Effect of plenum crossflow on heat (Mass) transfer near and within the entrance of film cooling holes

Journal of Turbomachinery

Volumn 119, Issue 4, 1997, Pages 761-769

  Goldstein, R J ^a   Cho, H H ^b   Jabbari, M Y ^c  

^a University of Minnesota   (United States)

^b Yonsei University   (South Korea)

^c SAGINAW VALLEY STATE UNIVERSITY   (United States)

Author keywords

[No Author keywords available]

Indexed keywords

COOLING; CROSSFLOW; FILM; GAS TURBINE; HEAT TRANSFER;

EID: 0031457515     PISSN: 0889504X     EISSN: 15288900     Source Type: Journal    
DOI: 10.1115/1.2841186     Document Type: Article

References (13)

1. Acrivos, A., Babcock, B. D., and Pigford, R. L., 1959, “Flow Distributions in Manifolds,” Chemical Engineering Science, Vol. 10, pp. 112-124.
2. Ambrose, D., Lawrenson, I. J., and Sparke, C. H. S., 1975, “The Vapor Pressure of Naphthalene,” J. Chem. Thermodynam., Vol. 7, pp. 1173-1176.
3. Byerley, A. R., Ireland, P. T., Jones, T. V., and Ashton, S. A., 1988, “Detailed Heat Transfer Measurements Near and Within the Entrance of a Film Cooling Hole,” ASME Paper No. 88-GT-155.
4. Cho, H. H., 1992, “Heat/Mass Transfer Flow Through an Array of Holes and Slits,” Ph.D. Thesis, University of Minnesota.
5. Cho, H. H., and Goldstein, R. J., 1995, “Heat (Mass) Transfer and Film Cooling Effectiveness With injection Through Discrete Holes: Part I-Within Holes and on the Back Surface,” ASME Journal of Turbomachinery, Vol. 117, pp. 440-450.
6. Fried, E., and Idelchik, I. E., 1989, Flow Resistance: A Design Guide for Engineers, 2nd ed., Hemisphere Publishing Corp., pp. 248-251.
7. Goldstein, R. J., and Cho, H. H., 1995, “A Review of Mass Transfer Measurements Using Naphthalene Sublimation,” Experimental Thermal and Fluid Science, Vol. 10, pp. 416-434.
8. Kline, S. J., and McClintock, F. A., 1953, “Describing Uncertainty in SingleSample Experiments,” Mech. Engineering, Vol. 75, Jan., pp. 3-8.
9. Metzger, D. E., and Cordaro, J. V., 1979, “Heat Transfer in Short Tubes Supplies From a Cross-Flowing Stream,” ASME Paper No. 79-WA/HT-16.
10. Miller, D. S., 1990, Internal Flow Systems: Design and Performance Prediction, 2nd ed., Gulf Publishing Company, pp. 71-87, 303-361.
11. Mills, A. F., 1962, “Experimental Investigation of Turbulent Heat Transfer in the Entrance Region of a Circular Conduit,” J. Mech. Eng. Sci., Vol. 4, pp. 6377.
12. Sparrow, E. M., and Kermink, R. G., 1979, “Heat Transfer Downstream of a Fluid Withdrawal Branch in a Tube,” ASME Journal of Heat Transfer, Vol. 101, pp. 23-28.
13. Wesley, D. A., and Sparrow, E. M., 1976, “Circumferentially Local and Average Turbulent Heat-Transfer Coefficients in a Tube Downstream of a Tee,” Int. J. Heat Mass Transfer, Vol. 19, pp. 1205-1213.