Three-dimensional cutting process analysis with different cutting velocities

Journal of Materials Processing Technology

Volumn 70, Issue 1-3, 1997, Pages 22-33

  Lin, Zone Ching ^a   Yarng, Yuung Der ^a  

^a NATIONAL TAIWAN UNIVERSITY OF SCIENCE AND TECHNOLOGY   (Taiwan)

Author keywords

Cutting; Elastic plastic; Three dimensional

Indexed keywords

CARBON STEEL; ELASTOPLASTICITY; FINITE ELEMENT METHOD; MATHEMATICAL MODELS; RESIDUAL STRESSES; STRAIN; STRESS CONCENTRATION;

CUTTING FORCES; STRAIN ENERGY DENSITY;

METAL CUTTING;

EID: 0031259337     PISSN: 09240136     EISSN: None     Source Type: Journal    
DOI: 10.1016/S0924-0136(97)00036-8     Document Type: Article

References (17)

1. M.E. Merchant, Mechanics of the metal cutting process, J. Appl. Phys. 16 (1945) 267-318.
2. L.E. Lee, B.W. Shaffer, The theory of plastic applies to a problem of machining, Trans. ASME, J. Appl. Mech. 18 (1951) 405-413.
3. M.R. Lajczok, A study of some aspects of metal machining using the finite element method, Ph.D. dissertation, NC State University, 1980.
4. E. Usui, T. Shirakashi, Mechanics of machining - from descriptive to predictive theory, in: On the Art of Cutting Metals 75 Years Later: A Tribute to F.W. Taylor, 1982, pp. 13-30.
5. K. Iwata, K. Osakada, T. Terasaka, Process modeling of orthogonal cutting by the rigid-plastic finite element method, Trans. ASME, J. Eng. Mater. Technol. 106 (1984) 132-138.
6. J.S. Strenkowski, J.T. Carroll III, A finite element model of orthogonal metal cutting, Trans. ASME, J. Eng. Ind. 107 (1985) 349-354.
7. J.S. Strenkowski, G.L. Mitchum, An improved finite element method of orthogonal metal cutting, in: Proc. North American Manufacturing Research Conference, Bethlehem, Pennsylvania, 1987, pp. 506-509.
8. J.S. Strenkowski, Kyoung-Jin Moon, Finite element prediction of chip geometry and tool/workpiece temperature distributions in orthogonal metal cutting, Trans. ASME, J. Eng. Ind. 127 (1990) 313-318.
9. E. Usui, K. Maekawa, T. Shirakashi, Simulation analysis of built-up edge formation in machining of low carbon steel, Bull. Jpn. Soc. Prec. Eng. 15 (4) (1981) 237-242.
10. J. Hashemi, P.C. Chou, A.A. Tseng, Thermomechanical behavior of adiabatic shear band in high speed forming and machining, in: XXXII 1 CHMT Int. Symp. on Manufacturing and Materials Processing, Dubrovnik, Yugoslavia, 27 August, 1990.
11. C.R. Liu, M.M. Barash, The mechanical state of the sublayer of a surface generated by chip removal process, part 2: cutting with a tool with flank wear, ASME, J. Eng. Ind. 98 (1976) 1102-1108.
12. Shan. Tiarn. Jia. Jau., The foundation of non-linear finite element method, in: Yah Dung Book, Taipei, 1989, pp. 134-136.
13. Z.C. Lin, C.J. Lee, A coupled analysis of the thermo-elastic-plastic large deformation for upsetting process, J. Chin. Soc. Mech. Eng. 10 (3) (1989) 197-209.
14. S.S. Rao, The Finite Element Method in Engineering, 2nd edn., Pergamon, UK, 1989.
15. T. Shirakashi, K. Maekawa, E. Usui, Flow stress of low carbon steel at high temperature and strain rate, Bull. Jpn. Soc. Prec. Eng. 17 (1983) 167-172.
16. Z.C. Lin, S.Y. Lin, A coupled finite element model of thermo-elastic-plastic large deformation for orthogonal cutting, Trans. ASME, J. Eng. Mater. Technol. 114 (1992) 218.
17. Z.C. Lin, Y.T. Lin, F.S. Chang, The effect of tool flank wear on the temperature distribution of a machined workpiece, J. Chin. Inst. Eng. 10 (4) (1987) 353-362.