Evaluation of the adjusted compliance ratio technique for determining the effective stress intensity factor

ASTM Special Technical Publication

Volumn , Issue 1332, 1999, Pages 674-695

  Donald, J Keith ^a   Bray, Gary H ^b   Bush, Ralph W ^b  

^a Fracture Technology Associates   (United States)

^b NONE

Author keywords

[No Author keywords available]

Indexed keywords

ALUMINUM ALLOYS; CRACK PROPAGATION; ESTIMATION; FATIGUE OF MATERIALS; GEOMETRY; STRAIN; STRESS CONCENTRATION; TENSILE PROPERTIES;

ADJUSTED COMPLIANCE RATIO; COMPACT TENSION; CRACK CLOSURE; MIDDLE CRACK TENSION;

STRESS INTENSITY FACTORS;

EID: 0032674919     PISSN: 10403094     EISSN: None     Source Type: Conference Proceeding    
DOI: 10.1520/stp14977s     Document Type: Article

References (12)

1. Donald, J. K., "A Procedure for Standardizing Crack Closure Levels", Mechanics of Fatigue Crack Closure, ASTM STP 982, J. C. Newman, Jr. and W. Elber, Eds., American Society for Testing and Materials, 1988, pp. 222-229.
2. max ΔK-Decreasing Fatigue Crack Growth Procedures," Small Crack Test Methods, ASTM STP 1149, J. M. Larsen and J. E. Allison, Eds., American Society for Testing and Materials, 1992, pp. 197-220.
3. Donald, J. K., "Introducing the Compliance Ratio Concept for Determining Effective Stress Intensity," presented at the First International Conference on Fatigue Damage in Structural Materials, Hyannis, MA, September 1996 (to be published in International Journal of Fatigue).
4. Elber, Wolf, "The Significance of Fatigue Crack Closure," Damage Tolerance in Aircraft Structures, ASTM STP 486, American Society for Testing and Materials, 1971, pp. 230-242.
5. Hertzberg, R. W., Newton, C. H. and Jaccard, R., "Crack Closure: Correlation and Confusion," Mechanics of Fatigue Crack Closure, ASTM STP 982, American Society for Testing and Materials, 1988, pp. 139-148.
6. Phillips, E. P., "Results of the Round Robin on Opening-Load Measurement," NASA Technical Memorandum 101601, 1989, Langley Research Center, Hampton Virginia.
7. Phillips, E. P., "Results of the Second Round Robin on Opening-Load Measurement," NASA Technical Memorandum 109032, 1993, Langley Research Center, Hampton Virginia.
8. Sadananda, K. and Vasudevan, A. K., "Analysis of Fatigue Crack Closure and Thresholds," Fracture Mechanics: 25th Volume, ASTM STP 1220, Erdogan and Hartranft, Eds., American Society for Testing and Materials, Philadelphia, PA, 1995.
9. Sadananda, K. and Vasudevan, A. K., "Short Crack Growth Behavior," Fatigue and Fracture Mechanics: 27th Volume, ASTM STP 1296, Piascik, R., Dowling, N., Newman, J., American Society for Testing and Materials, West Conshohocken, PA, 1997.
10. Chen, D. L., Weiss, B. and Stickler, R., "Contribution of the Cyclic Loading Portion Below the Opening Load to Fatigue Crack Growth", Materials Science and Engineering, A208, 1996, pp. 181-187.
11. Donald, J. K., "A Perspective on the ASTM Standard for Measurement of Fatigue Growth Rates: Past, Present and Future," ASTM Committee E-8 1997 Fatigue Lecture, May 6, 1997, St. Louis, Missouri.
12. Donald, J. K. and Schmidt, D. W., "Computer-Controlled Stress Intensity Gradient for High Rate Fatigue Crack Growth Testing," Journal of Testing and Evaluation, JTEVA, Vol. 8, No. 1, Jan 1980, pp. 19-24.