Effect of tool edge geometry on workpiece sub-surface deformation and through-thickness residual stresses for hard-turning of AISI 52100 steel

Technical Paper - Society of Manufacturing Engineers. MR

Volumn , Issue MR99-167, 1999, Pages 1-6

  Thiele, Jeffrey D ^a   Melkote, Shreyes N ^a  

^a GEORGIA INSTITUTE OF TECHNOLOGY   (United States)

Author keywords

[No Author keywords available]

Indexed keywords

CERAMIC CUTTING TOOLS; COMPRESSIVE STRESS; CUBIC BORON NITRIDE; HONING; PLASTIC FLOW; POLYCRYSTALLINE MATERIALS; RESIDUAL STRESSES; STRESS ANALYSIS; TURNING;

HARD TURNING; STEEL 52100;

STEEL;

EID: 0032653748     PISSN: None     EISSN: None     Source Type: Journal    
DOI: None     Document Type: Article

References (18)

1. Konig, W., Berktold, A., Kock, K-F. (1993) "Turning versus Grinding - A Comparison of Surface Integrity Aspects and Attainable Accuracies", Annals of the CIRP, Vol. 42, pp. 39-43.
2. Vyas, A., Shaw, M.C. (1997) "Chip Formation When Hard Turning Steel", Mfg. Sci. and Tech., ASME, MED-Vol. 6-2, pp. 21-28.
3. Davies, M. A., Chou, Y., and Evans, C. J. (1996) "On Chip Morphology, Tool Wear, and Cutting Mechanisms in Finish Hard Turning", Mfg. Sci. and Eng., ASME MED-Vol. 4, pp. 237-242.
4. El-Wardany, T.I., and Elbestawi, M.A. (1998) "Phenomenological Analysis of Material Side Flow in Hard Turning: Causes, Modeling, and Elimination," in Proc. of the CIRP Workshop on Modeling of Machining Operations, Atlanta, GA, pp. 2A/5-1.
5. Matsumoto, Y., Barash, M.M., Liu, C.R. (1986) "Effect of Hardness on the Surface Integrity of AISI 4340 Steel", ASME J. of Eng. for Ind., Vol. 108, pp. 169-175.
6. Wu, D.W., Matsumoto, Y. (1990) "The Effect of Hardness on Residual Stresses in Orthogonal Machining of AISI 4340 Steel", ASME J. of Eng. for Ind., Vol. 112, pp. 245-252.
7. Brinksmeier, E., Cammett, J.T., Konig, W., Leskovar, P., Peters, J., Tonshoff, H.K. (1982) "Residual Stresses -Measurement and Causes in Machining Processes". Annals of the CIRP, Vol. 31, pp. 491-510.
8. Chou, Y. K., Evans, C. J. (1997) "White Layers and Thermal Modeling of Hard Turned Surfaces", Mfg. Sci. and Tech., MED-Vol. 6-2, pp. 75-82.
9. Griffiths, B.J. (1987) "Mechanisms of White Layer Generation With Reference to Machining Processes and Deformation Processes", J. of Tribology, July, Vol. 109, pp. 525-530.
10. Aspinwall, D. K, Abrao, A. M. and Wise, M. L. H. (1995) "Tool Life and Workpiece Surface Integrity Evaluations When Machining Hardened AISI 52100 Steels With Conventional Ceramic and PCBN Tool Materials". SME Technical Paper, MR95-159, pp. 1-9.
11. Abrao, A.M., Aspinwall, D.K. (1996) "The Surface Integrity of Turned and Ground Hardened Bearing Steel", Wear, Vol. 196, pp. 279-284.
12. Tonshoff, H. K., Wobker, H-G., Brandt, D. (1995) "Hard Turning - Influences on Workpiece Properties", Trans. of NAMRI/SME, Vol. XXIII, pp. 215-220.
13. Chou, Y. K., Evans C. J. (1997) "Finish Hard Turning of Powder Metallurgy M50 Steel", Trans. of NAMRI/SME, Vol. XXV, pp. 81-86.
14. Sista, P. S., Swain, S. O., Srinivasan, C., Farris, T. N. (1997) "Tool Wear Characteristic of CBN Tools in the Finish Machining of Tool Steels", Mfg. Sci. and Tech., ASME, MED-Vol. 6-2, pp. 161-168.
15. Jang, D.Y., Watkins, T.R., Kozaczek, K.J., Hubbard, C.R., Cavin, O.B., 1996, "Surface Residual Stresses in Machined Austenitic Stainless Steel", Wear, 1, Vol. 194, pp. 168-173.
16. Liu, C.R., Barash, M.M., 1982, "Variables Governing Patterns of Mechanical Residual Stress in a Machined Surface", ASME J. of Eng. for Ind., Vol. 104, pp. 257-264.
17. Thiele, J.D., "An Investigation of Surface Generation Mechanisms for Finish Hard Turning of AISI 52100 Steel," M.S. Thesis, August 1998, Georgia Institute of Technology, Atlanta, GA.
18. Noyan, I.C., Cohen, J.B., Residual Stress Measurement by Diffraction and Interpretation, Springer-Verlag, New York, 1987.