Orbit induced journal temperature variation in hydrodynamic bearings

Journal of Tribology

Volumn 121, Issue 1, 1999, Pages 77-84

  Gomiciaga, R ^a   Keogh, P S ^a  

^a University of Bath   (United Kingdom)

Author keywords

[No Author keywords available]

Indexed keywords

BENDING (DEFORMATION); COMPUTATIONAL FLUID DYNAMICS; ELASTOHYDRODYNAMIC LUBRICATION; HEAT TRANSFER; INTERFACES (MATERIALS); MACHINE VIBRATIONS; ROTATIONAL FLOW; THERMAL EFFECTS;

THERMAL BENDING;

JOURNAL BEARINGS;

COMPUTATIONAL FLUID DYNAMICS; HEAT TRANSFER; HYDRODYNAMIC BEARING;

EID: 0033030570     PISSN: 07424787     EISSN: 15288897     Source Type: Journal    
DOI: 10.1115/1.2833814     Document Type: Article

References (16)

1. Andrisano, A. O., 1988, “An Experimental Investigation on the Rotating Journal Surface Temperature Distribution in a Full Circular Bearing,” ASME Journal of Tribology, Vol. 110, pp. 638-645.
2. Dimarogonas, A. D., 1970, “Packing Rub Effect in Rotating Machinery,” Dissertation, Rennselaer Polytechnic Institute, Troy, New York.
3. Fillon, M., and Khonsari, M. M., 1996, “Thermohydrodynamic Design Charts for Tilting-Pad Journal Bearings,” ASME Journal of Tribology, Vol. 118, pp. 232-238.
4. Gadangi, R. K., Palazzolo, A., and Kim, J., 1996, “Transient Analysis of Plain and Tilt Pad Journal Bearings Including Fluid Film Temperature Effects,” ASME Journal of Tribology, Vol. 118, pp. 423-430.
5. deJongh, F. M., and Morton, P. G., 1996, “The Synchronous Instability of a Compressor Rotor due to Bearing Journal Differential Heating,” ASME Journal of Engineering for Gas Turbines and Power, Vol. 118, pp. 816-823.
6. Keogh, P. S., and Morton, P. G., 1993, “Journal Bearing Differential Heating Evaluation with Influence on Rotor Dynamic Behaviour,” Proceedings Roy. Soc. (London), Series A, Vol. 441, pp. 527-548.
7. Keogh, P. S., and Morton, P. G., 1994, “The Dynamic Nature of Rotor Thermal Bending due to Unsteady Lubricant Shearing within a Bearing,” Proceedings Roy. Soc. (London), Series A, Vol. 445, pp. 273-290.
8. Khonsari, M. M., and Wang, S. H., 1992, “Notes on Transient THD Effects in a Lubricating Film,” STLE Tribology Transactions, Vol. 35, pp. 177-183.
9. Khonsari, M. M., Jang, J. Y., and Fillon, M., 1996, “On the Generalization of Thermohydrodynamic Analyses for Journal Bearings,” ASME Journal of Tribology, Vol. 112, pp. 571-579.
10. Lund, J. W., andTonnesen, J., 1984, “An Approximate Analysis of the Temperature Conditions in a Journal Bearing. Part II: Application,” ASME Journal of Tribology, Vol. 106, pp. 237-245.
11. Monmousseau, P., Fillon, M., and Frene, J., 1997, “Transient Thermoelastohy-drodynamic Study of Tilting-Pad Journal Bearings Under Dynamic Loading,” ASME Turbo Expo’97-Land, Sea and Air, Orlando, IGTI, Paper 97-GT-400.
12. Monmousseau, P., Fillon, M., and Frene, J., 1997, “Transient Thermoelastohy-drodynamic Study of Tilting-Pad Journal Bearings-Comparison Between Experimental Data and Theoretical Results,” ASME Journal of Tribology, Vol. 119, pp. 401-407.
13. Paranjpe, R. S., and Han, T., 1995, “A Transient Thermohydrodynamic Analysis Including Mass Conserving Cavitation for Dynamically Loaded Journal Bearings,” ASME Journal of Tribology, Vol. 117, pp. 369-378.
14. Patankar, S. V., 1980, Numerical Heat Transfer and Fluid Flow, McGraw-Hill, New York.
15. Tucker, P. G., and Keogh, P. S., 1996, “On the Dynamic Thermal State in a Hydrodynamic Bearing With a Whirling Journal Using CFD Techniques,” ASME Journal of Tribology, Vol. 112, pp. 356-363.
16. Van Doormaal, J. P., and Raithby, G. D., 1984, “Enhancement of the SIMPLE Method for Predicting Incompressible Fluid Flows,”Numerical Heat Transfer, Vol. 7, pp. 147-163.