Shrinkage anisotropy in fiber reinforced injection molded products

Polymer Composites

Volumn 19, Issue 4, 1998, Pages 325-334

  Jansen, K M B ^a   Van Dijk, D J ^a   Freriksen, M J A ^a  

^a UNIVERSITY OF TWENTE   (Netherlands)

Author keywords

[No Author keywords available]

Indexed keywords

ANISOTROPY; FIBER REINFORCED PLASTICS; INJECTION MOLDING; MATHEMATICAL MODELS; PRESSURE EFFECTS; RESIDUAL STRESSES; SHRINKAGE;

CLOSED-FORM EXPRESSIONS;

PLASTIC PRODUCTS;

EID: 0032131683     PISSN: 02728397     EISSN: None     Source Type: Journal    
DOI: 10.1002/pc.10105     Document Type: Article

References (23)

1. S. G. Advani, ed., Flow and Rheology in Polymer Composites Manufacturing, Composite Materials Series Vol. 10, Ch. 6 and 11, Elsevier Science, Amsterdam (1994).
2. S, G. Advani and C. L. Tucker III, SPE Antec Tech, Papers, 31, 1113 (1985).
3. S. G. Advani and C. L. Tucker III, J. Rheol, 31, 751 (1987).
4. C. L. Tucker III, J. Non-Newtonian Fluid Mech., 39, 239 (1991).
5. S. G. Advani and C. L. Tucker III, Polym, Compos., 13, 317 (1992).
6. J. S. Cintra and C. L. Tucker III, J. Rheol, 39, 1095 (1995).
7. T. Matsuoka et al., Polym. Eng. Sci, 30, 957 (1990).
8. M. Gupta and K. K. Wang, SPE Antec Tech. Papers, 39, 2290 (1993).
9. L. G. Reifscheider and H. U. Akay, Polym. Compos., 15, 261 (1994).
10. Z. Yu, J. Brisson, and A. Ait-Kadi, Polym. Compos., 15. 64 (1994).
11. M. Xia et al., Int. Polym. Processing, X. 74 (1995).
12. Ashton, Halpin, and Petit, Primer on Composite Materials, Technomic Pub. Co., Lancaster, Pa. (1969).
13. R. McCullough, Delaware Composites Design Encyclopedia-Vol.2: Micromechanical Materials Modeling, Technomic Pub. Co., Lancaster, Pa. (1990).
14. K. M. B. Jansen and G. Titomanlio, Polym. Eng. Sci, 36, 2029 (1996).
15. K. M. B. Jansen, D. J. van Dijk, and M. H. Husselman, Polym. Eng. Sci, accepted for publication.
16. R. S. Bay and C. L. Tucker III, Polym. Eng. Sci, 32, 240 (1992).
17. M. J. A. Freriksen and M. J. Schnitzler, Master's thesis. Twente University. The Netherlands (1996).
18. K. M. B. Jansen. Exp. Mechanics, 37, (September 1997).
19. M. R. Kamal and P. Singh, SPE Antec Tech. Papers, 35, 240 (1989).
20. R. P. Hegler and G. Mennig, Polym. Eng. Sci, 25, 395 (1985).
21. T. D. Papathanasiou, Int. Polymer Processing, XI, 275 (1996).
22. R. S. Bay and C. L. Tucker III, Polym. Compos., 13, 332 (1992)
23. M. P. I. M. Eijpe, PhD thesis, Twente University, The Netherlands (1997).