Influence of solid loading and particle size distribution on the porosity development of green alumina ceramic mouldings

Ceramics International

Volumn 23, Issue 6, 1997, Pages 513-520

  Liu, Dean Mo ^a  

^a INDUSTRIAL TECHNOLOGY RESEARCH INSTITUTE   (Taiwan)

Author keywords

[No Author keywords available]

Indexed keywords

CERAMIC MATERIALS; COMPACTION; COMPRESSION MOLDING; PARTICLE SIZE ANALYSIS; POROSITY; POWDERS;

CERAMIC MOLDINGS; COMPRESSIVE STRESS;

ALUMINA;

EID: 0031377298     PISSN: 02728842     EISSN: None     Source Type: Journal    
DOI: 10.1016/S0272-8842(96)00063-6     Document Type: Article

References (20)

1. GERMAN, R. M., Powder Injection Moulding. Metal Powder Industries Federation, Princeton, NJ, 1990.
2. GERMAN, R. M., HENS, K. F. & PAUL LIN, S. T., Key issues in powder injection moulding. Am. Ceram. Soc. Bull., 70(8) (1991) 1294-1302.
3. EDIRISINGHE, M. J., Proc. Brit. Ceram. Soc., 45 (1990) 109.
4. HUNT, K. M., EVANS, J. R. G. & WOODTHORPE, J., The influence of mixing route on the properties of ceramic injection moulding blends. Brit. Ceram. Trans. J., 87 (1988) 17-21.
5. THOMAS, M. S. & EVANS, J. R. G., Non-uniform shrinkage in ceramic injection moulding. Brit. Ceram. Trans. J., 87 (1988) 22-26.
6. BANDYOPADHYAY, G. & FRENCH, K. W., Injection-moulded ceramics: Critical aspects of the binder removal process and component fabrication. J. Eur. Ceram. Soc., 11 (1993) 23-34.
7. EVANS, J. R. G. & EDIRISINGHE, M. J., Interfacial factors affecting the incidence of defects in ceramic mouldings. J. Mater. Sci., 26 (1991) 2081-2088.
8. SHAW, H. M. & EDIRISINGHE, M. J., Porosity development during removal of organic vehicle from ceramic injection mouldings. J. Eur. Ceram. Soc., 13 (1994) 135-142.
9. MATAR, S. A., EDIRISINGHE, M. J., EVANS, J. R. G. & TWIZELL, E. H., The effect of porosity development on the removal of organic vehicle from ceramic or metal mouldings. J. Mater. Res., 8(3) (1993) 617-625.
10. EVANS, J. R. G., EDIRISINGHE, M. J., WRIGHT, T. K. & CRANK, J., On the removal of organic vehicle from moulded ceramic bodies. Proc. Royal Soc. ( London), A432 (1991) 321-340.
11. SHAW, H. M., HUTTON, T. J. & EDIRISINGHE, M. J., On the formation of porosity during removal of organic vehicle from injection moulded ceramic bodies. J. Mater. Sci. Lett., 11 (1992) 1075-1077.
12. ALLAIRE, F., MARPLE, B. R. & BOULANGER, J., Injection moulding of submicrometer zirconia: Blend formulation and rheology. Ceram. Int., 20 (1994) 319-325.
13. PAUL LIN, S. T. & GERMAN, R. M., The influence of powder loading and binder additive on the properties of alumina injection-moulding bodies. J. Mater. Sci., 29 (1994) 5367-5373.
14. CALVERT, P. & CIMA, M., Theoretical models for binder burnout. J. Am. Ceram. Soc., 73 (1989) 575-579.
15. EDIRISINGHE, M. J. & EVANS, J. R. G., Review: Fabrication of engineering ceramics by injection moulding - I. Materials selection. Int. J. High Temp. Ceram., 2 (1986) 1-31.
16. MANGELS, J. A. & WILLIAMS, R. M., Injection moulding ceramics to high green densities. Am. Ceram. Soc. Bull., 62(5) (1983) 601-606.
17. POLINSKI, A. J., RYAN, M. E., GUPTA, R. K., SESHADRI, S. G. & FRECHETTE, F. J., Rheological behaviour of filled polymeric systems - II. The effect of a bimodal size distribution of particulates. J. Rheol., 32 (1988) 751-771.
18. LIU, D. M. & FU, C. T., Rheological behaviour and green microstructure of slip-cast silicon carbide ceramics. Ceram. Int., 22 (1996) 101-106.
19. LIU, D. M., LIN, B. W. & FU, C. T., Effect of preparation condition on the slurry structure and green compact property of slip-cast silicon carbide ceramic. J. Ceram. Soc. Jpn, in press.
20. CUMBERLAND, D. J. & CRAWFORD, R. J., The Packing of Particles. Elsevier, Amsterdam, 1987.