A theoretical model of micro-pool lubrication in metal forming

Journal of Tribology

Volumn 121, Issue 4, 1999, Pages 731-738

  Lo, Sy Wei ^a,b   Wilson, William R D ^a  

^a Northwestern University   (United States)

^b NATIONAL YUNLIN UNIVERSITY OF SCIENCE AND TECHNOLOGY   (Taiwan)

Author keywords

[No Author keywords available]

Indexed keywords

FRICTION; INTERFACES (MATERIALS); MATHEMATICAL MODELS; METAL FORMING; VISCOPLASTICITY;

MICRO-POOL LUBRICATION; PERMEATING FILMS;

LUBRICATION;

HYDRODYNAMIC LUBRICATION; MATHEMATICAL MODELING; METAL WORKING;

EID: 0033201539     PISSN: 07424787     EISSN: 15288897     Source Type: Journal    
DOI: 10.1115/1.2834129     Document Type: Article

References (23)

1. Azushima, A., 1995, “Direct Observation of Contact Behavior to Interpret the Pressure Dependence of the Coefficient of Friction in Sheet metal Forming,“Annals of CIRP, Vol. 44, pp. 209-212.
2. Chang, D-F, Wilson, W. R. D., and Marsault, N., 1996, “Lubrication of Strip Rolling in the Low-Speed Mixed Regime,“STLE, Tribology Trans., Vol. 39, pp. 407-415.
3. Chung, K. J., Lo, S. W., and Horng, T. C., 1997, “Experimental Investigation of Low Speed Lubrication in Bulk Metal Forming Processes,” Proc. 14th National Conf on Mech. Eng., CSME, Chungli, Taiwan (in Chinese).
4. Felder, I., and Samper, V., 1994, “Experimental Study and Theoretical Interpretation of the Frictional Mechanisms in Steel Sheet Forming,” Wear, Vol. 178, pp. 85-94.
5. Howser, B., 1992, “A Micromechanical Model for Boundary Friction and Surface Topography Evolution in Strip Rolling,” Ph.D. dissertation, Mechanical Engineering, Northwestern University.
6. Ike, H., 1996, “Properties of Metal Sheets with 3-D Designed Surface Microgeometry Prepared by Special Rolls,” J. Mater. Proc. Tech., Vol. 60, pp. 363-378.
7. Kataoka, S., Kanno, K., and Kihara, J., 1988, “Experimental Investigation of Lubrication Mechanism in Low Speed Plastic Deformation I, II and III,” JSTP, Ann., Rep., Vol. 56.
8. Kudo, H., 1965, “A Note on the Role of Microscopically Trapped Lubricant at the Tool-Work Interface,” Int. J. Mech. Set, Vol. 7, pp. 383-388.
9. Kudo, H., and Azushima, A., 1987, “Interaction of Surface Microstructure and Lubricant in Metal Forming Tribology,” Proc. 2nd. Int. Conf on Adv. Technol of Plasticity, Stuttgart, p. 373.
10. Lin, H. S., Marsault, N., and Wilson, W. R. D., 1998, “A Mixed Lubrication Model for Cold Strip Rolling, Part I: Theoretical,” STLE Tribology Trans., Vol. 41, 3, pp. 317-326.
11. Lo, S. W., 1994, “A Study on the Flow Phenomena in the Mixed Lubrication Regime by Porous Medium Model,” ASME Journal of Tribology, Vol. 116, No. 3, pp. 640-647.
12. Lo, S. W., 1995, “Die-Workpiece Interfacial Behaviors in Axisymmetric Forging Processes with Flat Dies,” STLE Tribology Trans., Vol. 38, No. 3, pp. 663-671.
13. Lo, S. W., and Chung, K. J., 1998, “The Optimum Condition of Manufacturing a Smooth Engineered Surface by Internal-Ironing Process,” STLE Tribology Trans., Vol. 41, No. 4.
14. Mizuno, T., and Okamoto, M., 1982, “Effects of Lubricant Viscosity at Pressure and Sliding Velocity on Lubricating Conditions in the Compression-Friction Test on Sheet Metals,” ASME Journal of Lubrication Technology, Vol. 104, pp. 53-59.
15. Patir, N., and Cheng, H. S., 1978, “An Average Flow Model for Determining Effects of Three-Dimensional Roughness on Partial Hydrodynamic Lubrication,” ASME Journal of Lubrication Technology, Vol. 100, pp. 12-17.
16. Patir, N., and Cheng, H. S., 1979, “An Application of Average Flow Model to Lubrication Between Rough Sliding Surfaces,” ASME Journal of Lubrication Technology, Vol. 101, No. 2, pp. 220-230.
17. Ruan, F., Kudo, H., Tsubouch, M., and Hori, T., 1988, “Experimental Evidence of the Micro-Plasto Hydrodynamic Lubrication Mechanism,” JSTP, Ann. Rep., Vol. 24, pp. 41-48.
18. Wilson, W. R. D., 1971, “The Temporary Breakdown of Hydrodynamic Lubrication During the Initiation of Extrusion,” Int. J. Mech. Sci., Vol. 13, pp. 1728.
19. Wilson, W. R. D., and Sheu, S., 1988, “Real Area of Contact and Boundary Friction in Metal Forming,” Int. J. Mech. Sci., Vol. 30, No. 7, pp. 475-489.
20. Wilson, W. R. D., 1988, “Friction Models for Metal Forming in the Boundary Lubrication Regime,” ASME, pp. 13-23. (also in J. of Eng. Materials and Technology.)
21. Wilson, W. R. D., 1990, “Mixed Lubrication in Metalforming Processes,” Advanced Technology of Plasticity, Vol. 4, pp. 1667-1676.
22. Wilson, W. R. D., 1995, “Low-Speed Mixed Lubrication of Metal Forming Processes,” Annals of CIRP, Vol. 44(1), pp. 205-208.
23. Wilson, W. R. D., and Chang, D-F, 1996, “Low Speed Mixed Lubrication of Bulk Metal Forming Processes,” ASME Journal of Tribology, Vol. 118, pp. 83-89