Extremal overall elastic response of polycrystalline materials

Journal of the Mechanics and Physics of Solids

Volumn 45, Issue 11-12, 1997, Pages 1765-1780

  Bendsøe, Martin P ^a   Lipton, Robert ^b  

^a TECHNICAL UNIVERSITY OF DENMARK   (Denmark)

^b Worcester Polytechnic Institute   (United States)

Author keywords

A. microstructures; B. anisotropic material; B. polycrystalline material; C. variational calculus

Indexed keywords

ANISOTROPY; CRYSTAL MICROSTRUCTURE; ELASTICITY; SINGLE CRYSTALS; STRAIN; STRESS CONCENTRATION; VARIATIONAL TECHNIQUES;

EXTREMAL OVERALL ELASTIC RESPONSE;

POLYCRYSTALLINE MATERIALS;

EID: 0031271994     PISSN: 00225096     EISSN: None     Source Type: Journal    
DOI: 10.1016/S0022-5096(97)00032-X     Document Type: Article

References (16)

1. Allaire, G. and Kohn, R. V. (1993) Optimal design for minimum weight and compliance in plane stress using extremal microstructures. Eur. J. Mech. A 12, 839-878.
2. Avellaneda, M., Cherkaev, A. V., Gibiansky, L. V., Milton, G. W. and Rudelson, M. (1995) A complete characterization of the possible bulk and shear moduli of planar polycrystals. Preprint.
3. Avellanda, M. and Milton, G. W. (1989a) Bounds on the effective elasticity tensor composites based on two-point correlation. In Composite Material Technology, ed. D. Hui and T. J. Kozik, pp. 89-93. ASME, New York.
4. Avellaneda, M. and Milton, G. W. (1989b) Optimal bounds on the effective bulk modulus of polycrystals. SIAM J. Appl. Math. 49, 824-837.
5. Cheng, G. and Pedersen, P. (1997) On sufficiency conditions for optimal design based on extremum principles of mechanics. J. Mech. Phys. Solids 45, 135-150.
6. Fedorov, A. V. and Cherkaev, A. V. (1983) Choice of optimal orientation of axes of elastic symmetry for an orthotropic plate. MTT 18, 135-142.
7. Fukanaga, H. and Sekine, H. (1992) Stiffness design method of symmetric laminates using lamination parameters. AIAA J. 30, 2791-2793.
8. Hammer, V. B., Bendse, M. P., Lipton, R. and Pedersen, P. (1997) Parametrization in laminate design for optimal compliance. Int. J. Solids Struct. 34, 415-434.
9. Hashin, Z. and Shtrikman, S. (1962) A variational approach to the theory of the elastic behaviour of polycrystals. J. Mech. Phys. Solids 10, 343-352.
10. Pedersen, P. (1989) On optimal orientation of orthotropic materials. Struct. Optim. 1, 101-106.
11. Rovati, M. and Taliercio, A. (1991) Optimal orientation of the symmetry axes of orthotropic 3-D materials. In Proc. Int. Conf. Engineering Optimization in Design Processes, ed. H. A. Eschenauer, C. Mattheck and N. Olhoff. Lecture Notes in Engineering, 63, pp. 127-134. Springer Verlag, Berlin.
12. Rudelson, M. (1989) Phase transitions in solids. Master's thesis, St Petersburg Technical University, St Petersburg, Russia.
13. Seregin, G. A. and Troitskii, V. A. (1982) On the best position of elastic symmetry planes in an orthotropic body. PMM USSR 45, 139-142.
14. Stroud, D. (1975) Generalized effective medium approach to the conductivity of an inhomogeneous material. Phys. Rev. B. 12, 3368-3373.
15. Tsai, S. W. and Hahn, H. T. (1980) Introduction to Composite Materials. Technomic Press, Lancaster, PA.
16. Willis, J. R. (1982) Elasticity theory of composites. In Mechanics of Solids ed. H. G. Hopkins and M. J. Sewell. pp. 653-685. Pergamon Press, Oxford.