Derivation of hydrodynamic bearing coefficients using the minimum square method

Journal of Tribology

Volumn 119, Issue 4, 1997, Pages 802-807

  Muller Karger, Carmen M ^a   Granados, Andres L ^a  

^a UNIVERSIDAD SIMÓN BOLÍVAR   (Venezuela)

Author keywords

[No Author keywords available]

Indexed keywords

HYDRODYNAMICS; JOURNAL BEARING; MATHEMATICAL MODELING;

EID: 0031446384     PISSN: 07424787     EISSN: 15288897     Source Type: Journal    
DOI: 10.1115/1.2833888     Document Type: Article

References (15)

1. Branagan, L. A., 1988, “Thermal Analysis of Fixed and Tilting Pad Journal Bearings Including Cross-Film Viscosity Variations and Deformations,” Doctoral Dissertation, University of Virginia.
2. Brockwell, K., Kleinbub, D., and Dmochowski, W., 1990, “Measurement and Calculations of Dynamic Operation Characteristics of the Five Shoe, Tilting Pad, Journal Bearing,” Tribology Transactions, Trans. ASLE, Vol. 33, No. 4, pp. 481-492.
3. Dowson, D., and Taylor, C. M. 1980, “The State of Knowledge in the Field of Bearing-Influenced Rotor Dynamics,” Tribol. Int., Vol. 13, pp. 176-178.
4. Glienicke, K., 1966-1967, “Experimental Investigation of the Stiffness and Damping Coefficients of Turbine and Their Application to Instability Prediction,“ Proc. Instn. Meek. Engr., Vol. 181, Part 3B, Paper 13, pp. 116-129.
5. Hagg, A. C., and Sankey, G. O., 1956, “Some Dynamic Properties of Oil Film Journal Bearing with Reference to Unbalance Vibration of Rotor,” ASME Journal of Applied Mech., Vol, 78, pp. 302-306.
6. Hattori, H., 1993, “Dynamic Analysis of a Rotor-Journal Bearing System with Large Dynamic Loads (Stiffness and Damping Coefficient Variations in Bearing Oil Film),” JSME International Journal, Vol. 36, No. 2, pp. 251-257.
7. Knight, J. D., and Barrett, L. E., 1983, “An Approximate Solution Technique for Multilobe Journal Bearing Including Theraml Effects, with Comparison to Experiment,” Trans. ASLE, Vol. 26, No. 4, pp. 501-508.
8. Knight, J. D., and Barrett, L. E., 1987, “Analysis of Axially Grooved Journal Bearings with Heat Transfer Effects,” Trans. ASLE, Vol. 30, No. 3, pp. 316-323.
9. Kostrzewsky, G. J., and Flack, R. D., 1990a, “Accuracy Evaluation of Experimental Derived Dynamic Coefficients of Fluid Film Bearings, Part I: Development of the Method,” Tribology Transactions, Trans. ASLE, Vol. 33, No. 1, pp. 105-114.
10. Kostrzewsky, G. J., and Flack, R. D., 1990b, “Accuracy Evaluation of Experimental Derived Dynamic Coefficients of Fluid Film Bearings, Part II: Cases Studies,” Tribology Transactions, Trans. ASLE, Vol. 33, No. 1, pp. 115-121.
11. Lund, J. W., and Hansen, P. K., 1984, “An Approximate Analysis of the Temperature Conditions in Journal Bearing. Part I: Theory,” ASME Journal of Tribology, Vol. 106, pp. 228-236.
12. Müller-Karger, C. M., 1994, “Non-Linearities in Bearing Measurements,” M.Sc. thesis, University of Virginia.
13. Stanway, R., 1987, “Estimation of Linearized Damping Coefficients of a Squeeze-Film Vibration Isolator,” Proc. Inst. Mech. Engrs., Vol. 201, No. C3, pp. 181-191.
14. Stanway, R., Mottershead, J. E., and Firoozian, R., 1988, “Nonlinear Identification of Squeeze-Film Damper,” ASME Journal of Tribology, Vol. 1110, pp. 486-491.
15. Tonnesen, J., 1976, “Experimental Parametric Study of a Squeeze-Film Bearing,” ASME Journal Lubrication Technology, Vol. 98, pp. 206-213.