Effects of a groove on the behavior of a squeeze film between a grooved and a plain rotating annular disk

Journal of Tribology

Volumn 121, Issue 4, 1999, Pages 808-815

  Razzzaque, M Mahbubur ^a   Kato, Takahisa ^a  

^a UNIVERSITY OF TOKYO   (Japan)

Author keywords

[No Author keywords available]

Indexed keywords

COMPUTER SIMULATION; ENERGY DISSIPATION; MATHEMATICAL MODELS; MECHANICAL VARIABLES MEASUREMENT; SPEED; SURFACE PROPERTIES; TORQUE;

GROOVING; SQUEEZE FILMS;

ROTATING DISKS;

CLUTCH; DISC; GROOVE; MATHEMATICAL MODELING; SQUEEZE FILM;

EID: 0033213281     PISSN: 07424787     EISSN: 15288897     Source Type: Journal    
DOI: 10.1115/1.2834139     Document Type: Article

References (28)

1. Archibald, F. R., 1956, “Load Capacity and Time Relations for Squeeze Films,” Trans. ASME, Vol. 78, pp. 29-35.
2. Berger, E. J., Sadeghi, F., and Krousgrill, C. M., 1996, “Finite Element Modeling of Engagement of Rough and Grooved Wet Clutches,” ASME Journal of Tribology, Vol. 118, pp. 137-146.
3. Constantinescu, V. N., and Galetuse, S., 1992, “On Extending the Narrow SpiralGroove Theory to Configurations of Interest in Seals,” ASME Journal of Tribology, Vol, 114, pp. 563-566.
4. Dowson, D., 1961, “Inertia Effects in Hydrostatic Thrust Bearings,” ASME Journal of Basic Engineering, pp. 227-234.
5. Hsing, F. C., 1972, “Formulation of a Generalized Narrow Groove Theory for Spiral Grooved Viscous Pumps,” ASME Journal of Lubrication Technology, Vol. 94, No. 1, pp. 81-85.
6. Jang, J., and Khonsari, M., 1999, “Thermal Characteristics of a Wet Clutch,” ASME Journal of Tribology, Vol. 121, July, p. 610.
7. Lloyd, F. A., 1974, “Parameters Contributing to Power Loss in Disengaged Wet Clutches,” SAE technical paper series, paper no. 740676.
8. Malanoski, S. B., and Pan, C. H. T., 1965, “The Static and Dynamic Characteristics of the Spiral-Grooved Thrust Bearing,” ASME Journal of Basic Engineering, Vol. 87, pp. 547-558.
9. Megat, A. M. M. H., Gethin, D. T., Claypole T. C., and Roylance, B. J., 1998, “Numerical and Experimental Investigation into Porous Squeeze Films,” Tribology International, Vol. 31, pp. 189-199.
10. Moore, D. F., 1965, “A Review of Squeeze Films,” Wear, Vol. 8, pp. 245-263.
11. Murti, P. R. K., 1974, “Squeeze-Film Behavior in Porous Circular Disks,” ASME Journal of Lubrication Technology, pp. 206-209.
12. Natsumeda, S., and Miyoshi, T., 1994, “Numerical Simulation of Engagement of Paper based Wet Clutch Facing,” ASME Journal of Tribology, Vol. 116, pp. 232-237.
13. Prakash, J., and Vij, S. K., 1973, “Load Capacity and Time-Height Relations For Squeeze Films Between Porous Plates,” Wear, Vol. 24, pp. 309-322.
14. Prakash, J., and Vij, S. K., 1976, “Effect of Velocity Slip on the Squeeze Film Between Rotating Porous Annular Discs,” Wear, Vol. 38, pp. 73-85.
15. Razzzaque, M. M., and Kato, T., 1998a “Viscous Torque Behavior of Grooved Wet Disks Sliding at Small Gaps,” Proc. JAST Tribology Conference, Tokyo, pp. 144-146.
16. Razzzaque, M. M., 1998b, “Viscous Torque Behavior of Grooved Wet Clutches,” Ph.D. dissertation, Department of Mechanical Engineering, The University of Tokyo, Japan.
17. Razzzaque, M. M., and Kato, T. 1998c, “Effect of Grooves on Wet-Clutch Engagement Behavior,” Proc. NORDTRIB’98: 8th International Conference on Tribology, 7-10 June, Ebeltoft, Denmark, pp. 649-656.
18. Razzzaque, M. M., and Kato, T., 1998d, “Squeeze Film Between a Grooved and a Porous Faced Rotating Annular Disk,” submitted to IMechE J. Engg. Trib.
19. Razzzaque, M. M., and Kato, T., 1999, “Effects of Groove Orientation on Hydrodynamic Behavior of Wet Clutch Coolant Films,” ASME Journal of Tribology, Vol. 121, pp. 56-61.
20. Sato, Y., Ono, K., and Iwama, A., 1990, “The Optimum Groove Geometry for Spiral Groove Viscous Pumps,” ASME Journal of Lubrication Technology, Vol. 112, pp. 409-414.
21. Ting, L. L., June 1972, “A Mathematical Analogue for Determination of Porous Annular Disk Squeeze Film Behavior Including the Fluid Inertia Effect,” ASME Journal of Basic Engineering, pp. 417-421.
22. Ting, L. L., 1975, “Engagement Behavior of Lubricated Porous Annular Disks. Part I: Squeeze Film Phase-Surface Roughness and Elastic Deformation Effects,” Wear, Vol. 34, pp. 159-172.
23. Vohr, J. H., and Chow, C. Y., 1965, “Characteristics of Herringbone-Grooved, Gas-Lubricated Journal Bearings,” ASME Journal of Basic Engineering, Vol. 87, pp. 568-578.
24. Wu, H., 1970, “Squeeze Film Behavior of Porous Annular Disks,” ASME Journal of Lubrication Technology, Vol. 92, pp. 593-596.
25. Wu, H., 1971, “The Squeeze Film Between Rotating Porous Annular Disks,” Wear, Vol. 18, pp. 461-470.
26. Wu, H., 1972, “Effect of Velocity Slip on the Squeeze Film Between Porous Rectangular Plates,” Wear, Vol. 20, pp. 67-71.
27. Wu, H., 1973, “An Analysis of the Engagement of Wet-Clutch Plates,” Wear, Vol. 24, pp. 23-33.
28. Wu, H., 1978, “A Review of Porous Squeeze Films," Wear, Vol. 47, pp. 371-385