engineering. 10(4):1988;179-189.
16. Martin K.F., Brandon J.A., Grosvenor R.I., Owen A. A comparison of in-process tool wear measurement methods in turning. Proceedings International 26th MATADOR Conference, Manchester, UK. 1986;289-296.
17. Teti R. A review of tool condition monitoring literature database. Annals of the CIRP. 44(2):1995;659-666.
18. Choi D., Kwon W.T., Chu C.N. Real-time monitoring of tool fracture in turning using sensor fusion. International Journal of Advanced Manufacturing Technology. 15(5):1999;305-310.
19. Jemielniak K., Otman O. Tool failure detection based on analysis of accoustic emission signals. Journal of Material Processing Technology. 76:1998;192-197.
20. Kakade S., Vijayaraghavan L., Krishnamurthy R. In-process tool wear and chip-form monitoring in face milling operation using acoustic emission. Journal of Material Processing Technology. 44:1994;207-214.
21. Zheng S.X., McBride R., Barton J.S., Jones J.D.C., Hale K.F., Jones B.E. Intrinsic optical fibre sensor for monitoring acoustic emission. Sensors and Actuators, A: Physical. 31:1992;110-114.
22. König W., Kutzner K., Schehl U. Tool monitoring of small drills with acoustic emission. International Journal of Machine Tools and Manufacture. 32(4):1992;487-493.
23. Blum T., Inasaki I. A study on acoustic emission from the orthogonal cutting process. ASME Trans. Journal of Engineering for Industry. 112(3):1990;203-211.
24. Moriwaki T., Tobito M. A new approach to automatic detection of life of coated tool based on acoustic emission measurement. ASME Trans. Journal of Engineering for Industry. 112(3):1990;212-218.
25. Roget J., Souquet P., Gsib N. Application of acoustic emission to the automatic monitoring of tool condition during machining. ASNDT Materials Evaluation. 46:1988;225-229.
26. Tansel I.N., McLaughlin C. On-line monitoring of tool breakage with unsupervised neural network. Trans. NAMR I/SME. 1991;364-370.
27. Lee L.C., Lee K.S., Gan C.S. On the correlation between dynamic cutting force and tool wear. International Journal of Machine Tools and Manufacture. 29(3):1989;295-303.
28. Yan D., El-Wardany T.I., Elbestawi M.A. A multi-sensor strategy for tool failure detection in milling. International Journal of Machine Tools and Manufacture. 35(3):1995;383-398.
29. Dornfeld D.A. Application of acoustic emission techniques in manufacturing. NDT and E International. 25(6):1992;259-269.
30. Dornfeld D.A. In process recognition of cutting states. JSME International Journal, Series C: Dynamics Control. 37(4):1994;638-650.
31. Boothroyd G. Fundamentals of Metal Machining and Machine Tools. 1975;McGraw-Hill, New York.
32. Trent E.M. Metal Cutting. 1977;Butterworths, London.
33. Sarwar M., Li J., Penlington R., Ahmed W. Development of thermal imaging systems for metal cutting applications. Proceedings Advanced Manufacturing Processes Systems and Technologies Conference (AMPST '96), Bradford, UK. 1996;361-369.
34. Lin J. Inverse estimation of the tool-work interface temperature in end milling. International Journal of Machine Tools and Manufacture. 35(5):1995;751-760.
35. Radulescu R., Kapoor S.G. An analytical model for prediction of tool temperature fields during continuous and interrupted cutting. ASME Trans. Journal of Engineering for Industry. 116(2):1994;135-143.
36. Raman S., Shaikh A., Cohen P.H. A mathematical model for tool temperature sensing. ASME Computational Methods in Materials Processing, PED. 61:1992;181-193.
37. Stephenson D.A., Ali A. Tool temperatures in interrupted metal cutting. Winter Annual Meeting of the ASME, PED. 43:1990;261-281.
38. Chow J.G., Wright P.K. On-line estimation of tool/chip interface temperatures for a turning operation. ASME Trans. Journal of Engineering for Industry. 110:1988;56-64.
39. Kitagawa T., Maekawa K., Shirakashi T., Usui E. Analytical prediction of flank wear of carbide tools in turning plain carbon steels (Part 1). Bull. Japan Soc. Precision Engineering. 22(4):1988;263-269.
40. Shaw M.C. Temperature in cutting. ASME Proceedings Symposium on Thermal Aspects in Manufacturing. 30:1988;133-143.
41. Dimla D.E. Snr Tool wear monitoring using cutting force measurements. 15th NCMR: Advances in Manufacturing Technology XIII, University of Bath, 6-8 September. 1999;33-37.
42. Bayramoglu M., Düngel Ü. A systematic investigation on the use of force ratios in tool condition monitoring for turning operations. Trans. Institute of Measurement and Control. 20(2):1998;92-97.
43. Ko T.J., Cho D.W. Cutting state monitoring in milling by a neural network. International Journal of Machine Tools and Manufacture. 34(5):1994;659-676.
44. Purushothaman S., Srinivasa Y.G. A back-propagation algorithm applied to tool wear monitoring. International Journal of Machine Tools and Manufacture. 34(5):1994;625-631.
45. Tarng Y.S., Hseih Y.W., Hwang S.T. Sensing tool breakage in face milling with a neural network. International Journal of Machine Tools and Manufacture. 34(3):1994;341-350.
46. Dornfeld D.A. Neural network sensor fusion for tool condition monitoring. Annals of the CIRP. 39(1):1990;101-105.
47. Lee K.S., Lee L.C., Teo S.C. On-line tool wear monitoring using a PC. Journal of Material Processing Technology. 29:1992;3-13.
48. Marques M.J.M., Mesquita R.M.D. Monitoring the wear of sintered high-speed steel tools. Journal of Material Processing Technology. 25:1991;195-213.
49. Kim J.S., Lee B.H. An analytical model of dynamic cutting forces in chatter vibration. International Journal of Machine Tools and Manufacture. 31(3):1991;371-381.
50. Oraby S.E., Hayhurst D.R. Development of models for tool wear force relationships in metal cutting. International Journal of Machine Tools and Manufacture, 33(2):1991;125-138.
51. Yao Y., Fang X.D., Arndt G. Comprehensive tool wear estimation in finish-machining via multivariate time-series analysis of 3-D cutting forces. Annals of the CIRP. 39(1):1990;57-60.
52. Yao Y., Fang X.D. Modelling of multivariate time series for tool wear estimation in finish-turning. International Journal of Machine Tools and Manufacture. 32(4):1992;495-508.
53. Shi T., Ramalingam S. Real-time flank wear sensing. Winter Annual Meeting of the ASME, PED. 43:1990;157-170.
54. Lee L.C., Lam K.Y., Liu X.D. Characterisation of tool wear and failure. Journal of Materials Processing Technology. 40:1994;143-153.
55. Elanayar S.V.T., Shin Y.C., Kumara S. Machining condition monitoring for automation using neural networks. Monitoring and Control of Manufacturing Processes, PED, 44:1990;85-100. Winter Annual Meeting of the ASME.
56. Gould L. Sensing tool and drive element conditions in machine tools. Sensor. 1988;5-13.
57. Dimla D.E. Snr, Lister P.M. On-line metal cutting tool condition monitoring - I: Force and vibration analyses. International Journal of Machine Tools and Manufacture. 40(5):2000;739-768.
58. Grabec I. Chaotic dynamics of the cutting process. International Journal of Machine Tools and Manufacture. 28(1):1988;19-32.
59. Khraisheh M.K., Pezeshki C., Bayoumi A.E. Time series based analysis for primary chatter in metal cutting. Journal of Sound and Vibration. 180(1):1995;67-87.
60. D.E. Dimla Snr., Multivariate tool condition monitoring in a metal cutting operation using neural networks. Ph.D. thesis, School of Engineering and the Built Environment, The University of Wolverhampton, UK, 1998.
61. El-Wardany T.I., Gao D., Elbestawi M.A. Tool condition monitoring in drilling using vibration signature analysis. International Journal of Machine Tools and Manufacture. 36(6):1996;687-711.
62. Yao Y., Fang X.D., Arndt G. On-line estimation of groove wear in the minor cutting edge for finish machining. Annals of the CIRP. 40(1):1991;41-44.
63. Rotberg J., Braun S., Lenz E. Mechanical signature analysis in interrupted cutting. Annals of the CIRP. 36(1):1987;249-252.
64. Rotberg J., Braun S., Lenz E. Vibration generation models for cutting tool monitoring. Diagnostics, Vehicle Dynamics and Special Topics - ASME Design Engineering Division. 18(5):1989;1-6.
65. Jiang C.Y., Zhang Y.Z., Xu H.J. In-process monitoring of tool wear stage by the frequency band-energy method. Annals of the CIRP. 36(1):1987;45-48.
66. Lister P.M., Barrow G. Tool condition monitoring systems. Proceedings International 26th MATADOR Conference, Manchester, UK. 1986;271-288.
67. Oguamanam D.C.D., Raafat H., Taboun S.M. A machine vision system for wear monitoring and breakage detection of single-point cutting tools. Computers in Industrial Engineering. 26(3):1994;575-598.
68. Du R., Zhang B., Hungerford W., Pryor T. Tool condition monitoring and compensation in finish turning using optical sensor. ASME Symposium Mechatronics, PED. 63:1993;245-251.
69. Cuppini D., D'Enrrico G., Rutelli G. Tool image processing with application to unmanned metal-cutting, a computer vision system for wear sensing and failure detection. SPIE. 701:1986;416-422.
70. Wong Y.S., Nee A.Y.C., Li X.Q., Reisdorf C. Tool condition monitoring using laser scatter pattern. Journal of Materials Processing Technology. 63:1997;205-210.
71. Noori-Khajavi A., Komanduri R. Frequency and time domain analyses of sensor signals in drilling - I. Correlation with drill wear. International Journal of Machine Tools and Manufacture. 35(6):1995;775-793.
72. Zhou J.M., Andersson M., Ståhl J.E. A system for monitoring cutting tool spontaneous failure based on stress estimation. Journal of Materials Processing Technology. 48:1995;231.
73. El Gomayel J.I., Bregger K.D. On-line tool wear sensing for turning operations. ASME Trans. Journal of Engineering for Industry. 108:1986;44-47.
74. Zhang D., Dai S., Han Y., Chen D. On-line monitoring of tool breakage using spindle current in milling. 1st Asia-Pacific and 2nd Japan-China International Conference Progress of Cutting and Grinding, Shanghai, China, September. 1994;270-276.
75. Constantinides N., Bennett S. An investigation of methods for on-line estimation of tool wear. International Journal of Machine Tools and Manufacture. 27(2):1987;225-237.
76. Rangwala S., Dornfeld D. Integration of sensors via neural networks for detection of tool wear states. Winter Annual Meetings of the ASME, PED. 25:1987;109-120.
77. Rangwala S., Dornfeld D. Sensor integration using neural networks for intelligent tool condition monitoring. ASME Trans. Journal of Engineering for Industry. 112(3):1990;219-228.
78. Jetley S.K., Gollajesse A. Measuring tool wear using magnetism. Proceedings: Japan-USA Symposium Flexible Automation - A Pacific Rim Conference, July 11-18, Kobe, Japan. 1994;345-347.
79. Abu-Zahra N.H., Nayfeh T.H. Calibrated method for ultrasonic on-line monitoring of gradual wear during turning operations. International Journal of Machine Tools and Manufacture. 37(10):1997;1475-1484.
80. Weck M. Metrological Analysis and Performance Tests. Handbook of Machine Tools. fourth ed. 1984;Vol. 4, John Wiley and Sons, Chichester.
81. Holmbom P., Pedersen O., Sandell B., Lauber A. Fusing sensor systems: promises and problems. Sensor Reviews. 9(3):1989;143-152.
82. Parra L., Deco G., Miesbach S. Statistical independence and novelty detection with information preserving non-linear maps. Neural Computation. 8:1996;260-269.
83. Tanner R., Loh N.K. A taxonomy of multi-sensor fusion. Journal of Manufacturing Systems. 11(5):1994;314-325.