Plastic buckling approximation for transition ringbeams in steel silos

Journal of Structural Engineering

Volumn 123, Issue 12, 1997, Pages 1622-1630

  Teng, J G ^a  

^a HONG KONG POLYTECHNIC UNIVERSITY   (Hong Kong)

Author keywords

[No Author keywords available]

Indexed keywords

APPROXIMATION THEORY; BEAMS AND GIRDERS; BUCKLING; PLASTIC DEFORMATION; RINGS (COMPONENTS); STRENGTH OF MATERIALS; TANKS (CONTAINERS);

PLASTIC BUCKLING;

STEEL STRUCTURES;

EID: 0031375434     PISSN: 07339445     EISSN: None     Source Type: Journal    
DOI: 10.1061/(ASCE)0733-9445(1997)123:12(1622)     Document Type: Article

References (21)

1. Galletly, G. D. (1985). "Torispherical shells." Shell structures: stability and strength, R. Narayanan, ed., Elsevier Applied Science, New York, N.Y.
2. Galletly, G. D., and Blachut, J. (1985). "Torispherical shells under internal pressure-failure due to asymmetric buckling or axisymmetric yielding." Proc., Inst. of Mech. Engrs., 1999(C3), 225-228.
3. Gaylord, E. H., and Gaylord, C. N. (1984). Design of steel bins for storage of bulk solids. Prentice Hall, Inc., Englewood Cliffs, N.J.
4. Greiner, R. (1991). "Elastic plastic buckling at cone cylinder junctions of silos." Buckling of shell structures on land, in the sea and in the air, J. F. Jullien, ed., Elsevier Applied Science, New York, N.Y.
5. Janssen, H. A. (1895). "Versuche uber getreidedruck in silozellen." Zeitschrift des vareines Deutscher Ingenieure, 29(35), 1045-1049.
6. Jumikis, P. T. (1987). "Stability problems in silo structures," PhD thesis, School of Civ. and Min. Engrg., Univ. of Sydney, Australia.
7. Jumikis, P. T., and Rotter, J. M. (1983). "Buckling of simple ringbeams for bins and tanks." Proc., Int. Conf. on Bulk Mat. Storage, Handling and Transp., Inst. of Engrs., Newcastle, Australia, Aug., 323-328.
8. Rotter, J. M. (1985). "Analysis and design of ringbeams." Design of steel bins for the storage of bulk solids, School of Civ. and Min. Engrg., Univ. of Sydney, Australia., March, 164-183.
9. Rotter, J. M. (1987). "The buckling and plastic collapse of ring stiffeners at cone/cylinder junctions." Proc., Int. Colloquium on the Stability of Plate and Shell Struct., Gent, Belgium, April, ECCS, 449-456.
10. Rotter, J. M. (1996). "Shell structures: design standards, recent progress and unsolved problems." Advances in steel structures, S. L. Chan and J. G. Teng, eds., Elsevier Science Publishing Co. Inc., New York, N.Y.
11. Sharma, U. C., Rotter, J. M., and Jumikis, P. T. (1987). "Shell restraint to ringbeam buckling in elevated steel silos." Proc., 1st Nat. Struct. Engrg. Conf., Inst. of Engrs., Australia, Aug., 604-609.
12. Teng, J. G. (1994). "Cone-cylinder intersection under internal pressure: axisymmetric failure." J. Engrg. Mech., ASCE, 120(9), 1896-1912.
13. Teng, J. G. (1996). "Buckling of thin shells: recent advances and trends." Appl. Mech. Rev., 49(4), 263-274.
14. Teng, J. G. (1997). "On the buckling strength of ringbeams in steel silos." Presented at the Int. Conf. on Carrying Capacity of Steel Shell Struct., Oct. 1-3, 1997, Brno, Czech Republic.
15. Teng, J. G., and Rotter, J. M. (1989). "Non-symmetric bifurcation of geometrically non-linear elastic-plastic axisymmetric shells subject to combined loads including torsion." Comp. and Struct., 32(2), 453-477.
16. Teng, J. G., and Rotter, J. M. (1991a). "The collapse behavior and strength of steel silo junctions-Parts I and II." J. Struct. Engrg., ASCE, 117(12), 3587-3622.
17. Teng, J. G., and Rotter, J. M. (1991b). "Plastic buckling of rings at steel silo transition junctions." J. Constr. Steel Res., 19, 1-18.
18. Teng, J. G., and Rotter, J. M. (1991c). "Strength of welded steel silo hoppers under filling and flow pressures." J. Struct. Engrg., ASCE, 117(9), 2567-2583.
19. Trahair, N. S., Abel, A., Ansourian, P., Irvine, H. M., and Rotter, J. M. (1983). "Structural design of steel bins for bulk solids." Australian Inst. of Steel Construct., Sydney.
20. Walker, D. M. (1966). "An approximate theory for pressure and arching in hoppers." Chemical Engrg. Sci., 21, 975-997.
21. Wozniak, R. S. (1979). "Steel tanks." Structural engineering handbook, 2nd Ed., Sect. 23, E. H. Gaylord and C. N. Gaylord, eds., McGraw-Hill Inc., New York, N.Y.