Modeling tool stresses and temperature evaluation in turning using finite element method

Machining Science and Technology

Volumn 2, Issue 2, 1998, Pages 355-367

  Chandrasekaran, H ^a   Thuvander, A ^a  

^a SWEREA KIMAB   (Sweden)

Author keywords

[No Author keywords available]

Indexed keywords

CUTTING TOOLS; FINITE ELEMENT METHOD; FRICTION; MATHEMATICAL MODELS; PHASE TRANSITIONS; SHEAR STRESS; STRESS ANALYSIS; TEMPERATURE DISTRIBUTION; THERMOELASTICITY;

BINDER PHASE TRANSFORMATION (BPT) TECHNIQUE; TOOL STRESSES;

TURNING;

EID: 0032294181     PISSN: 10910344     EISSN: None     Source Type: Journal    
DOI: 10.1080/10940349808945676     Document Type: Article

References (17)

1. K. F. Ehmann, S. G. Kapoor, R. E. DeVor, and I. Lazoglu, "Machining Process Modelling: A Review," J. Manufac. Sci, and Engrg., 119 (1997) 655-663.
2. W. J. Endres, R. E. DeVor, and S. G. Kapoor, "A Dual-Mechanism Approach to the Prediction of Machining Forces, Parts 1 and 2," J. Engrg. for Industry, 117 (1995) 526-541.
3. D. Haslam and C. Rubenstein, "Surface and Sub-Surface Work-Hardening Produced by Planning Operation," Annals of CIRP, 18(1) (1970) 369-381.
4. T. Obikawa, H. Sasahara, T. Shirakashi, and E. Usui, "Application of Computational Machining Method to Discontinuous Chip Formation," J. Manuf. Sci. and Engrg., 119 (1997) 667-674.
5. I. S. Jawahir and C. A. van Luttervelt, "Recent Developments in Chip Control Research and Development," Annals of CIRP, 42(2) (1993) 659.
6. J. S. Strenkowski and S. M Athavale, "A partially Constrained Eulerian Orthogonal Cutting Model for Chip Control Tools," J. Manuf. Sci. and Engrg., 119 (1997) 681-688.
7. J. A. Arsecularatne, R. F. Fowle, and P. Mathew, "Prediction of Chip Flow Direction, Cutting Forces and Surface Roughness in Finish Turning," J. Manuf. Sci. and Engrg., 120 (1998) 1-12.
8. R. Natarajan and S. Jeelani, "Residual Stresses in Machining Using Finite Element Method," Computers in Engineering, Computer Software and Applications (1983) 79.
9. H. Chandrasekaran, A. Thuvander, and H. Wisell, "Estimation of Cutting Forces, Contact Loads and Elastic Stress Field in a HSS Tool during Single Tooth Peripheral Milling," Report from Swedish Institute for Metals Research, Stockholm, Im-2194 (1985).
10. N. N. Zorev, "Interrelationship Between Shear Process Occurring Along Tool Face and on Shear Plane in Metal Cutting," Int. Res. in Production Engrg., 42-49.
11. W. Katwinkel, "Untersuchungen an Schneiden Spanender Werkzeuge mit Hilfe deer Spannungsoptik," Ind. Anz., May (36) (1957) 525-532.
12. H. Chandrasekaran and D. V. Kapoor, "Photoelastic Analysis of Tool-Chip Interface Stresses," J. Engrg. for Industry, 86 (1965) 495-502.
13. A. Bagchi and P. K. Wright, "Stress Analysis in Machining Using Sapphire Tools," Proc., Royal Soc. of London (1986).
14. H. Chandrasekaran, J. O. Johansson, and A. Thuvander, "The Influence of Cutting Fluid on Tool Temperature Distribution in Single Point Turning of Steel," Report from Swedish Institute for Metals Research, IM-3587, Stockholm, Sweden (1998).
15. T. H. Childs, K. Maekawa, and P. Maulik, "Effect of Coolant on Temperature Distribution in Metal Machining," Mat. Sci. and Technol, 14 (1984) 1006-1016.
16. A. Thuvander, A. Nordgren, and H. Chandrasekaran, "Measurement and FEM Calculation of Temperature Distribution in Cemented Carbide during Turning of Quenched and Tempered Steel," Report from Swedish Institute for Metals Research IM-3244, Stockholm, Sweden (1995).
17. H. Chandrasekaran and R. Nagarajan, "Influence of Flank Wear on the Stresses in the Cutting Tool," J. Engrg. for Industry, (1977) 566-578.