Friction and wear behavior of Cu-Fe3Al powder metallurgical composites in dry sliding

Wear

Volumn 220, Issue 1, 1998, Pages 72-79

  Tu, J P ^a,b   Meng, L ^a   Liu, M S ^a  

^a ZHEJIANG UNIVERSITY   (China)

^b HIROSHIMA UNIVERSITY   (Japan)

Author keywords

Coefficient of friction; Composite; Fe3Al; Oxide film; Powder metallurgy

Indexed keywords

COPPER POWDER METALLURGY; ENERGY DISPERSIVE SPECTROSCOPY; FRICTION; IRON ALLOYS; METALLIC MATRIX COMPOSITES; PRESSURE EFFECTS; PROTECTIVE COATINGS; SCANNING ELECTRON MICROSCOPY; STRAIN HARDENING; VOLUME FRACTION; WEAR RESISTANCE;

DRY SLIDING; FRICTION COEFFICIENT;

COPPER ALLOYS;

COMPOSITE; COPPER ALLOY; DRY SLIDING; FRICTION; WEAR;

EID: 0032172786     PISSN: 00431648     EISSN: None     Source Type: Journal    
DOI: 10.1016/S0043-1648(98)00243-9     Document Type: Article

References (22)

1. [1] J.D. Verhoeven, F.A. Schmidt, E.D. Gibson, W.A. Spitzig, Copper-refractory metal alloys, J. Metals, September, 1986, 20-24.
2. [2] H.L. Downing, J.D. Verhoeven, E.D. Gibson, The emissivity of etched Cu-Nb in situ alloys, J. Appl. Phys. 61 (7) (1987) 2621-2625.
3. [3] P.D. Funkenbusch, T.H. Courtney, D.G. Kubisch, Fabricability of and microstructural development in cold worked metal matrix composites, Scripta Metall. 18 (1984) 1099-1104.
4. [4] Z. Chen, P. Liu, J.D. Verhoeven, E.D. Gibson, Sliding wear behavior of deformation-processed Cu-15 vol.% Cr in situ composites, Wear 195 (1-2) (1996) 214-222.
5. [5] N. Saka, D.P. Karalekas, Friction and wear of particle-reinforced metal ceramic composites, The Inter. Conf. on Wear of Materials, Canada, April, 1985, 784-793.
6. [6] D. Nath, S.K. Biswas, P.K. Rohatgi, Wear characteristics and bearing performance of aluminum-mica particulate composite material, The Inter. Conf. on Wear of Materials, New York, 1979, 161-167.
7. [7] K. Anard, Kishore, On the wear of aluminum-corundum composites, Wear 85 (1983) 163-169.
8. [8] W. Simm, S. Freti, Abrasive wear of multiphase materials, Wear 129 (1989) 105-121.
9. [9] F.M. Hosking, F.F. Portillo, R. Wunderlin, R. Mehrabian, Composites of aluminum alloy: fabrication and wear behavior, J. Material Science 17 (1982) 477-498.
10. [10] A. Banerji, S.V. Prasad, M.K. Surappa, P.K. Rohatgi, Abrasive wear of cast aluminum alloy-zircon particle composites, Wear 82 (1982) 141-151.
11. [11] A. Alahelisten, F. Bergman, M. Oisson, S. Hogmark, On the wear of aluminum and magnesium meal matrix composites, Wear 165 (1993) 221-226.
12. [12] J. Fohl, T. Weissenbery, J. Wiedemeyer, General aspects for tribological applications of hard particle coatings, Wear 130 (1989) 275-288.
13. 3-A1 composites produced by centrifugal force infiltration, Materials Science and Technology 12 (1996) 483-488.
14. [14] M. Roy, B. Venkataraman, V.V. Bhanuprasad, Y.R. Mahajan, G. Sundarajan, The effect of paniculate reinforcement on the sliding wear behavior of aluminum matrix composites, Metall. Trans. 23 A (1992) 2833-2847.
15. [15] M.A. Zam Zam, Adhesive wear of hard particles reinforced metal-matrix powder composites, Metallurgy 43 (1989) 1158-1161.
16. [16] A.T. Alpas, J.D. Embury, Sliding and abrasive wear behavior of an aluminum (2014)-SiC particle reinforced, Scripta Metall. et Mater. 24 (1990) 931-935.
17. [17] A. Jokinen, P. Andersson, Tribological properties of PM aluminum alloy matrix composites, in: E.R. Andreotti, P.J. McGeehan (Eds.), Advance in Powder Metallurgy, Vol. 2, Metal Powder Industries Federation, Princeton, NJ, 1990, pp. 517-530.
18. 3Al, Wear 159 (1992) 241-247.
19. [19] H.E. Maupin, R.D. Wilson, J.A. Hawk, Wear deformation of ordered Fe-Al intermetallic alloys, Wear 162-164 (1993) 432-440.
20. 3Al alloy, Wear 209 (1997) 31-36.
21. [21] P. Liu, S. Bahadur, J.D. Verhoeven, Further investigation on the tribological behavior of Cu-20% Nb in situ composite, Wear 162-164 (1993) 211-219.
22. [22] J.K. Lancaster, The formation of surface films at the transition between mild and severe metallic wear, Proc. R. Soc. London, Ser. A. 273 (1962) 466-483.