Effects of post-drawing treatments on the fatigue strength of eutectoid steel wires

Fatigue and Fracture of Engineering Materials and Structures

Volumn 22, Issue 9, 1999, Pages 753-760

  Katagiri, K ^a   Sato, T ^a   Kasaba, K ^a   Sasaki, S ^b   Tashiro, H ^a  

^a IWATE UNIVERSITY   (Japan)

^b NIPPON STEEL CORPORATION   (Japan)

Author keywords

[No Author keywords available]

Indexed keywords

CRACK INITIATION; HARDNESS; RESIDUAL STRESSES; SHOT PEENING; STRAIN; WIRE;

BLUING; EUTECTOID STEEL WIRES; POST DRAWING TREATMENTS;

FATIGUE OF MATERIALS;

EID: 0033187890     PISSN: 8756758X     EISSN: None     Source Type: Journal    
DOI: 10.1046/j.1460-2695.1999.t01-1-00212.x     Document Type: Article

References (22)

1. H. Sunwoo, M. E. Fine, M. Meshii and D. H. Stone (1982) Cyclic deformation of pearlitic eutectoid rail steel. Met. Trans. A 13A, 2035-2046.
2. M. Dollar, I. M. Bernstein and A. W. Thompson (1988) Influence of deformation substructure on flow and fracture of fully pearlitic steel. Acta Metall. 36, 311-320.
3. Y. Kuroshima, S. Harada, K. Ogawa and M. Isaji (1995) Fatigue properties of very thin steel wire under fluctuating tension. J. Soc. Mat. Sci., Japan 44, 551-556 (in Japanese).
4. K. Katagiri, T. Sato, H. S. Shin, M. Takahashi, H. Mori, H. Tashiro and S. Sasaki (1997) Effects of drawing strain and bluing on the fatigue strength of eutectoid steel wires. Fatigue Fract. Engng Mater. Struct. 20, 1677-1686.
5. G. T. Gray III, A. W. Thompson and J. C. Williams (1985) Influence of microstructure on fatigue crack initiation in fully pearliric steels. Met. Trans. A 16A, 753-760.
6. M. A. Deaubler and A. W. Thompson (1986) Microstructural effects on short cracks in eutectoid steels. In: Small Fatigue Cracks. Proc International Workshop on Small Fatigue Cracks. (Edited by R. O. Richie and J. Lankford). The Metallurgical Society of AIME, Warrendale, Pa, pp. 157-164.
7. M. A. Deaubler, A. W. Thompson and I. M. Bernstein (1990) Influence of microstructure on fatigue behavior and surface fatigue crack growth of fully pearlitic steels. Met. Trans. A 21A, 925-933.
8. P. W. Kao and J. G. Byrne (1982) Fatigue initiation study of TMT eutectoid steel. Met. Trans. A 13A, 855-864.
9. J. L. Lorca and V. Sanchez-Galvez (1989) Fatigue limit and fatigue life prediction in high strength cold drawn eutectoid steel wires. Fatigue Fract. Engng Mater. Struct. 12, 31-45.
10. T. Sato, K. Katagiri, K. Konno, Y. Shoji, M. Ueda, M. Kikuchi and T. Yamasaki (1994) Factors relevant to fatigue strength of eutectoid steel wires. Trans. Jpn. Soc. Mech. Engng A. 60, 1333-1338 (in Japanese).
11. T. Ueda and K. Asakura (1957) Investigation on the fatigue properties of steel wire; (part 1) effect of the reduction by drawing and the low-temperature annealing upon the fatigue strength of high carbon steel wire. Mater. Testing 6, 386-391 (in Japanese).
12. K. J. Miller, H. J. Mohamed, M. W. Brown and E. R. De Los Rios (1986) Barriers to short fatigue crack propagation at low stress amplitude in a banded ferrite-pearlite structure. In: Small Fatigue Cracks. Proc. International Workshop on Small Fatigue Cracks. (Edited by R. O. Richie and J. Lankford). The Metallurgical Society of AIMIE, Warrendale, Pa, pp. 639-656.
13. G. Langford (1977) Deformation of pearlite. Met. Trans. A 8A, 861-875.
14. E. T. Gill and R. Goodacre (1935) Some aspect of the fatigue properties of patented steel wires. II - Note on the effect of lowtemperature heat treatment. J. Iron Steel hist. 130 (II), 143-165.
15. T. Ueda, K. Asakura and K. Kurane (1960) Investigation on the fatigue properties of steel wire; (part 2) on the effect of the total reduction by drawing and the low temperature annealing upon the longitudinal residual stress of cold drawn steel wire. Mater: Testing 9, 31-39 (in Japanese).
16. D. N. Kocanda, S. Kocanda and K. J. Miller (1996) Influence of shot peening on short crack behavior in medium carbon steel. Fatigue Fract. Engng Mater. Struct. 19, 911-917.
17. G. H. Farrahi, J. L. Lebrun and D. Couratin (1995) Effect of shot peening on residual stress and fatigue life of a spring steel. Fatigue Fract. Engng Mater. Struct. 18, 211-220.
18. T. Nishioka (1956) Residual stresses in drawn steel. J. Japan Inst. Metals 20, 424-427 (in Japanese).
19. H. Suto (1988) Residual Stresses and Distortion, Uchidarokakuho, Tokyo, p. 98 (in Japanese).
20. A. Yoshikawa and T. Sugeno (1965) Factors responsible for the sharp fatigue limit in iron and steel. Trans. Met. Soc. AIME 233, 1314-1317.
21. Y. Murakami and M. Shimizu (1988) Effects of nonmetallic inclusions, small defects and small cracks on fatigue strength of metals. Trans. Jpn. Soc. Mech. Engng A 54, 413-425 (in Japanese).
22. G. M. Sinclair, J. D. Morrow and A. S. Ross (1959) Tips on designing with residual stresses. SAE J. Sept., 76-77.