Review on ultrasonic machining

International Journal of Machine Tools and Manufacture

Volumn 38, Issue 4, 1998, Pages 239-255

  Thoe, T B ^a   Aspinwall, D K ^a   Wise, M L H ^b  

^a UNIVERSITY OF BIRMINGHAM   (United Kingdom)

^b NONE

Author keywords

[No Author keywords available]

Indexed keywords

BRITTLENESS; CERAMIC MATERIALS; RESIDUAL STRESSES; ULTRASONIC CUTTING;

ULTRASONIC MACHINING (USM);

MACHINING;

EID: 0032042572     PISSN: 08906955     EISSN: None     Source Type: Journal    
DOI: 10.1016/S0890-6955(97)00036-9     Document Type: Article

References (109)

1. Moreland, M. A., Versatile performance of ultrasonic machining. Cer. Bull., 1988, 67(6), 1045-1047.
2. Gilmore R., Ultrasonic machining and orbital abrasion techniques, SME Technical Paper (Series) AIR, NM89-419, 1989, pp. 1-20.
3. Neppiras, E. A. and Foskett, R. D., Ultrasonic machining - II. Operating conditions and performance of ultrasonic drills. Philips Tech. Rev., 1957, 18(12), 368-379.
4. Moore D., Ultrasonic impact grinding, Proc. Non-traditional Machining Conf., Cincinnati, 1985, pp. 137-139.
5. Koval'chenko, M. S., Paustovskii, A. V. and Perevyazko, V. A., Influence of properties of abrasive materials on the effectiveness of ultrasonic machining of ceramics. Sov. Powder Metallurgy and Metal Cer., 1986, 25(7), 560-562.
6. Gilmore R., Ultrasonic machining of ceramics, SME Paper, MS90-346, 1990, 12 p.
7. Rozenberg L. D., Kazantsev V. F. et al., Ultrasonic cutting, Consultants Bureau, New York, 1964.
8. Kohls, J. B., Ultrasonic manufacturing process: Ultrasonic machining (USM) and ultrasonic impact grinding (USIG). The Carbide and Tool J., 1984, 16(5), 12-15.
9. Haslehurst M., Manufacturing technology (3rd edn.), 1981, pp. 270-271.
10. Soundararajan, V. and Radhakrishnan, V., An experimental investigation on the basic mechanisms involved in ultrasonic machining. Int. J. MTDR, 1986, 26(3), 307-321.
11. Satyanarayana, A. and Krishna Reddy, B. G., Design of velocity transformers for ultrasonic machining. Electrical India, 1984, 24(14), 11-20.
12. Drozda T. J. and Wick C., Non-traditional machining - Book chapter 29: Tool and manufacturing engineers handbook (Desk Ed.), Soc. Manuf Engrs, Dearborn, MI, ISBN No. 0872633519, 1, 1983, pp. 1-23.
13. Pentland, E. W. and Ektermanis, J. A., Improving ultrasonic machining rates - some feasibility studies. J. Engg. for Ind., Trans. of the ASME, 1965, 87(Series B), 39-46.
14. Lehman R. L., Primer on engineering ceramics, Ad. Materials and Processes, 141(6), 1992.
15. Brook R. J., Concise encyclopedia of advanced ceramic materials, Pergamon Press, 1991, pp. 1-2 and p. 488.
16. Kennedy, D. C. and Grieve, R. J., Ultrasonic machining - A review. The Prod. Engineer, 1975, 54(9), 481-486.
17. Perkins J., An outline of power ultrasonics, Technical Report by Kerry Ultrasonics, 1972, 7 p.
18. Farago, F. T., Abrasive methods engineering. Industrial Press, 1980, 2, 480-481.
19. Moreland M. A., Ultrasonic impact grinding: What it is: What it will do, 1984 Proc. - 22nd Abrasive Engg. Soc. Conf.: Abrasives and Hi-Technology, A 2-way Street, 1984, pp. 111-117.
20. Seah, K. H. W., Wong, Y. S. and Lee, L. C., Design of tool holders for ultrasonic machining using FEM. J. Materials Processing Technology, 1993, 37(1-4), 801-816.
21. Markov, A. I., Kinematics of the dimensional ultrasonic machining method. Machines and Tooling, 1959, 30(10), 28-31.
22. Kainth, G. S., Nandy, Amitav and Singh, Kuldeep, On the mechanics of material removal in ultrasonic machining. Int. J. MTDR, Pergamon Press, 1979, 19, 33-41.
23. Kremer, D., The state of the art of ultrasonic machining. Annals of the CIRP, 1981, 30(1), 107-110.
24. Gilmore, R., Ultrasonic machining: A case study. 7 Int Conf on Computer-Aided Prod. Engg., 1991, 28(1-2), 139-148.
25. Moreland M. A., Ultrasonic machining - Book chapter: Ceramics and glasses, ASM International, Engineering Material Handbook, 4, pp. 359-362, ISBN 0871702827, Schneider and Samuel J. (1991).
26. Nishimura, G., Ultrasonic machining - Part I. J. Fac. Engg. Tokyo Univ., 1954, 24(3), 65-100.
27. Neppiras E. A., Report on ultrasonic machining, Metalworking Prod., 100, pp. 1283-1288, 1333-1336, 1377-1382, 1420-1424, 1464-1468, 1554-1560, 1599-1604 (1956).
28. Weller, E. J., Non-traditional machining processes (2nd edn.), Soc. of Manuf. Engineers, 1984, pp. 15-71.
29. Farrer, J. O., English Patent No. 602801 from 3.6.1948 - USM.
30. Scab, K. H. W. et al., Parametric studies of ultrasonic machining, SME Tech. paper, MR90-294, 1990, 11 p.
31. Neppiras, E. A., Macrosonics in industry: 1. Introduction. Ultrasonics, 1972, 10, 9-13.
32. Balamuth, L., Ultrasonic vibrations assist cutting tools. Metalworking Prod., 1964, 108(24), 75-77.
33. Kremer, D., New developments on ultrasonic machining, SME Technical Paper, MR91-522, 1991, 13 p.
34. Clifton, D., Imal, Y. and McGeough, J. A., Some ultrasonic effects on machining materials encountered in the offshore industries, Proc. 30th Int. MATADOR Conf., 1993, pp. 119-123.
35. Shaw, M. C., Ultrasonic grinding. Microtechnic, 1956, 10(6), 257-265.
36. Neppiras, E. A., Ultrasonic machining and forming. Ultrasonics, 1964, 2, 167-173.
37. Machining data handbook (3rd edn.), Compiled by the Technical Staff of the Machinability Data Centre, Cincinnati Metcut Research Associates Inc., 1980, 2, 43-63.
38. Venkatesh, V. C., Machining of glass by impact processes. J. Mech. Working Technology, 1983, 8, 247-260.
39. Hartley, M. S., Ultrasonic machining of brittle materials. Electronics, 1956, 29(1), 132-135.
40. McGeough, J. A., Advanced methods of machining, Chapman and Hall, ISBN 0412319705, 1988, pp. 170-198.
41. Komaraiah, M., Manan, M. A., Narasimha Reddy, P. and Victor, S., Investigation of surface roughness and accuracy in ultrasonic machining. Precision Engg., 1988, 10(2), 59-65.
42. Balamuth, L. A., Ultrasonic assistance to conventional metal removal. Ultrasonics, 1966, 4, 125-130.
43. Graff, K. F., Macrosonics in industry: 5. ultrasonic machining. Ultrasonics, 1975, 13, 103-109.
44. Ultrasonics - can aid conventional machining, Metalworking Prod., 1962, 106(38), 55-56.
45. Isaev, A. I., Learning with ultrasonically vibrated reamers. Machines and Tooling, 1962, 33(6), 27-30.
46. Moreland, M. A., Ultrasonic advantages revealed in the hole story. Cer. Appl. Manuf., 1988, 187, 156-162.
47. Murti, V. S. R. and Philip, P. K., A comparative evaluation of ultrasonic assisted EDM through topographical indices, 12th AIMTDR Conf., IIT Delhi, Tata McGraw Hill, New Delhi, 1986, pp. 365-369.
48. Halm, R. and Schulz, P., Ultrasonic machining of complex ceramic components, Erosion AG Report, DKG 70. No. 7, 1993, 6p.
49. Black, P., An ultrasonic impact grinding technique for electrode-forming and redressing, Proc. Non-traditional Machining Conf., Cincinnati, Ohio, ASM, 1985, pp. 129-136.
50. Kremer, D., Bazine, G. and Moison, A., Ultrasonic machining improves EDM. technology, Electromachining, Proc. 7th Int. Symp., ed. by Prof. Crookall J. R., Birmingham, UK, 1983, pp. 67-76.
51. Ghabrial, S. R., Trends towards improving surfaces produced by modem processes, Wear, 109, No. 1-4, Paper presented at the 3rd Int. Conf. on Metrol and Prop. of Eng'g Surf, Teesside, Engl., 1986, pp. 113-118.
52. Ghabrial, S. R., Trends towards improving surfaces produced by modem processes, Wear, 109, No. 1-4, Paper presented at the 3rd Int. Conf. on Metrol and Prop. of Eng'g Surf, Teesside, Engl., 1986, pp. 113-118.
53. Thoe, T. B., Ultrasonic contour machining of ceramic materials, MPhil Thesis, Uni. of Birmingham (1994).
54. Gilmore, R., Ultrasonic machining, SME Technical Paper, EM89-123, 1989, 10p.
55. Essam, G. R., The application of rotary ultrasonic machining to ceramic turbine blades, Rolls Royce Lab'y Rep., LLR 30898 (1984).
56. Iwanek, H., Grathwohl, G., Hamminger, R. and Brugger, N., Machining of ceramics by different methods, Cer. Mat'ls and Components for Engines, Proc. 2nd Int. Symp., 1986, pp. 417-423.
57. Oh, H. L., Pankow, D. and Finnie, I., The mechanism of ultrasonic machining of brittle solids, Proc. Int. Conf. Prod. Eng., Tokyo, Part II, 1974, pp. 109-113.
58. Jay, F., IEEE standard dictionary of electrical and electronics terms, 3rd edition, 1984, pp. 405 and 519.
59. Lucas, M., ESPI Analysis of Ultrasonic Machining Sonotrodes - A consultancy report to T and N, Loughborough Consultants Limited (1992).
60. Boothroyd, G. and Knight, W. A., Fundamentals of machining and machine tools (2nd Edition), Marcel Dekker, 1989, pp. 469-475; 490-499 and 510-515.
61. Neppiras, E. A. and Foskett, R. D., Ultrasonic machining - I. Technique and equipment. Philips Tech. Rev., 1957, 18(11), 325-334.
62. Legge, P., Machining without abrasive slurry. Ultrasonics, 1966, 4, 157-162.
63. Ed. by L. D. Rozenberg, Physical principles of ultrasonic technology - Vol. 1 and 2, Plenum Press, N. Y. (1973).
64. Frederick, J. R., Ultrasonic engineering, John Wiley and Sons Inc., New York, ISBN 0471277258 (1965).
65. Kaczmarek, I., Impact Grinding (Ultrasonic machining) - Book chapter 21: Principles of machining by cutting, abrasion and erosion, Peter Peregrinus Ltd., Stevenage, ISBN 0901223662, 1976, pp. 448-462.
66. Rawson, F. F., High power ultrasonic resonant horns, part 1 - Basic design concepts, velocity of ultrasound at 20 KHz; effects of material and horn dimensions, Ultrasonics Int. 87 Conf. Proc., London, 1987, pp. 680-685.
67. Prabhakar, D. and Haselkorn, M., An experimental investigation of material removal rates in rotary ultrasonic machining. Trans. of NAMRI/SME, 1992, 20, 211-218.
68. Amin, S. G., Ahmed, M. H. M. and Youssef, H. A., Optimum design charts of acoustic horns for ultrasonic machining. Proc. Int. Conf on AMPT'93, 1993, 1, 139-147.
69. Thoe, T. B., Aspinwall, D. K. and Wise, M. L. H., The effect of operating parameters when ultrasonic contour machining, Twelfth Annual Conference of the Irish Manufacturing Committee (IMC-12), Cork, Ireland, September 1995, pp. 305-312.
70. US400 - Ultrasonic machining system, Brochure from Erosonic AG (1994).
71. Wojchiechowski, M. P. et al., Ultrasonic machining: Past, present and future, SME Paper, MR72-188, 1972, 12p.
72. Adithan, M., Tool wear studies in ultrasonic drilling. Wear, 1974, 29, 81-93.
73. Kumehara, H., Characteristics of threaded joints in ultrasonic vibrating system. Bull. of JSME, 1984, 27(223), 117-123.
74. Adithan, M., Production accuracy of holes in ultrasonic drilling. Wear, 1976, 40(3), 309-318.
75. Kazantsev, V. F., Improving the output and accuracy of ultrasonic machining. Machines and Tooling, 1966, 37(4), 33-39.
76. Ultrasonic machining of glass at the N. P.L., Machinery, May 1964, pp. 1172-1176.
77. Adithan, M., Abrasive wear in ultrasonic drilling. Tribology International, 1983, 16(5), 253-255.
78. Goetze, D., Effect of vibration amplitude, frequency and composition of the abrasive slurry on the rate of ultrasonic machining in Ketos tool steel. The J. Acoust. Soc. of Am., 1956, 28(6), 1033-1037.
79. Krar S. F. and Ratterman E., Superabrasives - Grinding and machining, McGraw Hill, 1990, pp. 12.
80. Miller, G. E., Special theory of ultrasonic machining. J. Appl. Phy., 1957, 28(2), 149-156.
81. Cook N. H., Manufacturing analysis, Addison-Wesley, New York, 1966, pp. 133-138.
82. Khairy, A. B. E., Assessment of some dynamic parameters for the ultrasonic machining process. Wear, 1990, 137, 187-198.
83. Ghabriel, S. R., Saleh, S. M., Kohail, A. and Moisan, A., Problems associated with electrodischarge machined electrechemically machined and ultrasonically machined surfaces. Wear, 1982, 83, 275-283.
84. Komaraiah, M and Narasimha Reddy, P, A study on the influence of workpiece properties in ultrasonic machining. Int. J. Mach. Tools Manuf, 1993, 33(3), 495-505.
85. Enomoto, Y., Sliding fracture of soda-lime glass in liquid environments. J. Mat'l Science, 1981, 16(12), 3365-3370.
86. Lucas M. and Chapman G. M., Vibration analysis at ultrasonic frequencies, The 1989 ASME Ds. Tech'l Conf.-12th Biennial Conf on Mech'l Vib. and Noise,Montreal, DE-Vol. 18-4, September 1989, pp. 235-240.
87. Smith, T. J., Parameter influence in ultrasonic machining. Ultrasonics, 1973, 11(5), 196-198.
88. Markov A. I., Ultrasonic machining of intractable materials Iliffe Books Ltd., London (1966).
89. Adithan, M. and Venkatesh, V. C., Study of the performance characteristics of an ultrasonic drilling head. Wear, 1975, 33, 261-270.
90. Kubota, M., Tamura, Y. and Shimamura, N., Ultrasonic machining with a diamond impregnated tool. Bull. Japan. Soc. of Prec. Engg., 1977, 11(3), 127-132.
91. Komaraiah, M. and Reddy, P., Narashima, Rotary ultrasonic machining - A new cutting process and its performance. Int. J. Prod. Res., 1991, 29(11), 2177-2187.
92. Takeyama, H., Burrless drilling by means of ultrasonic vibration. Annals of CIRP, 1991, 40(1), 83-86.
93. Kops, L., Investigation into the influence of the wear of the abrasive powder on the technological indices of ultrasonic machining. CIRP Annalen, Springer Verlag, Berlin, 1964, 12(3), 151-157.
94. Kazantsev, V. F., The relationship between output and machining conditions in ultrasonic machining. Machines and Tooling, 1963, 34, 14-17.
95. Smith, T. L., Parameter influence in ultrasonic machining, BSc(Hon) Diss., The Nottingham Trent Uni., (1971),
96. Ghabrial, S. R., Saleh, S. M., Moisan, A. and Kremer D., Some aids towards improving performance in U. S.M. 1984 SME Manuf Engg. Trans., 12th NAMRC Conf. Proc., 1984, pp. 227-232.
97. Markov, A. I., Ultrasonic drilling and milling of hard non-metallic materials with diamond tools. Machines and Tooling, 1977, 48(9), 45-47.
98. Komaraiah, M. and Reddy, P. N., Relative performance of tool materials in ultrasonic machining. Wear, 1993, 161(1-2), 1-10.
99. Adithan, M., Tool wear characteristics in ultrasonic drilling. Tribology Int., 1981, 14(6), 351-356.
100. Adithan, M. and Venkatesh, V. C., Parameter influence on tool wear in ultrasonic drilling. Tribology Int., 1974, 7(6), 260-264.
101. Riddei, V., Cavitation erosion - A survey of the literature, 1940-1970. Wear, 1973, 23, 133-136.
102. Nandi, G., Mukherjee, S. K. et al., Tool wear in ultrasonic trepanning of glass-ceramics, The Japan soc. of Precision Engg., Proc. 5th Int. Conf on Prod. Engg. Tokyo 1984, 1984, pp. 283-287.
103. Clouser, H. A., New techniques for electrode forming, Res. and Technological Dev. in Non-traditional Machining Presented at the Winter Annual Meeting of the ASME, 1988, pp. 75-88.
104. Dam, H. et.al., Surface characterization of ultrasonic machined ceramics with diamond impregnated sonotrode, Proc. the Int. Conf. on Machining of Adv. Mat'ls, Gaithersburg, Maryland, July 1993, pp. 125-133.
105. Ultrasonic assembly of thermoplastic mouldings and semi-finished product - Recommendations on methods, construction and applications. Manual written by German Electrical Manufacturers Association ZVEI.
106. Merkulov, L. G., Design of ultrasonic concentrations. Akusticheskiy Zhurnal, 1957, 3, 246-255.
107. Pandey, P. C. and Shan, H. S., Modern machining processes, Tata McGraw-Hill, Chapter 2, 1980, pp. 7-38.
108. Amin, S. G., Ahmed, M. H. M. and Youssef, H. A., Computer aided design of acoustic horns for ultrasonic machining using finite element analysis. Proc. AMPT93 Conf., 1993, 2, 1455-1465.
109. Hahn, R., Ultrasonic machining of glass and ceramics. Am. Cer. Soc. Bull., 1993, 72(8), 103-106.