Influence of residual stresses and loading frequencies on corrosion fatigue crack growth behavior of weldments

Metallurgical and Materials Transactions A: Physical Metallurgy and Materials Science

Volumn 29, Issue 4, 1998, Pages 1289-1298

  Kitsunai, Y ^a   Tanaka, M ^a   Yoshihisa, E ^a  

^a NATIONAL INSTITUTE OF OCCUPATIONAL SAFETY AND HEALTH   (Japan)

Author keywords

[No Author keywords available]

Indexed keywords

CRACK PROPAGATION; FATIGUE TESTING; HYDROGEN EMBRITTLEMENT; RESIDUAL STRESSES; SEAWATER CORROSION; STRESS CONCENTRATION; STRESS INTENSITY FACTORS;

CENTER CRACKED TENSION (CCT); SINGLE EDGE CRACKED TENSION (SECT);

WELDS;

EID: 0032046239     PISSN: 10735623     EISSN: None     Source Type: Journal    
DOI: 10.1007/s11661-998-0255-2     Document Type: Article

References (31)

1. W.G. Clark, Jr. and D.S. Kim: Eng. Fract. Mech., 1972, vol. 4, pp. 499-510.
2. S.M. El-Sounani and R.M. Pelloux: Weld. Res. Suppl., 1975, May, pp. 141s-152s.
3. D.A. Davis and E.J. Czyryca: ASME J. Pressure Vessel Technol., 1981, vol. 103, pp. 314-21.
4. Y. Kitsunai: Trans. Jpn. Soc. Mech. Eng., 1981, vol. 47A, pp. 677-84 (in Japanese).
5. C.V. Nelson: ASTM STP 776, ASTM, Philadelphia, PA, 1982, pp. 172-94.
6. H. Nihei, H. Ono, and T. Tsunenari: J. Soc. Navel Architecture, 1982, No. 152, pp. 152-396 (in Japanese).
7. D.A. Davis and E.J. Czyryca: ASTM STP 801, ASTM, Philadelphia, PA, 1983, pp. 175-96.
8. Y. Kitsunai: ASTM STP 857, ASTM, Philadelphia, PA, 1985, pp. 274-92.
9. Y. Kitsunai and E. Yoshihisa: JSME Int. J., 1991, ser. I, vol. 34, pp. 339-46.
10. D.B. Dawson and R.M. Pelloux: Metall. Trans., 1974, vol. 5, pp. 723-31.
11. O. Vosikovsky: J. Eng. Mater. Technol., 1975, pp. 298-304.
12. R.P. Wei: ASTM STP 675, ASTM, Philadelphia, PA, 1979, pp. 816-40.
13. R.P. Wei and G. Shim: ASTM STP 801, ASTM, Philadelphia, PA, 1983, pp. 5-25.
14. Annual Book of ASTM Standards, ASTM, Philadelphia, PA, 1978, part 31, pp. 909-10.
15. J.C. Radon, C.M. Branco, and L.E. Culver: Int. J. Fract., 1976, vol. 12, pp. 467-69.
16. G.E. Nordmark and W.G. Fricke: J. Test. Eval., 1978, vol. 5, pp. 301-03.
17. L.K.L. Tu and B.B. Seth: J. Test. Eval., 1978, vol. 6, pp. 66-74.
18. Van der Velden, R. Ewalds, H.L. Schultze, and A. Punter: ASTM STP 801, ASTM, Philadelphia, PA, 1983, pp. 64-80.
19. K. Endo, K. Komai, and T. Shikida: ASTM STP 801, ASTM, Philadelphia, PA, 1983, pp. 81-95.
20. A.P. Parker: ASTM STP 776, ASTM, Philadelphia, PA, 1982, pp. 13-31.
21. H. Tada, P.C. Paris, and G. Irwin: The Stress Analysis of Cracks Handbook, Del Research Corp., Pennsylvania, 1985, pp. 2.33 and 2.27.
22. W. Elber: ASTM STP 486, ASTM, Philadelphia, PA, 1971, pp. 230-42.
23. H.L. Ewalds, F.C. van Doorn, and W.G. Sloof: ASTM STP 801, ASTM, Philadelphia, PA, 1983, pp. 115-34.
24. D.M. Lee and S.K. Lee: Mater. Sci. Technol., 1989, vol. 5, pp. 477-86.
25. K. Komai, M. Noguchi, and H. Okamoto: JSME Int. J., 1988, ser. I, vol. 31, pp. 613-18.
26. S. Matsuoka, H. Masuda, and M. Shimodaira: Metall. Trans. A, 1990, vol. 21 A, pp. 2189-99.
27. H. Masuda and S. Matsuoka: Corr. Sci., 1990, vol. 30, pp. 631-42.
28. K.N. Akhurst and J.T. Baker: Metall. Trans. A, 1981, vol. 12A, pp. 1059-70.
29. M. Tanaka: Metall. Mater. Trans. A, 1996, vol. 27A, pp. 2678-85.
30. A. Ohta, E. Sasaki, M. Nihei, M. Kosuge, M. Kanao, and M. Inagaki: Int. J. Fatigue, 1982, pp. 233-37.
31. ASTM Subcommittee E24.04, E-647-78T, ASTM, Philadelphia, PA, 1978.