A contribution to the stability of stiffened plates under uniform compression

Computers and Structures

Volumn 66, Issue 5, 1998, Pages 535-570

  Bedair, Osama K ^a  

^a NATIONAL RESEARCH COUNCIL CANADA   (Canada)

Author keywords

Analysis of stiffened plates; Design and optimization of stiffened plates; Mathematical programming; Plate buckling; Stability; Stiffened plates; Ultimate strength of stiffened plates

Indexed keywords

BUCKLING LOAD; MINIMUM WEIGHT DESIGN; ORTHOTROPIC PLATE EQUATION; STIFFENED PLATES;

BEAMS AND GIRDERS; BOUNDARY CONDITIONS; BUCKLING; COMPRESSIVE STRENGTH; DIFFERENTIAL EQUATIONS; FINITE ELEMENT METHOD; OPTIMIZATION; QUADRATIC PROGRAMMING; STABILITY; STIFFNESS; STRAIN;

PLATES (STRUCTURAL COMPONENTS);

EID: 0032021251     PISSN: 00457949     EISSN: None     Source Type: Journal    
DOI: 10.1016/s0045-7949(97)00102-8     Document Type: Article

References (143)

1. Guyon, Y. Calcul des ponts larges a poutres multiples solidarisees par des entretoises. Annuelles des Pont et Chaussees de France, 1946, 10(9), 553-612.
2. Massonnet, C. Methode de calcul des ponts a poutres multiples tenant compte de leur resistance a la torsion. Pub. Int. ABSE, 1950, 10, 680-748.
3. Cox, H. L. Computation of initial buckling stress of sheet stiffener combinations. Journal of the Royal Aeronautical Society, 1954, 58, 634-638.
4. Martin, D. W. and Cox, H. L. The buckling modes of longitudinally stiffened flat panel. Aeronautical Quarterly, 1963, 14, 346-398.
5. Klitchieff, J. M. and Belgrade, Y. On the stability of plates reinforced by ribs. Journal of Applied Mechanics, 1949, 16, 74-76.
6. Hovichitr, I., Karasudhi, P., Nishino, F. and Lee, S. L. A rational analysis of plates with eccentric stiffeners. IABSE Proceedings, 1977, P4/77, 1-14.
7. Hoppman, H. W., Huffington, N. J. and Magness, L. S. A study of orthogonally stiffened plates. Journal of Applied Mechanics, Transactions of the ASME, 1956, 23, 243-250.
8. Hoppmann, W. H. and Baltimore, M. Bending of orthogonally stiffened plates. Journal of Applied Mechanics, 1955, 22, 267-271.
9. Soper, W. Large deflection of stiffened plates. Journal of Applied Mechanics, 1958, 25, 444-448.
10. Maaskant, R., Interactive buckling of biaxially loaded elastic plate structures. Ph.D. Dissertation, University of Waterloo, 1989.
11. Kagan, H. A. and Kubo, G. G. Elasto-plastic analysis of reinforced plates. ASCEST4, 1968, 94, 943-958.
12. Allman, D. J. Calculation of the elastic buckling loads of thin flat plates using triangular finite element. International Journal for Numerical Methods in Engineering, 1975, 9, 415-432.
13. Hagedoorn, H. J., An elastic finite element analysis of the buckling of eccentrically stiffened plates and shells. Ph.D. Dissertation, Cornell University, 1973.
14. Crisfield, M. A., Large deflection elasto-plastic buckling analysis of plates using finite elements. TRRL, Report no. 593, 1973.
15. Crisfield, M. A., Large deflection elasto-plastic buckling analysis of eccentrically stiffened plates using finite elements. TRRL Laboratory, Report no. 725, 1976.
16. Crisfield, M. A. Full range analysis of steel plates and stiffened plating under uniaxial compression. Proceedings of the Institution of Civil Engineers, 1975, II, 595-624.
17. Crisfield M. and Puthli, R., A finite element method applied to the collapse analysis of stiffened box girder diaphragms. In Steel Plated Structures. Crosby Lockwood Staples, London, 1976, pp. 311-337.
18. Wegmuller, A. W. Full range analysis of eccentrically stiffened plates. ASCE, 1974, 100(ST1), 143-159.
19. Wegmuller A. W. and Costem, C. N., Finite Element Analysis Of Plates and Eccentrically Stiffened Plates. Fritz Engineering Laboratory, Lehigh University, 1973.
20. Przemieniecki, J. S. Finite element structural analysis of local instability. AIAA Journal, 1973, 11, 33-39.
21. Przemieniecki, J. Discrete-element methods for stability analysis of complex structures. The Aeronautical Journal of The Royal Aeronautical Society, 1968, 72, 1077-1086.
22. Rahal, K. N. Transversely stiffened girder webs subjected to combined in-plane loading. Proceedings of the Institution of Civil Engineers, Part II, 1991, 91, 237-258.
23. Rahal, K. N. and Harding, J. E. Transversely stiffened girder webs subjected to shear loading, Part I - behavior. Proceedings of the Institution of Civil Engineers, Part II, 1990, 89, 47-65.
24. Rahal, K. and Harding, J. Transversely stiffened girder webs subjected to shear loading, Part II -Stiffener design. Proceedings of the Institution of Civil Engineers, Part II, 1990, 89, 67-87.
25. Fafard, M., Beaulieu, D. and Dhatt, G. Buckling of thin walled members by finite element method. Computers and Structures, 1987, 25, 183-190.
26. Komatsu, S., Nara, S. and Kitada, T. Elasto-plastic analysis of orthogonally stiffened plates with initial imperfections under uniaxial compression. Computers and Structures, 1980, 11, 429-437.
27. Valsgard, S. Numerical design prediction of the capacity of plates in biaxial in-plane compression. Computers and Structures, 1980, 11, 429-437.
28. Shastry, B., Venkateswara and Reddy, M. N. Stability of stiffened plates using high precision finite elements. Nuclear Engineering and Design, 1976, 36, 91-95.
29. Soreide, T., Moan, T. and Nordsve, N. On the behaviour and design of stiffened plates in the ultimate limit stat. International Journal of Ship Building Progress, 1978, 22, 238-244.
30. Soreide, T. H., Bergan, P. G. and Moan, T., Ultimate collapse behaviour of stiffened plates using alternate F.E. formulations. In Steel Plated Structures. Crosby Lockwood Staples, London, 1976, pp. 618-632.
31. Koko, T. S. and Olson, M. D. Non-linear analysis of stiffened plates using super element. International Journal for Numerical Methods in Engineering, 1991, 31, 319-343.
32. Turvey, G. A contribution to the elastic stability of thin walled structures fabricated from isotropic and orthotropic materials. Ph.D. Dissertation, University of Birmingham, 1971.
33. Turvey, G. J. and Wittrick, W. H. The influence of orthotropy on the stability of some multi-plate structures in compression. Aeronautical Quarterly, 1973, 24, 1-8.
34. Yoshida, H. and Maegawa, K. Buckling strength of orthogonally stiffened plates. Journal of Structural Mechanics, 1979, 7, 161-191.
35. Cheung Y. K. and Delcourt, C., Buckling and vibration of thin flat-walled structures continuous over several spans. Proceedings of the Institution of Civil Engineers, Part II, 1977, 93-103.
36. Graves Smith, T. R. and Sridharan, S. A finite strip method for the post-locally-buckled analysis of plate structures. International Journal of Mechanical Sciences, 1978, 20, 685-693.
37. Hancock, G. J., Non-linear analysis of thin walled I - section in bending. In Aspects of the Analysis of Plate Structures. Clarendon Press, Oxford, 1985, pp. 251-267.
38. Hancock, G. J., Davids, A., Key, P. W., Laue, S. C. W. and Rasmussen, J. R. Recent developments in buckling of non-linear analysis of thin walled structural members. Thin Walled Structures, 1990, 9, 309-338.
39. Bradford, M. A. and Hancock, G. J. Elastic interaction of local and lateral buckling in beams. Thin Walled Structures, 1984, 2, 1-25.
40. Murray, N. W. and Theirauf, G., Tables For the Design and Analysis of Stiffened Steel Plates. Birkhauser Verlag, 1983.
41. Lavy, Y., Yoseph, B. and Rosenhouse, G. Mixed-hybrid finite strip method for folded plate structures. Computers and Structures, 1992, 42, 433-446.
42. Kakol, W. Stability analysis of stiffened plates by finite strip. Thin Walled Structures, 1990, 10, 277-297.
43. Mahendran, M. and Murray, N. W. Elastic buckling analysis of ideal thin-walled structures under combined loading using a finite strip method. Thin Walled Structures, 1986, 4, 329-362.
44. Wittrick, W. H. General sinusoidal stiffness matrices for buckling and vibration analysis of thin flat-walled structures. International Journal of Mechanical Sciences, 1968, 10, 949-966.
45. Wittrick, W. H. A unified approach to the initial buckling of stiffened panels in compression. Aeronautical Quarterly, 1968, 19, 265-283.
46. Wittrick, W. H. and Curzon, P. L. Nodal lines for long plates in combined shear and compression with sinusoidal edge rotation. Aeronautical Quarterly, 1969, 20, 1-16.
47. Wittrick, W. H. and Curzon, P. L. Buckling of a long flat panel with a series of equidistant longitudinal supports in combined longitudinal compression and shear. Aeronautical Quarterly, 1969, 20, 17-24.
48. Djahni, P., Large-deflection elasto-plastic analysis of discretely stiffened plates. Ph.D Dissertation, Imperial College of Science and Technology, 1974.
49. Webb, S. E., Stiffened plating under combined in-plane and lateral loading. Ph.D Dissertation, Imperial College of Science and Technology, 1980.
50. Webb, S. E. and Dowling, P. J. Large deflection elasto-plastic behaviour of discretely stiffened plates. Proceedings of the Institution of Civil Engrs, Part II, 1975, 59, 501-514.
51. Dean, D. and Omid'varan, C. Analysis of ribbed plates. ASCE, 1969, 95, 411-442.
52. Dean, D. L. and Abdel-Malek, R. A. Rational analysis of orthotropic bridge decks. International Journal of Mechanical Sciences, 1974, 16, 173-192.
53. Dean, D. L. and Avent, R. R. Analysis of metal plate-stringer bridge decks. IABSE, 1975, 35, 45-64.
54. Dean, D. L. and Gangarao, A. M. R. R. Macro approach to discrete field analysis. ASCE Journal of Structural Engineering, 1971, 96, 377-394.
55. Bounin, K., Discrete field stability analysis of ribbed plates. Ph.D. Dissertation, Georgia Institute of Technology, 1975.
56. Avent, R. and Bounin, D. Discrete field stability analysis of ribbed plates. ASCE, Journal of Structural Engineering, 1976, 102(ST9), 1917-1937.
57. Beedle, L. S., ed., Stability of Metal Structures, a World View, 2nd edn. Structural Stability Research Council, USA, 1991.
58. Galambos, T. V., Guide to Stability Design Criteria for Metal Structures, 4th edn. Structural Stability Research Council, John Wiley and Sons, New York, 1988.
59. Gaylord, E. H. and Gaylord, C. N., eds., Structural Engineering Handbook. McGraw-Hill, New York, 1990.
60. Column Research Committee of Japan, Handbook of Structural Stability. Corona, Tokyo, 1971.
61. Coan, J. M. Large deflection theory for plates with small initial curvature loaded in compression. Journal of Applied Mechanics, 1951, 18, 143-151.
62. Dawson, R. G. and Walker, A. C. Post buckling of geometrically imperfect panels. ASCE, Journal of the Structural Division, 1972, 98, 75-94.
63. Levy, S. and Krupen, P., Large deflection theory for end compression of long rectangular plates rigidly clamped along two edges. NACA TN 884, 1943.
64. Rhodes, J. and Harvey, J. M. Plates in uniaxial compression with various support conditions at unloaded boundaries. International Journal of Mechanical Sciences, 1971, 13, 787-802.
65. Rhodes, J. and Harvey, J. M. Examination of plate post-buckling behaviour. ASCE Journal of Engineering Mechanics, 1977, 103, 461-479.
66. Rushton, K. R., Post-buckling of rectangular plates with various boundary conditions. Aeronautical Quarterly, 1970, 163-181.
67. Timoshenko, S. P. and Gere, J. M., Theory of Elastic Stability. McGraw-Hill, New York, 1961.
68. Walker, A. C. The post-buckling behaviour of simply supported square plates. Aeronautical Quarterly, 1969, 20, 203-222.
69. Williams, D. G. and Walker, A. C. Explicit solutions for the design of initially deformed plates subject to compression. Proceedings of the Institution of Civil Engineers, Part II, 1975, 59, 763-787.
70. Williams, D. G. and Walker, A. C. Explicit solutions for the plate buckling analysis. ASCE Journal of Engineering Mechanics, 1977, 103, 549-568.
71. Yamaki, N. Post-buckling behaviour of rectangular plates with small initial curvatures loaded in edge compression. Journal of Applied Mechanics, 1960, 27, 407-414.
72. Yamaki, N. Post-buckling behaviour of rectangular plates with small initial curvatures loaded in edge compression, continued. Journal of Applied Mechanics, 1960, 27, 335-342.
73. Rhodes, J. and Harvey, J. M. Examination of plate post-buckling behaviour. ASCE, Journal of Engineering Mechanics, 1977, 103, 461-478.
74. Bedair, O. K. and Sherbourne, A. N. Plate/stiffener assemblies in uniform compression: Part I - buckling. ASCE, Journal of Engineering Mechanics, 1993, 119, 1937-1955.
75. Sherbourne, A. N. and Bedair, O. K. Plate/stiffener assemblies in uniform compression: Part II - post-buckling. ASCE, Journal of of Engineering Mechanics, 1993, 119, 1956-1972.
76. Bedair O. K. and Sherbourne, A. N., Toward rational predictions of the local stability of plate/ stiffener assemblies. Proceedings of 11th Canadian Society for Civil Engineers Conference, Vol. 4, 1993, pp. 139-148.
77. Bedair, O. K. and Sherbourne, A. Plate/stiffener assemblies under non-uniform edge stress. ASCE Journal of Structural Division, 1995, 121(11), 1603-1612.
78. Bedair, O. K. and Sherbourne, A. N. The elastic stability of partially restrained plates under compression and in-plane bending. Journal of Constructional Steel Research, 1995, 35(3), 339-360.
79. Sherbourne, A. N. and Bedair, O. K., Stability of stiffened plates under combined compression and in-plane bending. Proceedings of 11th Canadian Society for Civil Engineers Conference, Vol. 4, 1993, pp. 129-138.
80. Bedair, O. K. and Sherbourne, A. N. On the stability of plates under combined compression and in-plane bending. Computers and Structures, 1995, 53, 1453-1464.
81. Bedair, O. K. and Sherbourne, A. N. Unified approach to the local stability of plate/stiffener assemblies. ASCE, Journal of Engineering Mechanics, 1995, 121(2), 214-229.
82. Horne, M. R. and Narayanan, R. An approximate method for the design of stiffened steel compression panels. Proceedings of the Institution of Civil Engineers Part II, 1975, 59, 501-514.
83. Horne, M. R. and Narayanan, R. Strength of axially loaded stiffened panels. IABSE, 1976, 36, 125-157.
84. Horne, M. R. and Narayanan, R., Ultimate strength of stiffened panels under uniaxial compression. In Steel Plated Structures ed. P. J. Dowling. Crosby Lockwood Staples, London, 1976, pp. 24-50.
85. Horne, M. R. and Narayanan, R. Design of axially loaded stiffened plates. ASCE, Journal of the Structural Division, 1977, 103(11), 2243-2257.
86. Horne, M. R. and Narayanan, R. The strength of straitened welded steel stiffened plates. The Structural Engineer, 1976, 54, 437-443.
87. Dwight, J. B. and Little, G. H. Stiffened steel compression flanges - a simpler approach. The Structural Engineer, 1976, 54, 501-505.
88. Little, G. H. Stiffened steel compression panels -theoretical failure analysis. The Structural Engineer, 1976, 54, 489-501.
89. Murray, N. W. Analysis and design of stiffened plates for collapse load. The Structural Engineer, 1975, 53, 153-158.
90. Murray, N. W. Buckling of stiffened panels loaded axially in bending. The Structural Engineer, 1973, 51, 285-301.
91. Murray, N. The behaviour of thin stiffened steel plates. IABSE, 1973, 33, 191-201.
92. Murray, N. W., ultimate capacity of stiffened plates in compression. In Plated Structures, Stability and Strength, ed. R. Narayanan. Applied Science, Amsterdam, 1983, pp. 135-163.
93. Murray, N. W. Some basic plastic mechanisms in thin walled structures. International Journal of Mechanical Sciences, 1981, 23, 703-713.
94. Dowling, P. J. Strength of steel box girders. ASCE, Journal of the Structural Division, 1975, 101(9), 1929-1945.
95. Dowling, P. J., Moolani F. M. and Frieze, P. A., The effect of shear lag on the ultimate strength of box girders. In Steel Plated Structures, ed. P. J. Dowling. Crosby Lockwood Staples, London, 1976, pp. 108-141.
96. Dowling, P., Harding, J. and Agelidis, N., Collapse of box girder stiffened webs. In Instability and Plastic Collapse of Steel Structures, 1983, pp. 380-389.
97. Dowling, P. J., Chatterjee, S., Frieze P. A. and Moolani, F. M., Experimental and predicted collapse behaviour of rectangular and trapezoidal stiffened steel box girders. In Steel Box Girder Bridges, Proceedings of the Institution of Civil Engineers, 1973, pp. 77-94.
98. Dowling, P. J., Loe, J. A. and Dean, J. A., The behaviour up to collapse of load bearing diaphragms in rectangular and trapezoidal stiffened steel box girders. In Steel Box Girder Bridges, Proceedings of the Institution of Civil Engineers, 1973, pp. 95-117.
99. Burgan, B. A., Special problems in wide and narrow stiffened compression flanges. Ph.D Dissertation, Imperial College of Science and Technology, 1987.
100. Burgan, B. A. and Dowling, P. J. The treatment of shear lag in design. Thin Walled Structures, 1990, 9, 163-174.
101. Moolani, F. M., Stiffened plating under combined in-plane and lateral loading. Ph.D Dissertation, Imperial College of Science and Technology, 1980.
102. Moolani, F. M. and Dowling, P. J., Ultimate load behaviour of stiffened plates in compression. In Steel Plated Structures, ed. P. J. Dowling. Crosby Lockwood Staples, London, 1976, pp. 51-88.
103. Chatterjee, S., Ultimate load analysis and design of stiffened plates in compression. Ph.D Dissertation, Imperial College of Science and Technology, 1978.
104. Lamas, A. R. and Dowling, P. J., Effect of shear lag on the inelastic buckling behaviour of thin-walled structures. In Thin-Walled Structures, ed. J. Rhodes and A. C. Walker, 1980, pp. 61-66.
105. Moffat, K. R. and Dowling, P. J. Shear lag in box girders. The Structural Engineer, 1975, 53, 439-448.
106. Frieze, P. A. Elasto-plastic buckling in thin-walled beams and columns. Proceedings of the Institution of Civil Engineers, 1978, 65(II), 857-874.
107. Frieze, P. A. and Dowling, P. J. Interactive buckling analysis of box sections using dynamic relaxation. Computers and Structures, 1978, 9, 431-439.
108. Frieze, P. A., Hobbs, R. E. and Dowling, P. J. Application of dynamic relaxation to the large deflection elasto-plastic analysis of plates. Computers and Structures, 1978, 8, 301-310.
109. Sherbourne, A. N., Liaw, C. Y. and Marsh, C. Stiffened plates in uniaxial compression. IABSE, 1971, 31, 145-177.
110. Massonnet, C. and Maquoi, R., New theory and tests on the ultimate strength of stiffened box girders. In Steel Box Girder Bridges, Proceedings of the Institution Civil of Engineers, 1973, pp. 131-144.
111. Jetteur, P. A new design method for stiffened compression flanges of box girders. Thin Walled Structures, 1983, 1, 189-210.
112. Murray, N. W. and Katzer, W., The collapse behaviour of stiffened steel plates which have high aspect ratios under axial compression. In Instability and Plastic Collapse Of Steel Structures, ed. L. J. Morris, 1983, pp. 432-445.
113. Fukumoto, Y., Usami, T. and Yamaguchi, K. Inelastic buckling strength of stiffened plates in compression. IABSE Proceedings, 1977, P.8/77, 1-15.
114. Yoshida, H. and Maegawa, K. Buckling strength of orthogonally stiffened plates. Journal of Structural Mechanics, 1979, 7, 161-191.
115. Schmit, L. A., Goble, G., Fox, R. L., Lasdon, L., Moses F. and Razani, R., Structural Synthesis. Case Institute of Technology, Summer Notes, 1, Ohio, 1965.
116. Schmit, L. A. and Kicher, T. P., Structural synthesis of symmetric waffle plate. NASA TN 3443, 1962.
117. Pantaik, S. N. and Srivastava, N. K. Safety of optimally designed structures like cylinders and plates. Computers and Structures, 1980, 11, 363-367.
118. Pantaik, S. N. Synthesis of waffle plates in the post buckling domain. Computational Methods in Applied Mechanics and Engineering, 1974, 4, 47-68.
119. Pantaik, S. N. and Sankaran, G. V. Optimum design of stiffened cylindrical panels with constraint on the frequency in the presence of initial stress. International Journal for Numerical Methods in Engineering, 1976, 10, 283-299.
120. Hofmeister, L. D. and Felton, L. P. Synthesis of waffle plates with multiple rib sizes. AIAA Journal, 1969, 7, 2193-2199.
121. Hofmeister, L. D. and Felton, L. P. Waffle plates with multiple rib sizes, I. Stability analysis. Journal of Spacecraft, 1970, 7, 1322-1327.
122. Hofmeister, L. D. and Felton, L. P. Waffle plates with multiple rib sizes, I. Design examples. Journal of Spacecraft, 1970, 7, 1322-1331.
123. Burns, A. B. and Skogh, J. Combined loads minimum weight analysis of stiffened plates and shells. Journal of Spacecraft and Rockets, 1966, 3, 235-240.
124. Burns, A. B. and Almroth, B. O. Structural optimization of axially compressed cylinders, considering ring-stringer eccentricity effects. Journal of Spacecraft and Rockets, 1966, 3, 1263-1268.
125. Stroud, W. J. and Agranoff, N., Minimum-mass design of filamentary composite panels under combined loads: design procedure based on simplified buckling equations. NASA TN D 8257, 1976.
126. Stroud, W. J., Agranoff, N. and Anderson, M. S., Minimum-mass design of filamentary composite panels under combined loads: design based on a rigorous buckling analysis. NASA TN D 8417, 1977.
127. Stroud, W. J. and Anderson, M. S., PASCO: structural panel analysis and sizing code capability and analytical foundations. NASA TM 80181, 1980.
128. Bushnell, D., Computerized Buckling Analysis of Shells. Martinus Nijhoff, 1985.
129. Bushnell, D. PANDA-interactive program for minimum weight design of stiffened cylindrical panels and shells. Computers and Structures, 1983, 16, 167-185.
130. Bushnell, D. Theoretical basis of the PANDA computer program for preliminarily design of stiffened panels under in-plane loads. Computers and Structures, 1987, 27, 541-563.
131. Bushnell, D. PANDA2-program for minimum weight design of stiffened, composite, locally buckled panels. Computers and Structures, 1987, 25, 469-605.
132. Bushnell, D. Non-linear equilibrium of imperfect, locally deformed stringer-stiffened panels under combined in-plane loads. Computers and Structures, 1987, 27, 519-539.
133. Peng, M. and Sridharan, S. An optimization strategy for wide stiffened plates subject to interaction of local and overall buckling. Computers and Structures, 1991, 41, 233-243.
134. Tvergaard, V. Influence of post buckling behaviour on the optimum design of stiffened panels. International Journal of Solids Structures, 1973, 9, 1519-1534.
135. Tvergaard, V. Imperfection sensitivity of a wide integrally stiffened panels under compression. International Journal of Solids Structures, 1973, 9, 177-192.
136. Koiter, W. T. and Pignataro, M., A general theory for the interaction between local and overall buckling of stiffened panels. WTHD Report 83, Delft University of Technology, the Netherlands, 1976.
137. Van der Neut, A., Mode interaction with stiffened panels. In Buckling of Structures, IUTAM Symposium, ed. B. Budiansky, Cambridge, MA., Springer, Berlin, 1977, pp. 117-132.
138. Thompson, J. M., Tulk, J. D. and Walker, A. C., An experimental study of imperfection sensitivity in the interactive buckling of stiffened plates. In Buckling Of Structures, IUTAM Symposium, ed. B. Budiansky, Cambridge, MA. Springer, Berlin, 1977, pp. 149-159.
139. Gill, P. E., Murray, W. and Wright, M. H., Practical Optimization. Academic Press, London, 1981.
140. Schittkowski, K. A unified outline of non-linear programming algorithms. Journal of Mechanisms, Transmissions and Automation in Design, 1985, 107, 449-453.
141. Kloppel, E. K. and Scheer, I., Beulwerte Ausgesteifter Rechteckplatten Kurventafeln Zum Direkten Nachweis Der Beulsicherheit Fur Verschiedene Steifenanordnungen Und Belastungen. Von Wilhelm Ernst, Berlin, 1960.
142. Plank, R. J. and Williams, F. W., Critical buckling of some stiffened panels in compression, shear and bending. Aeronautical Quarterly, 1974, 165-179.
143. Stroud, W. J., Green, W. H. and Anderson, M. S., Buckling loads for stiffened panels subjected to combined longitudinal compression and shear loadings: results obtained with PASCO, EAL and STAGS computer programs. NASA TM 83194, 1981.