Measurements of discharge coefficients in film cooling

Journal of Turbomachinery

Volumn 121, Issue 2, 1999, Pages 243-248

  Burd, S W ^a   Simon, T W ^a  

^a UNIVERSITY OF MINNESOTA   (United States)

Author keywords

[No Author keywords available]

Indexed keywords

COOLANTS; DISCHARGE (FLUID MECHANICS); FLOW MEASUREMENT; FLOW OF FLUIDS; GEOMETRY; STREAM FLOW; TURBINES;

DISCHARGE COEFFICIENT; FILM COOLING; FREE STREAM;

COOLING;

COOLING; DISCHARGE COEFFICIENT; FILM; WIND TUNNEL;

EID: 0032817569     PISSN: 0889504X     EISSN: 15288900     Source Type: Journal    
DOI: 10.1115/1.2841307     Document Type: Article

References (23)

1. Abramovich, G. N., 1963, The Theory of Turbulent Jets, English Translation by M.I.T. Press, Boston, MA.
2. Andrews, G. E., and Mkpadi, M. C., 1984, “Full-Coverage Discrete Hole Wall Cooling: Discharge Coefficients,” ASME Journal of Engineering for Gas Turbines and Power, Vol. 106, pp. 183-192.
3. Burd, S. W., Kaszeta, R. W., and Simon, T. W., 1996, “Measurements in Film Cooling Flows: Hole LID and Turbulence Intensity Effects,” ASME Paper No. 96-WA/HT-7; ASME Journal oh Turbomachinfry, Vol. 120, 1998, pp. 791 - 798.
4. Burd, S. W., and Simon, T. W., 1997, “The Influence on Film Cooling Supply Geometry on Film Coolant Exit and Surface Adiabatic Effectiveness,” ASME Paper No. 97-GT-25.
5. Byerley, A., 1989, “Heat Transfer Near the Entrance to a Film Cooling Hole in a Gas Turbine Blade,” Ph.D. Thesis, Department of Engineering Science, University of Oxford, UK.
6. Fried, E., and Idclchik, I.E., 1989, Flow Resistance: A Design Guide for Engineers, Hemisphere Publishing Corp., New York.
7. Gritsch, M., Schulz, A., and Wittig, S., 1998, “Discharge Coefficient Measurements of Film Cooling Holes With Expanded Exits,” ASME Journal of Turbomachinery, Vol. 120, pp. 557-564.
8. Haller, B. R., and Camus, J., 1984, “Aerodynamic Loss Penalty Produced by Film Cooling in Transonic Turbine Blades,” ASME Journal of Engineering For Gas Turbines and Power, Vol. 106, pp. 198-205.
9. Hay, N., Henshall, S. E., and Manning, A., 1994a, “Discharge Coefficients of Holes Angled to the Flow Direction,” ASME Journal oh Turuomachinery, Vol. 116, pp. 92-96.
10. Hay, N., and Lampard, D., 1995, “The Discharge Coefficient of Flared Film Cooling Holes,” ASME Paper No. 95-GT-I5.
11. Hay, N., and Lampard, D., 1998, “Discharge Coefficient of Turbine Cooling Holes: A Review,” ASME Journal or Turbomachinfry, Vol. 120, pp. 314-319.
12. Hay, N., Lampard, D., and Benmansour, S., 1983, “Effect of Crossflows on the Discharge Coefficient of Film Cooling Holes,” ASME Journal of Engineering for Gas Turbines and Power, Vol. 105, pp. 243-248.
13. Hay, N., Lampard, D., and Khaldi, A., 1994b, “The Coefficient of Discharge of 30 Degree Inclined Film Cooling Holes With Rounded Entries or Exits,” ASME Paper No. 94-GT-180.
14. Hay, N., and Spencer, A., 1992, “Discharge Coefficients of Cooling Holes With Radiused and Chambered Inlets,” ASME Journal of Turbomachinfry, Vol. 114, pp. 701-706.
15. Khaldi, A., 1987, “Discharge Coefficients of Film Cooling Holes With Rounded Entries or Exits,” Ph.D. Thesis, Univ. of Nottingham, UK.
16. Lichtarowiez, A., Duggins, R. K., and Markland, E., 1965, “Discharge Coefficients for Incompressible Non-cavitating Flow Through Long Orifices,” J. Mech. Eng. Science, Vol. 7, No. 2, pp. 210-219.
17. Rogers, T., and Hersh, A. S., 1975, “The Effect of Grazing Flow on the Steady State Resistance of Square-Edged Orifices,” AIAA Paper No. 75-493.
18. Rowbury, D. A., Oldfield, M. L. G., and Lock, G. D., 1997, “Engine Representative Discharge Coefficients Measured in an Annular Nozzle Guide Vane Cascade,” ASME Paper No. 97-GT-99.
19. Sasaki, M., Takahara, K., Sakata, K., and Kumsgui, T., 1976, “Study on Film Cooling of Turbine Blades,” JSME Bulletin, Vol. 19, No. 137, pp. 1344-1352.
20. Thole, K., Gritsch, M., Schulz, A., and Wittig, S., 1997, “Effect of a Crossflow at the Entrance to a Film-Cooling Hole,“ ASME Journal of Fluids Engineering, Vol. 119, pp. 537-540.
21. Tillman, E. S., and Jen, H. F., 1984, “Cooling Airflow Studies at the Leading Edge of a Film Cooled Airfoil,” ASME Journal of Engineering for Gas Turbines and Power, Vol. 106, pp. 214-221.
22. Walters, D. K., and Leylek, J. H., 1997, “A Detailed Analysis of Film-Cooling Physics: Part 1-Streamwise Injection With Cylindrical Holes,” ASME Paper No. 97-GT-269. '
23. Wang, L., 1996, “A Study of Gas Turbine Flows, Turbulence Generation, and Film Cooling Flow Measurement,” M.S. Thesis, Department of Mechanical Engineering, University of Minnesota.