An experimental study of turbine vane heat transfer with water-air cooling

Journal of Turbomachinery

Volumn 120, Issue 1, 1998, Pages 50-60

  Nirmalan, N V ^a   Weaver, J A ^a   Hylton, L D ^a  

^a ROLLS ROYCE CORPORATION   (United States)

Author keywords

[No Author keywords available]

Indexed keywords

COOLING; HEAT TRANSFER; TURBINE; VANE;

EID: 0031921518     PISSN: 0889504X     EISSN: 15288900     Source Type: Journal    
DOI: 10.1115/1.2841387     Document Type: Article

References (13)

1. Biesiadny, T. J., Klann, G. A., Clark, D. A., and Berger, B. 1987. “Contingency Power for Turbo Small Turboshaft Engines Using Water Injection Into Turbine Cooling Air,” NASA TM 89817, AIAA Paper No. 87-1906.
2. Dudley, J. C., Sundell, R. E., Goodwin, W. W., and Kercher, D. M., 1984, “Two-Phase Heat Transfer in Gas Turbine Bucket Cooling Passages: Part 1,” in: Heat and Mass Transfer in Rotating Machinery, Metzer and Agfan, eds., Hemisphere Publishing Corporation, pp. 463-472.
3. Fiszdon, J. K., Florschuetz, L. W., and Janssen, J. M., 1994, “Heat Transfer to Two-Phase Air/Water Mixtures Flowing in Small Tubes With Inlet Disequilibrium,” in: Heat Transfer in Gas Turbines, Chyu and Nirmalan, eds., ASME HTD-Vol. 300, pp. 165-171.
4. Hylton, L. D., Nirmalan, N. V., and Sweeney, P. C., 1995, “Advanced Cooling Concept,” NASA Contractor Report, Preliminary Draft, Allison EDR 16666.
5. Kline, S. J., and McClintock, F. A., 1953. “Describing Uncertainties in SingleSample Experiments,” Mechanical Engineering, Jan., pp. 3-8.
6. Nealy, D. A., Mihelc, M. S., Hylton, L. D., and Gladden, H. J., 1984, “Measurements of Heat Transfer Distribution Over the Surfaces of Highly Loaded Turbine Nozzle Guide Vanes,” ASME Journal of Engineering for Gas Turbines and Power, Vol. 106, pp. 149-158.
7. Nirmalan, N. V., and Hylton, L. D., 1990, “An Experimental Study of Turbine Vane Heat Transfer With Leading Edge and Downstream Film Cooling,” ASME Journal of Turbomachinery, Vol. 112, pp. 477-487.
8. Pedersen, C. O., 1970, “An Experimental Study of the Dynamic Behavior and Heat Transfer Characteristics of Water Droplets Impinging Upon a Heated Surface,” International Journal of Heat and Mass Transfer, Vol. 13, pp. 369-381.
9. Schmidt, E., 1951, “Heat Transmission by Natural Convection at High Centrifugal Accelerations in Water-Cooled Gas Turbine Rotor Blades,” Institute of Mechanical Engineers Proceeding, Vol. 185, pp. 219-222.
10. Sundell, R. E., Dudley, J. C., Grondhal, C. M., and Kercher, D. M., 1984, “Two-Phase Heat Transfer in Gas Turbine Bucket Cooling Passages: Part 2,” in: Heat and Mass Transfer in Rotating Machinery, Metzer and Agfan, eds., Hemisphere Publishing Corporation, pp. 473-484.
11. Van Fossen, G. J., and Stepka, F. S., 1979, “Review and Status of Liquid Cooling Technology for Gas Turbines,” NASA RP 1038.
12. Van Fossen, G. J., 1983, “The Feasibility of Water Injection Into the Turbine Coolant to Permit Gas Turbine Contingency Power for Helicopter Application,” ASME Journal of Engineering for Power, Vol. 105, pp. 635-642.
13. Wenglarz, R. A., Nirmalan, N. V., and Daehler, T. G., 1995, “Rugged ATS Turbines for Alternate Fuels,” ASME Paper No. 95-GT-73.