Surface roughening and contact behavior in forming of aluminum sheet

Journal of Tribology

Volumn 121, Issue 2, 1999, Pages 224-233

  Lo, Sy Wei ^a   Horng, Tzu Chern ^a,b  

^a National Yuniin University of Science and Tecfinology   (Taiwan)

^b NATIONAL FORMOSA UNIVERSITY   (Taiwan)

Author keywords

[No Author keywords available]

Indexed keywords

ASPERITY; FRICTION; METAL WORKING; SHEET METAL; SURFACE ROUGHNESS;

ALUMINUM SHEET; FAST FOURIER TRANSFORMS; INTERFACES (MATERIALS); METAL FORMING; PLASTIC DEFORMATION; STRAIN; STRAIN RATE; SURFACE ROUGHNESS;

ASPERITY FLATTENING; PLASTIC STRAIN;

TRIBOLOGY;

EID: 0032814273     PISSN: 07424787     EISSN: 15288897     Source Type: Journal    
DOI: 10.1115/1.2833925     Document Type: Article

References (20)

1. Christensen, H., and Tonder, K., 1971, “The Hydrodynamic Lubrication of Rough Bearing Surfaces of Finite Width,” ASME Journal of Lubrication Technology, July, pp. 324-330.
2. Dai, Y. Z., and Chiang, F. P., 1992, “On the Mechanism of Plastic Deformation Induced Surface Roughness,” ASME Journal of Engineering Materials and Technology, Vol. 114, Oct., pp. 432-438.
3. Dautzenberg, J. H., and Kals, J. A. G., 1984, “Stress State and Surface Roughness,”Advanced Technology of Plasticity, Vol. 1, pp. 186.
4. Dautzenberg, J. H., and Kals, J. A. G., 1985, “Surface Roughness Caused by Metal Forming,”Annals of the CIRP, Vol. 34/1, pp. 477-479.
5. Howser, B., 1991, “A Micromechanical Model for Boundary Friction and Surface Topography Evolution in Strip Rolling,” PhD Thesis, Northwestern University, Evanston, IL.
6. Kaga, H., 1971, “Micro-Geometric Variation of Surface Profile in Sheet Metal Forming,”Annals of the CIRP, Vol. 20/1, pp. 55-56.
7. Klimczak, T., Dautzenberg, J. H., and Kals, J. A. G., 1988, “On the Roughening of a Free Surface During Sheet Metal Forming,”Annals of the CIRP, Vol. 37/1, pp. 267-270.
8. Korzekwa, D. A., Dawson, P. R., and Wilson, W. R. D., 1992, “Surface Asperity Deformation During Sheet Forming,”Int. J. Mech. Sci., Vol. 34, pp. 512-540.
9. Osakada, K., and Oyane, M., 1971, “On the Roughening of Free Surface in Deformation Process,”Bulletin of the JSME, Vol. 14, pp. 171-177.
10. Parmar, A., and Mellor, P. B., 1977, “A New Model for the Prediction of Instability and Limit Strains in Thin Sheet Metal,”Int. J. Mech. Sci., Vol. 19, pp. 389-398.
11. Saha, P. K., and Wilson, W. R. D., 1994, “Influence of Plastic Strain on Friction in Sheet Metal Forming,”Wear, Vol. 172, pp. 167-173.
12. Shih, H.-C., Wilson, W. R. D., and Saha, P. K., 1996, “Modeling the influence of Plastic Strain on Boundary Friction in Sheet Metal Forming,” NAMRC Trans. (SME), pp. 173-180.
13. Struik, K. G., and Prakash, A., 1980, “Surface Roughness: The Measurement of Deformed Surfaces,” Int. J. Prod. Res., No. 5, pp. 559-569.
14. Takakura, N., Yamaguchi, K., and Kitagawa, M., 1995, “Suppression of Free Surface Roughening of Metal with Plastic Deformation,”JSME Int. J., Series C, Vol. 38, No. 4, pp. 824-830.
15. Thomson, P. F., and Nayak, P. U., 1980, “The Effect of Plastic Deformation on the Roughening of Free Surfaces of Sheet Metal,”Int. J. of Mach. Tool Des. Res., Vol. 20, pp. 73-86.
16. Thomson, P. F., and Shafer, B, V., 1982, “The Roughening of Free Surfaces during Plastic Working,”Int. J. Mach. Tool Des. Res., Vol. 22, No. 4, pp. 261.
17. von Stebut, J., 1986, “Modification of Surface Profile’s Height Parameters During Strip Drawing,”Wear, Vol. 109, pp. 145-155.
18. Wilson, W. R. D., 1991, “Friction Models for Metal Forming in the Boundary Lubrication Regime,” ASME Journal of Engineering Materials and Technology, Vol. 113, pp. 60-68.
19. Wilson, W. R. D., and Chang, D. F., 1996, “Low Speed Mixed Lubrication of Bulk Metal Forming Processes,” ASME Journal of Tribology, Vol. 118, No. 1, pp. 83-89.
20. Wilson, W. R. D., and Sheu, S., 1988, “Real Area of Contact and Boundary Friction in Metal Forming,”Int. J. Mech. Sci., Vol. 30, No. 7, pp. 475-489.