A tool deflection compensation system for end milling accuracy improvement

Journal of Manufacturing Science and Engineering, Transactions of the ASME

Volumn 120, Issue 2, 1998, Pages 222-229

  Yang, M Y ^a   Choi, J G ^a  

^a Korea Advanced Institute of Science and Technology (KAIST)   (South Korea)

Author keywords

[No Author keywords available]

Indexed keywords

COMPUTER CONTROL; CUTTING TOOLS; ERROR ANALYSIS; FORCE CONTROL; MILLING MACHINES; NUMERICAL CONTROL SYSTEMS; ONLINE SYSTEMS; PRODUCTIVITY; SURFACE PROPERTIES;

CUTTING FORCES; END MILLING ACCURACY; ON LINE FEED RATE CONTROLS; SURFACE ERRORS; TOOL DEFLECTION COMPENSATION;

MILLING (MACHINING);

EID: 0032074787     PISSN: 10871357     EISSN: 15288935     Source Type: Journal    
DOI: 10.1115/1.2830117     Document Type: Article

References (24)

1. Altintas, Y., 1994, “Direct Adaptive Control of End Milling Process,” Int. Mach. Tools Manufact., Vol. 34, No. 4, pp. 461-472.
2. Altintas, Y., and Yellowley, I., 1987, “The Identification of Radial Width and Axial Depth of Cut in Peripheral Milling,” Int. Mach. Tools Manufact., Vol. 27, No. 3, pp. 367-381.
3. Armarego, E. J. A., and Deshpande, N. P., 1991, “Computerized End-Milling Forces Predictions with Cutting Models Allowing for Eccentricity and Cutter Deflections,” Annals of the CIRP, Vol. 40, No. 1, pp. 25-29.
4. Ber, A., Rotberg, J., and Zombach, S., 1988, “A Method for Cutting Force Evaluation of End Mills,” Annals of the CIRP, Vol. 37, No. 1, pp. 37-40.
5. Budak, E., and Altintas, Y., 1994, “Peripheral Milling Conditions for Improved Dimensional Accuracy,” Int. Mach. Tools Manufact., Vol. 34, No. 7, pp. 907-918.
6. Elbestawi, M. A., Mohamed, Y., and Liu, L., 1990, “Application of Some Parameter Adaptive Control Algorithms in Machining,” ASME Journal of Dynamic Systems, Measurement, and Control, December, Vol. 112, pp. 611-617.
7. Kline, W. A., Devor, R. E., and Lindberg, J. R., 1982, “The Prediction of Cutting Forces in End Milling with Application to Cornering Cuts,” Int. J. Mach. Tool Des. Res., Vol. 22, No. 1, pp. 7-22.
8. Kline, W. A., Devor, R. E., and Shareef, I. A., 1982,’ ‘The Prediction of Surface Accuracy in End Milling,” ASME JOURNAL OP ENGINEERING FOR INDUSTRY, August, Vol. 104, pp. 272-278.
9. Kolarits, F. M., and DeVries, W. R., 1991, “A Mechanistic Dynamic Model of End Milling for Process Controller Simulation,” ASME JOURNAL OF ENGINEERING FOR INDUSTRY, May, Vol. 113, pp. 176-183.
10. Liang, S. Y., and Perry, S. A., 1994, “In-Process Compensation for Milling Cutter Runout via Chip Load Manipulation,” ASME JOURNAL OF ENGINEERING FOR INDUSTRY, May, Vol. 116, pp. 153-160.
11. Matsubara, T., Yamamoto, H., and Mizumoto, H., 1987, “Study on Accuracy in End Mill Operations (1st Report)—Stiffness of End Mill and Machining Accuracy in Side Cutting,” Bull. Japan Soc. Of Prec. Engg., Vol. 21, No. 2, June, pp. 95-100.
12. Matsubara, T., Yamamoto, H., and Mizumoto, H., 1987, “Study on Accuracy in End Mill Operations (2nd Report)—Stiffness of End Mill and Machining Accuracy in Side Cutting,” Bull. Japan Soc. Of Prec. Engg., Vol. 25, No. 4, Dec, pp. 291-296.
13. Milner, D. A., 1974, “Controller System Design for Feedrate Control by Deflection Sensing of a Machining Process,” Int. J. Mach. Tool Des. Res., Vol. 14, pp. 187-197.
14. Oraby, S. E., and Hayhurst, D. R., 1990, “High-Capacity Compact Three-Component Cutting Force Dynamometer,” Int. Mach. Tools Manufact., Vol. 30, No. 4, pp. 549-559.
15. Sim, C. G., and Yang, M. Y., 1993, “The Prediction of the Cutting Force in Ball-End Milling with a Flexible Cutter,” Int. Mach. Tools Manufact., Vol. 33, No. 2, pp. 267-284.
16. Smith, S., and Tlusty, J., 1991, “An Overview of Modeling and Simulation of the Milling Process,” ASME JOURNAL OF ENGINEERING FOR INDUSTRY, February, Vol. 113, pp. 169-175.
17. Sutherland, J. W., and Devor, R. E., 1986, “An Improved Method for Cutting Force and Surface Error Prediction in Flexible End Milling Systems,” ASME JOURNAL OP ENGINEERING FOR INDUSTRY, November, Vol. 108, pp. 269-279.
18. Tani, Y., Hatamura, Y., and Nagao, T., 1983, “Development of Small Threecomponent Dynamometer for Cutting Force Measurement,” Bulletin of the JSME, Vol. 26, No. 214, April, pp. 650-658.
19. Tarn, J. H., and Tomizuka, M., 1989, “On-Line Monitoring of Tool and Cutting Conditions in Milling,” ASME JOURNAL OF ENGINEERING FOR INDUSTRY, August, Vol. 111, pp. 207-212.
20. Tarng, Y. S., and Cheng, S. T., 1993, “Fuzzy Control of Feed Rate on End Milling Operations,” Int. Mach. Tools Manufact., Vol. 33, No. 4, pp. 643-650.
21. Watanabe, T., and Iwai, S., 1983, “A Control System to Improve the Accuracy of Finished Surfaces in Milling,” ASME Journal of Dynamic Systems, Measurement, and Control, September, Vol. 105, pp. 192-199.
22. Yang, M. Y., and Park, H. D., 1991, “The Prediction of Cutting Force in Ball- End Milling,” Int. Mach. Tools Manufact., Vol. 31, No. 1, pp. 45-54.
23. Yang, M. Y., and Sim, C. G., 1993, “Reduction of Machining Errors by Adjustment of Feedrates in the Ball-End Mill Process,” Int. J. Prod., Vol. 31, No. 3, pp. 665-689.
24. Yazar, Z., Koch, K. F., Merrick, T., and Altan, T., 1994, “Feed Rate Optimization Based on Cutting Force Calculations in 3-Axis Milling of Dies and Molds with Sculptured Surfaces,” Int. Mach Tools Manufact., Vol. 34, No. 3, pp. 365-377.