Dynamically loaded finite length journal bearings: Analytical method of solution

Journal of Tribology

Volumn 121, Issue 4, 1999, Pages 844-852

  Hirani, H ^a   Athre, K ^a   Biswas, S ^a  

^a INDIAN INSTITUTE OF TECHNOLOGY DELHI   (India)

Author keywords

[No Author keywords available]

Indexed keywords

CRANKSHAFTS; CURVE FITTING; DYNAMIC LOADS; FINITE ELEMENT METHOD; PRESSURE DISTRIBUTION;

CLOSED FORM PRESSURE DISTRIBUTION;

JOURNAL BEARINGS;

DYNAMICS; JOURNAL BEARING; MATHEMATICAL MODELING; OIL FILM; PRESSURE;

EID: 0033213644     PISSN: 07424787     EISSN: 15288897     Source Type: Journal    
DOI: 10.1115/1.2834144     Document Type: Article

References (16)

1. Booker, J. F., 1965, Dynamically Loaded Journal Bearings: Mobility Method of Solution,” ASME Journal of Basic Engineering, pp. 537-546.
2. Booker, J. F., 1969, “Dynamically Loaded Journal Bearings: Maximum Film Pressure,” ASME Journal of Lubrication Technology, Vol. 91, pp. 534-543.
3. Booker, J F., 1971, “Dynamically Loaded Journal Bearings: Numerical Application of the Mobility Method,” ASME Journal of Lubrication Technology, Vol. 93, pp, 168-176.
4. Conway-Jones, J. M., Martin, F. A., and Gojon, R., 1991, “Refinement of Engine Bearing Design Techniques,” Tribology International, Vol. 24, pp. 119-127.
5. Gupta, B. K., 1963 “Analysis of Dynamically Loaded Long and Short Bearings,” Ph.D. thesis, Cornell University, pp. 12-14.
6. Goenka, P. K., 1984a, “Analytical Curve Fits for Solution Parameters of Dynamically Loaded Journal Bearings,” ASME Journal of Tribology, Vol. 106, pp. 421-428.
7. Goenka, P. K., 1984b, “Dynamically Loaded Journal Bearings: Finite Element Method Analysis,” ASME Journal of Tribology, Vol. 106, pp. 429-439.
8. Labouff, G. A., and Booker, J. F., 1985, “Dynamically Loaded Journal Bearings: A Finite Element for Rigid and Elastic Surfaces,” ASME Journal of Tribology, Vol. 107, pp. 505-515.
9. Martin, F. A., 1995, “Dynamically Loaded Journal Bearings: Position of Maximum Pressure Ratio,” ASME Journal of Tribology, Vol. 117, pp. 558-560.
10. Moes, H., and Bosma, R., 1981, “Mobility and Impedance Definitions for Plain Journal Bearing,” ASME Journal of Lubrication Technology, Vol. 103, pp. 468-470.
11. Paranjpe, R., and Goenka, P. K., 1990, “Analysis of Crankshaft Bearings using a Mass Conserving Algorithm,” STLE Tribology Transactions, Vol. 33, pp. 333-344.
12. Paranjpe, R. S., and Han, T., 1995, “A transient Thermohydrodynamic analysis Including Mass Conserving Cavitation for Dynamically Loaded Journal Bearings,” ASME Journal of Tribology, Vol. 117, pp. 369-378.
13. Ritchie, G. S., 1975, “The Prediction of Journal Loci in Dynamically Loaded Internal Combustion Engine Bearings,” Wear, Vol. 35, pp. 291-297.
14. Reason, B. R., and Narang, l. P., 1982, “Rapid Design and Performance Evaluation of Steady State Journal Bearings-A Technique Amenable to Programmable Hand Calculators,” ASLE Transactions, Vol. 25, pp. 429-444.
15. h Leeds Lyon Symposium on Tribology, Leeds, Dowson et al., ed., pp. 81-89.
16. Vincent, B., Maspeyrot, P., and Frene, J., 1996, “Cavitation in Dynamically Loaded Journal Bearing using Mobility Method,” Wear, Vol. 193, pp. 151-162