Residual stress analysis in orthogonal machining of standard and resulfurized AISI 316L steels

Journal of Materials Processing Technology

Volumn 96, Issue 1-3, 1999, Pages 225-233

  M'Saoubi, R ^a   Outeiro, J C ^b   Changeux, B ^a   Lebrun, J L ^a   Morao Dias A ^b  

^a CNRS   (France)

^b UNIVERSITY OF COIMBRA   (Portugal)

Author keywords

[No Author keywords available]

Indexed keywords

AUSTENITE; CORROSION RESISTANCE; CUTTING TOOLS; MACHINING; METAL CUTTING; RESIDUAL STRESSES; STRESS ANALYSIS; TEMPERATURE DISTRIBUTION; X RAY DIFFRACTION ANALYSIS;

CUTTING FORCES; CUTTING PARAMETERS; CUTTING TEST; ORTHOGONAL MACHINING; RESULFURIZED STEEL; TOOL TEMPERATURE;

STAINLESS STEEL;

EID: 0033225559     PISSN: 09240136     EISSN: None     Source Type: Journal    
DOI: 10.1016/S0924-0136(99)00359-3     Document Type: Article

References (23)

1. E.M. Trent, Metal Cutting, Butterworth/Heinemann, London, 1991.
2. E.K. Henriksen, Residual stresses in machined surfaces, Trans. ASME 73 (January 1951), 265-278.
3. Okushima K., Kakino Y. A study on the residual stress produced by metal cutting. Memoirs of the Faculty of Engineering, Kuyoto. 34:1972;234-248.
4. Liu C.R., Barash M.M. The mechanical state of the sub-layer of a surface generated by chip removal process, Part I: Cutting with a sharp tool. Trans. ASME. 98(4):1976;257-264.
5. Matsumoto Y., Barash M.M., Liu C.R. Effect of hardness on surface integrity of AISI 4340 steel. ASME J. Eng. Indust. 108:1986;169-175.
6. Wu D.W., Matsumoto Y. The effect of hardness on residual stresses in orthogonal machining of AISI 4340 Steel. ASME J. Eng. Indust. 112:1990;245-252.
7. Brinksmeier E. Residual stresses in hard metal cutting. Residual Stresses Sci. Technol. 2:1987;839-847.
8. B. Scholtes, Residual stresses introduced by machining, in: Advance in Surface Treatments, Technology-Applications-Effects, International Guidebook on Residual Stresses, vol. 4, Pergamon Press, Oxford, 1987, pp. 59-71.
9. Schreiber E., Schlicht H. Residual stresses after turning of hardened components. Residual Stresses Sci. Technol. 2:1987;853-860.
10. Jeelani S., Bailey J.A. Residual stress distribution in machining annealed 18% nickel maraging steel. ASME J. Eng. Mater. Technol. 108:1986;93-98.
11. 2 solution, ICM3, vol. 2, Cambridge, 1979, pp. 603-610.
12. G.M. Smith, J.F. Riley, Residual Stresses in Austenitic Generator End-Rings, ICRS2, Elsevier Applied Science, Amsterdam, 1989, pp. 728-733.
13. Wiesner C. Residual stresses after orthogonal machining of AISI 304: numerical calculation of the thermal component and comparison with experimental results. Metall. Trans. A. 23:1989;989-996.
14. Yang D.Y., Watkins T.R., Kozaczek K.J., Hubbard C.R., Cavin O.B. Surface residual stresses in machined austenitic stainless steels. Wear. 194:1996;168-173.
15. C. Le Calvez, Etude des aspects thermiques et métallurgiques de la coupe orthogonale d'un acier au carbone, Thesis, Ecole Nationale Supérieure Des Arts Et Métiers, Paris, 1995.
16. M'Saoubi R., Le Calvez C., Lebrun J.-L. Influence of tool nature and coating on the temperature distribution during chip formation in orthogonal cutting of steels. Matériaux et Techniques. 9/10:1997;37-42.
17. G. Maeder, J.L. Lebrun, J.M. Sprauel, Détermination par diffraction des rayons X des contraintes internes. Aspects macro et microscopiques, Ecole d'Eté d'Oléron: Physique et Mécanique de la Mise en Forme des Matériaux, Presses du CNRS-IRSID, 1990.
18. J.-L. Lebrun, R. M'Saoubi, B. Changeux, A new method for cutting tool temperature measurement using CCD infrared technique: The influence of tool nature and coating, CIRP International Workshop on Modeling of Machining Operations, Atlanta, Georgia, USA, 19 May 1998.
19. J. Outeiro, Comportamento do aço AISI 316L em Torneamento Ortogonal, Thesis, Department of Mechanics Engineering of University of Coimbra, Coimbra, 1998.
20. O. Bletton, R. Duet, R. Heritier, Usinabilité des aciers inoxydables, in: P. Lacombe, B. Baroux, G. Beranger (Eds.), Les aciers inoxydables, Les Editions de Physique, 1990, pp. 776-779.
21. D.A. Stephenson, J.S. Agapiou, Metal Cutting - Theory and Practice, Marcel Dekker, New York, 1997.
22. R. M'Saoubi, Aspects thermiques et microstructuraux de la coupe, Thesis, Ecole Nationale Supérieure des Arts et Métiers, Paris, 1998.
23. L. Jiang, Å. Roos, P. Liu, The influence of austenite grain size and its distribution on chip deformation and tool life during machining of AISI 304L, Metall. Mater. Trans. A 28A, 1997 2415-2422.