Thermal elastohydrodynamic model of a radial up seal-part I: Analysis and base results

Journal of Tribology

Volumn 121, Issue 1, 1999, Pages 1-10

  Day, Kevin ^a   Salant, Richard F ^a  

^a GEORGIA INSTITUTE OF TECHNOLOGY   (United States)

Author keywords

[No Author keywords available]

Indexed keywords

CAVITATION; DEFORMATION; ELASTIC MODULI; ELASTOHYDRODYNAMIC LUBRICATION; MATHEMATICAL MODELS; PRESSURE DISTRIBUTION; SHEAR STRESS; TEMPERATURE DISTRIBUTION; THERMAL EFFECTS; THERMODYNAMICS; VISCOSITY;

ASPERITIES DISTRIBUTION; RADIAL LIP SEAL;

SEALS;

LIP SEAL; MATHEMATICAL MODELING;

EID: 0033062042     PISSN: 07424787     EISSN: 15288897     Source Type: Journal    
DOI: 10.1115/1.2833803     Document Type: Article

References (20)

1. Elrod, H. G., 1981, “A Cavitation Algorithm,” ASME Journal of Lubrication Technology, Vol. 103, pp. 350-354.
2. Hayward, A. T. J., 1961, “Viscosity of Bubbly Oil,”Fluids Report, No. 99, National Engineering Laboratory.
3. Kammiiller, M., 1986, “Zur Abdichtwirkung von Radial-Wellendichtringen,” Dr.-Ing. thesis, Universität Stuttgart, Stuttgart.
4. Kang, Y. S., and Sadeghi, F., 1997, “Numerical Analysis of Temperature Distribution at the Lip Seal-Shaft Interface,” ASME Journal of Tribology, Vol. 119, pp. 273-278.
5. Kays, W. M., and Bjorklund, I. S., 1958, “Heat Transfer From a Rotating Cylinder With and Without Crossflow,”ASME Trans., Vol. 80, pp. 70-78.
6. MUller, H., 1987, “Concepts of Sealing Mechanism of Rubber Lip Type Rotary Shaft Seals,” Proceedings, 11th International Conference on Fluid Sealing, B. S. Nau, ed., BHRA, pp. 698-709.
7. Nakamura, K., and Kawahara, Y., 1984, “An Investigation of Sealing Properties of Lip Seals Through Observations of Sealing Surfaces Under Dynamic Condition,” Proceedings, 10th International Conference on Fluid Sealing, B. S. Nau, ed., BHRA, pp. 87-105.
8. Patankar, S. V., 1980, Numerical Heat Transfer and Fluid Flow, Hemisphere, New York.
9. Pinkus, O., 1990, Thermal Aspects of Fluid Film Tribology, ASME Press, New York.
10. Salant, R. F., 1992, “Numerical Analysis of the Flow Field Within Lip Seals Containing Microundulations,” ASME Journal of Tribology, Vol. 114, pp. 485-492.
11. Salant, R. F., 1996, “Elastohydrodynamic Model of the Rotary Lip Seal,” ASME Journal of Tribology, Vol. 118, pp. 292-296.
12. Salant, R. F., 1997, “Rotary Lip Seal Operation with an Ingested Meniscus,” ASME Journal of Tribology, Vol. 119, pp. 205-210.
13. Salant, R. F., and Flaherty, A. L., 1994, “Elastohydrodynamic Analysis of Reverse Pumping in Rotary Lip Seals with Microundulations,” ASME Journal of Tribology, Vol. 116, pp. 56-62.
14. Salant, R. F., and Flaherty, A. L., 1995, “Elastohydrodynamic Analysis of Reverse Pumping in Rotary Lip Seals with Microasperities,” ASME Journal of Tribology, Vol. 117, pp. 53-59.
15. Sponagel, S., Kilthau, G. and Spies, K., 1987, “Sealing Mechanisms of Lip Seals,”Proc. 11th Int. Conf. Fluid Sealing, K4, pp. 748-772.
16. Stakenborg, M., 1988, “On the Sealing and Lubrication Mechanism of Radial Lip Seals,” Ph.D. thesis, Eindhoven University of Technology.
17. Taylor, G. I., 1932, “Viscosity of a Fluid Containing Small Drops of Another Fluid,”Proc. Roy. Soc. Series A., Vol. 183, pp. 41-48.
18. van Leeuwen, H., and Wolfert, M., 1996, “The Sealing and Lubrication Principles of Plain Radial Lip Seals: An Experimental Study of Local Tangential Deformations and Film Thickness,”Leeds-Lyon Conference, Elastohydrodynatnics *96, D. Dowson et al., ed., Elsevier.
19. Yasutomi, S., Bair, S., and Winer, W.O., 1984, “An Application of a Free Volume Model to Lubricant Rheology I-Dependence of Viscosity on Temperature and Pressure,” ASME Journal of Tribology, Vol. 106, pp. 291-303.
20. Day, K., 1997, “Thermal Elastohydrodynamic Analysis of a Radial Lip Seal,” Masters thesis, Georgia Institute of Technology, Atlanta, Georgia.