Computer animation of 3-d chip formation in oblique machining

Journal of Manufacturing Science and Engineering, Transactions of the ASME

Volumn 119, Issue 3, 1997, Pages 433-438

  Fang, X D ^a   Fang, Y J ^b   Hamidnia, S ^b  

^a Iowa State University   (United States)

^b UNIVERSITY OF WOLLONGONG   (Australia)

Author keywords

[No Author keywords available]

Indexed keywords

ANIMATION; COMPUTATIONAL GEOMETRY; COMPUTER AIDED DESIGN; KNOWLEDGE BASED SYSTEMS; MICROPROCESSOR CHIPS; THREE DIMENSIONAL;

CHIP FORMATION;

COMPUTER GRAPHICS;

EID: 0031207769     PISSN: 10871357     EISSN: 15288935     Source Type: Journal    
DOI: 10.1115/1.2831124     Document Type: Article

References (16)

1. Fang, X. D., and Jawahir, I. S., 1990, “An Expert System Based on A Fuzzy Mathematical Model for Chip Breakability Assessments in-Automated Machining,” ASME Proc. Int. Conf. Ml'90, Atlanta, GA, Vol. 4, pp. 31-37.
2. Hahn, R. S., 1953, “Some Observations on Chip Curl in the Metal-Cutting Process Under Orthogonal Cutting Conditions,” Transactions of the ASME, May, pp. 581-590.
3. Henriksen, E. K., 1953, “Chip Breaking: A Study of Three-Dimensional Chip Flow,” ASME Paper, 53-S-9.
4. Jawahir, I. S., and van Lutterveit, C. A., 1993, “Recent Developments in Chip Control Research and Applications,” Annals of the CIRP, Vol. 42, No. 2, pp. 659-685.
5. Jawahir, I. S., 1990, “On 1the Controllability of Chip Breaking Cycles and Modes of Chip Breaking in Metal Machining,” Annals of the CIRP, Vol. 39, No. 1, pp. 47-51.
6. Kane G. E., 1987, “An Approach to the Breaking of Chips,” Proc. The Conference on Advances in Tool Materials for Use in High Speed Machining, February 25-27, 1987, Scottsdale, AZ, pp. 29-37.
7. Kudo, H., 1965, “Some New Slip-line Solutions for Two-dimensional Steady-State Machining,” Int. J. Mech. Sci., Vol. 7, pp. 43-55.
8. Nakayama, K., and Ogawa, M., 1978, “Basic Rules on the Form of Chip in Metal Cutting,” Annals of the CIRP, Vol. 27, No. 1, pp. 17-21.
9. Nakayama, K., and Arai, M., 1992, “Comprehensive Chip Form Classification based on the Cutting Mechanism,” Annals of the CIRP, Vol. 41, No. 1, pp. 71-74.
10. Nakayama, S., Wuebbling, G. J., and Christopher, J. D., 1982, “Chip Control in Turning,” Proc. SME International Tool & Manufacturing Engineering Conference, Detroit, pp. 159-177.
11. Pekelharing, A. J., 1964, “Why and How does the Chip Curl and Break,” Annals of the CIRP, Vol. 12, No. 1, pp. 144-147.
12. Shin, Y. C., and Betts, C. A., 1993, “Control of Chips in the Turning of 4150 by Using an Obstruction Type Chip Breaker,” ASME Journal of Engineering for Industry, Vol. 115, pp. 160-163.
13. Sppans, C., 1971, “The Fundamentals of Three-Dimensional Chip Curl, Chip Breaking and Chip Control,” PhD Thesis, TH Delft.
14. van Lutterveit, C. A., 1989, “Evaluation of Present Possibility of Chip Control,” VDI Berichte NR. 762, pp. 181-200.
15. Worthington, B., and Redford, A. H., 1973, “Chip Curl and the Action of the Groove Type Chip Former,” Int. J. Mach. Tool Des. Res., Vol. 13, pp. 257-270.
16. Yao, Y., Jawahir, I. S., Jamieson, D., and Fang, X. D., 1990, “Computer Animation of Chip Flow and Chip Curl in an Expert Process Planning System for Metal Machining,” Transactions of the NAMR1/SME, SME Publ, pp. 161-166.