Study on the thermo-elastic-plastic cutting model for 3-D tool with chip breaker

Journal of Engineering Materials and Technology, Transactions of the ASME

Volumn 120, Issue 4, 1998, Pages 265-274

  Lin, Zone Ching ^a   Zheng, Yan Liang ^a  

^a NATIONAL TAIWAN UNIVERSITY OF SCIENCE AND TECHNOLOGY   (Taiwan)

Author keywords

[No Author keywords available]

Indexed keywords

ALGORITHMS; ELASTOPLASTICITY; FINITE DIFFERENCE METHOD; FINITE ELEMENT METHOD; MATHEMATICAL MODELS; RESIDUAL STRESSES; STRAIN RATE; STRESS ANALYSIS; THERMOELASTICITY;

CHIP BREAKER; LAGRANGIAN FORMULATION;

METAL CUTTING;

EID: 0032179167     PISSN: 00944289     EISSN: 15288889     Source Type: Journal    
DOI: 10.1115/1.2807011     Document Type: Article

References (14)

1. Hashemi, J., Tseng, A. A., and Chou, P. C, 1994, “Finite Element Modeling of Segmental Chip Formation in High Speed Orthogonal Cutting,” J. Materials Engineering & Performance, Vol. 3, No. 6, pp. 712-721.
2. Iwata, K., Osakada, K., and Terasaka, T., 1984, “Process Modeling of Orthogonal Cutting by the Rigid-Plastic Finite Element Method,” ASME JOURNAL OF ENQINEERINQ MATERIALS AND TECHNOLOGY, Vol. 106, pp. 132-138.
3. Liu, C. R., and Barash, M. M., 1976, “The Mechanical State of the Sublayer of a Surface Generated By Chip Removal Process, Part 2; Cutting with a Tool with Flank Wear,” ASME Journal of Engineering for Industry, Vol. 98, pp. 1102-1108.
4. Lin, Z. C, and Lin, S. Y., 1990, “An Investigation of a Coupled Analysis of A Thermo-Elastic-Plastic Model During Warm Upseting,” Int. J. Mach. Tool Mantrfact., Vol. 30, No. 4, pp. 599-612.
5. Lee, E. H., and Shaffer, B. W., 1951, “The Theory of Plasticity Applied to a Problem of Machining,” ASME Journal cf Applied Mechanics, Vol. 18, pp. 405-413.
6. Maekawa, K., Nagayama, I., Ohshima, I., and Murata, R., 1990, “Finiye Element Simulation of Oblique Cutting,” Bull. Japan Soc. Of Free. Engrg., Vol. 24, No. 33, pp. 221-222.
7. Merchant, M. E., 1945, “Mechanics of the Metal Cutting Process,” J. Appl. Phys., Vol. 16, pp. 267-318.
8. Sasahara, H., Obikwa, T., and Shirakashi, T., 1993, “FEM Analysis on Three Dimensional Cutting-Analysis on Large Deformation Problem of Tool Entry,” JSPE, Vol. 59, No. 8, pp. 1275-1280.
9. Shirakashi, T., Maekawa, K., and Usui, E., 1983, “Flow Stress of Low Carbon Steel at High Temperature and Strain Rate,” Bull. Japa Soc. Prec. Engrg., Vol. 17, pp. 167-172.
10. Strenkowski, J. S., and Carroll J. T., 1990, “A Finite Element Model of Orthogonal Metal Cutting,” ASME Journal of Engineering for Industry, Vol. 127, pp. 313-318.
11. Obikawa, T., Sasahara, H., and Usui, E., 1992, “Finite Element Approach to Chip Breaker,” JSPE-58-12 ‘92-12-2051, pp. 107-112.
12. Usui, E., Maekawa, K., and Shirakashi, T., 1981, “Simulation Analysis of Built-up Edge Formation in Machining of Low Carbon Stell,” Bull. Japan Soc. Of Prec. Eng., Vol. 15, No. 4, pp. 237-242.
13. Ueda, K., and Manabe, K., 1993, “3-Dimensional Rigid-Plastic Fern Simulation of Chip Formation Process,” Int. Pro. In Precision Engineer, Butter Worth Heinimann, pp. 113-124.
14. Yamada, Y., 1980, Visco-Elasticity Plasticity, Baifukan, Japan.