Effects of welding distortions and residual stresses on the ultimate strength of long rectangular plates under uniaxial compression

Marine Structures

Volumn 11, Issue 6, 1998, Pages 251-269

  Cui, Weicheng ^a   Mansour, Alaa E ^b  

^a CHINA SHIP SCIENTIFIC RESEARCH CENTER   (China)

^b UNIVERSITY OF CALIFORNIA   (United States)

Author keywords

Elastic large deflection analysis; Initial welding distortion shape; Residual stresses; Rigid plastic analysis; Ultimate compressive strength; Unstiffened plates

Indexed keywords

COMPRESSIVE STRENGTH; DEFLECTION (STRUCTURES); ELASTICITY; NUMERICAL ANALYSIS; RESIDUAL STRESSES; WELDING;

WELDING DISTORTIONS;

PLATES (STRUCTURAL COMPONENTS);

WELDING;

EID: 0032128795     PISSN: 09518339     EISSN: None     Source Type: Journal    
DOI: 10.1016/S0951-8339(98)00012-4     Document Type: Article

References (24)

1. [1] Guedes Soares C. Design equation for ship plate elements under uniaxial compression. J Construct Steel Res 1992;22:99-114.
2. [2] Ueda Y, Tall L. Inelastic buckling of plates with residual stresses. Publications International Association of Bridge and Structural Engineer, 1967:211-53.
3. [3] Mansour AE. Post-buckling behaviour of stiffened plates with small initial curvature under combined loads. Int shipbuild progr vol.18, June 1971.
4. [4] Hsu PH, Wu YS, editors. Proc 11th Int Ship and Offshore Structures Congr. Wuxi, China, 1991.
5. [5] Jeffrey NE, Kendrick AM, editors. Proc 12th Int Ship and Offshore Structures Congr. St. John's Canada, 1994.
6. [6] Faulkner D. A review of effective plating for use in the analysis of stiffened plating in bending and compression. J Ship Res 1975;19(1):1-17.
7. [7] Kmiecik M. A review of fabrication distortion tolerances for ship plating in the light of the compressive strength of plates. Lloyd's register technical association. Paper No.6, 1976.
8. [8] Frieze PA, Dowling PJ, Hobes RH. Ultimate load behaviour of plates in compression. In: Steel plated structures. London: Crosby Lockwood Staples 1977:24-50.
9. [9] Harding JE, Hobes RE, Neal BG. The elasto-plastic analysis of imperfect square plates under in-plane loading. Proc Inst Civil Engrs Part 2, vol. 63. 1979:137-58.
10. [10] Carlsen CA, Czujko J. The specification of tolerances for post-welding distortions of stiffened plates in compression. Struct Eng 1978;56A(5).
11. [11] Dow RS, Smith CS. Effects of localised imperfections on the compressive strength of long rectangular plates. J Construct Steel Res 1983;3:51-76.
12. [12] Ueda Y, Yao T. The influence of complex initial deflection modes on the behaviour and ultimate strength of rectangular plates in compression. J Construct Steel Res 1985;5.
13. [13] Guedes Soares C, Kmiecik M. Simulation of the ultimate compressive strength of an unstiffened rectangular plates. Marine Struct 1993;6:553-69.
14. [14] Paik JK, Pedersen PT. A simplified method for predicting ultimate compressive strength of ship panels. Int Shipbuild Progr 1996;43(434):139-57.
15. [15] Cui WC, Mansour AE. Generalization of a simplified method for predicting ultimate compressive strength of ship panels. Int Shipbuild Progr, accepted.
16. [16] Murray NW. Analysis and design of stiffened plates for collapse load. Struct Eng 1975;53:153-8.
17. [17] Rhodes J. On the approximate prediction of elasto-plastic plate behaviour. Proc Inst Civil Engrs Part 2, 1981;65:165-83.
18. [18] Hughes OF. Ship structural design: a rationally-based, computer-aided optimization approach. New York: Wiley, 1983.
19. [19] Carlsen CA. Simplified collapse analysis of stiffened plates. Norw Marit Res 1977;7(4):2-36.
20. [20] Smith CS, Davidson PC, Chapman JC, Dowling PJ. Strength and stiffness of ship's plating under in-plane compression and tension. Trans RINA 1988;130.
21. [21] Ueda Y, Yao T, Nakacho K, Yuan MG. Prediction of welding residual stress, deformation and ultimate strength of plate panels. In: Engineering design in welded constructions. Oxford: Pergamon Press 1992:251-9.
22. [22] Guedes Soares C, Faulkner D. Probabilistic modeling of the effect of initial imperfections on the compressive strength of rectangular plates. Proc. 3rd Int Symp on Practical Design of Ships and Mobile Units (PRADS). Trondheim 1987;2:783-95.
23. [23] Guedes Soares C, Gordo JM. Collapse strength of rectangular plates under transverse compression. J Construct Steel Res 1996;36(3):215-34.
24. [24] Guedes Soares C, Kmiecik M. In: Graczyk T, Jastrzebski T, Brebbia CA, Burns R, editors. Influence of the boundary conditions on the collapse strength of square plates with initial imperfections, marine Technology and Transportation Conference. Computational Mechanics Publications, 1995:227-35.