Residual stress and sub-surface flow in finish hard turned AISI 4340 and 52100 steels: A comparative study

American Society of Mechanical Engineers, Manufacturing Engineering Division, MED

Volumn 10, Issue , 1999, Pages 831-837

  Ramesh, Anand ^b   Thiele, Jeffrey D ^a,b   Melkote, Shreyes N ^b  

^a CATERPILLAR INC   (United States)

^b GEORGIA INSTITUTE OF TECHNOLOGY   (United States)

Author keywords

[No Author keywords available]

Indexed keywords

COMPRESSIVE STRESS; PLASTIC FLOW; RESIDUAL STRESSES; STEEL;

HARD TURNING; STEEL AISI 4340; STEEL AISI 52100;

TURNING;

EID: 0033354569     PISSN: None     EISSN: None     Source Type: Conference Proceeding    
DOI: None     Document Type: Article

References (17)

1. Abrao A. M., Aspinwall, D. K., 1996, "The Surface Integrity of Turned and Ground Bearing Steel", Wear, Vol. 196, pp. 215-220
2. ASM Metals Handbook, 1990, Vol. 4, American Society of Metals, Metals Park, OH.
3. Bailey, J. A., Jeelani, S., and Becker, S. E., 1976, "Surface Integrity in Machining AISI 4340", Trans. ASME, J. Eng. Ind., pp. 999-1007
4. Brinksmeier, E., Cammett, J. T., , Konig, W., Leskovar, P., Peters, J., Tonshoff H. K., 1982, "Residual Stresses - Measurement and Causes in Machining Processes", Annals of the CIRP, Vol. 31, pp. 491-510
5. Chou, Y. K., Evans, C. J., 1998, "Process Effects in White Layer Formation in Hard Turning", Trans. NAMRI/SME, Vol. XXVI, pp. 117-122
6. Field, M., and Kahles, J. F., 1971, "Review of Surface Integrity of Machined Components," Annals of CIRP, Vol. 20, No. 2, p. 153.
7. Inoue, T., Tanaka, K., 1975, "An elastic plastic stress analysis of quenching when considering a transformation", Int. J. Mech. Sci., Vol. 17, pp. 361-367
8. Konig, W., Berktold, A., Kock, K-F., 1993, "Turning vs. Grinding - A Comparison of Surface Integrity Aspects and Attainable Accuracies", Annals of the CIRP, Vol. 42, pp. 39-43
9. Matsumoto, Y., Barash, M. M., Liu, C. R., 1986, "Effect of Hardness on the Surface Integrity of AISI 4340 Steel", Trans. ASME, J. Eng. Ind., Vol. 108, pp. 169-175
10. Noyan, I. C., Cohen, J. B, 1987, Residual Stress : Measurement by Diffraction and Interpretation, Springer-Verlag, New York
11. Sadat, A. B., 1987, Bailey, J. A., "Residual Stresses in Turned AISI 4340 Steel", Experimental Mechanics, pp. 80-85
12. Sadat, A. B., 1990, "Effect of High Cutting Speed on Surface Integrity of AISI 4340 Steel during Turning", Matls. Sci. & Tech., Vol. 6, pp. 371-375
13. Schimmel, R. J., Manjunathiah, J., Endres, W. J., 1997, "An Experimental Investigation into the Variability of Edge Hones and their Effects on Machining Forces", Manufacturing Science and Engineering, ASME Bound Volume, MED-Vol. 6-2, pp. 261-267
14. Thiele, J. D., Melkote, S. N., 1999a, "Effect of Cutting Edge Geometry and Workpiece Hardness on Workpiece Sub-Surface Deformation and Through Thickness Residual Stresses for Hard Turning of AISI 52100 Steel", Trans. NAMRI/SME, Vol XXVII pp. 135-140.
15. Thiele, J. D., Melkote, S. N., Watkins T. R., Peascoe R. A., 1999b, "Effect of Cutting Edge Geometry and Workpiece Hardness on Surface Residual Stresses in Finish Hard Turning of AISI 52100 Steel", in ASME Proceedings, Symp. on Machining and Grinding of Hard Materials.
16. Thiele, J. D., Melkote, S. N., 1999c, "Effect of Cutting Edge Geometry and Workpiece Hardness on Surface Generation in Finish Hard Turning of AISI 52100 Steel", J. Matls. Proc. Tech., in press.
17. Tonshoff, H. K., Wobker, H-G., Brandt, D., 1995, "Hard Turning - Influences on the Workpiece Properties", Trans. NAMRI/SME, Vol. XXIII, pp. 215-220