Row-of-Holes film cooling of curved walls at low injection angles

Journal of Turbomachinery

Volumn 119, Issue 3, 1997, Pages 574-579

  Goldstein, R J ^a   Stone, L D ^a  

^a UNIVERSITY OF MINNESOTA   (United States)

Author keywords

[No Author keywords available]

Indexed keywords

BOUNDARY LAYERS; COOLING; EFFICIENCY; FILMS; FLOW INTERACTIONS; FLOW VISUALIZATION; VORTEX FLOW;

FILM COOLING;

ADIABATIC ENGINES;

COOLING; FILMS; FLOW VISUALIZATION; GAS FLOW; WALLS;

EID: 0031191195     PISSN: 0889504X     EISSN: 15288900     Source Type: Journal    
DOI: 10.1115/1.2841160     Document Type: Article

References (21)

1. Cho, H. H., 1994, personal communication.
2. Eckert, E. R. G., 1983, “Analysis of Film Cooling and Full-Coverage Film Cooling of Gas Turbine Blades,” ASME Paper No. 83-GTJ-2.
3. Eckert, E. R. G., 1976, “Analogies to Heat Transfer Processes,” Measurements in Heat Transfer, 2nd ed., Ernst R. G. Eckert and Richard J. Goldstein, eds., Hemisphere Publishing Corp., Washington, DC.
4. Foster, N. W., and Lampard, D., 1980, “The Flow and Film Cooling Effectiveness Following Injection Through a Row of Holes,” ASME Journal of Engineering for Power, Vol. 102, pp. 584-588.
5. Goldstein, R. J., Eckert, E. R. G., Eriksen, V. L., and Ramsey, J. W., 1970, “Film Cooling Following Injection Through Inclined Circular Tubes,” Israel J. Technology, Vol. 108, pp. 145-154.
6. Goldstein, R. J., and Taylor, J. R., 1982, “Mass Transfer in the Neighborhood of Jets Entering a Crossflow,” ASME Journal of Heat Transfer, Vol. 104, pp. 715-721. '
7. Goldstein, R. J., and Stone, L. D., 1994, “Row-of-Holes Film Cooling of a Convex and a Concave Wall at Low Injection Angles,” ASME HTD-Vol. 300, pp. 15-29.
8. Ito, S., Goldstein, R. J., and Eckert, E. R. G., 1978, “Film Cooling of a Gas Turbine Blade,” ASME Journal of Engineering for Power, Vol. 100, pp. 476-481.
9. Kim, J. H., Simon, T. W., and Viskanta, R., 1993, “Journal of Heat Transfer Policy on Reporting Uncertainties in Experimental Measurements and Results,” ASME Journal of Heat Transfer, Vol. 115, pp. 5-6.
10. Kline, S. J., and McClintock, F. A., 1953, “Describing Uncertainties in SingleSample Experiments,” Mechanical Engineering, Vol. 75, Jan., pp. 3-8.
11. Kruse, H., 1985, “Effects of Hole Geometry, Wall Curvature and Pressure Gradient on Film Cooling Downstream of a Single Row,” Heat Transfer and Cooling in Gas Turbines, AGARD-CP-390.
12. Mayle, R. E., Kopper, F. C., Blair, M. F., and Bailey, D. A., 1976, “Effect of Streamline Curvature on Film Cooling,” ASME Paper No. 76-GT-90.
13. Meroney, R. N., and Bradshaw, P., 1975, “Turbulent Boundary-Layer Growth Over a Longitudinally Curved Surface,” AIAA J., Vol. 13, pp. 1448-1453.
14. Moffat, R, J., 1982, “Contributions to the Theory of Single-Sample Uncertainty Analysis,” ASME Journal of Fluids Engineering, Vol. 104, pp. 250-260.
15. Pedersen, D. R., Eckert, E. R. G., and Goldstein, R. J., 1977, “Film Cooling With Large Density Differences Between the Mainstream and Secondary Fluid Measured by the Heat—Mass Transfer Analogy,” ASME Journal of Heat Transfer, Vol. 99, pp. 620-627.
16. Ramsey, J. W., and Goldstein, R. J., 1971, “Interaction of a Heated Jet With a Deflecting Stream,” ASME Journal of Heat Transfer, Vol. 93, pp. 365-372.
17. Schwarz, S. G., 1986, “Film Cooling of Curved Surfaces,” Ph.D. Thesis, University of Minnesota, Minneapolis, MN.
18. Schwarz, S. G., and Goldstein, R. J., 1989, “The Two-Dimensional Behavior of Film Cooling Jets on Concave Surfaces,” ASME Journal of Turbomachinery, Vol. HI, pp. 124-130.
19. Schwarz, S. G., Goldstein, R. J., and Eckert, E. R. G., 1990, “The Influence of Curvature on Film Cooling Performance,” ASME Journal of Turbomachinery, Vol. 100, pp. 472-478.
20. Stone, L. D., 1992, “Film Cooling of Curved Surfaces at Low Injection Angles,” M.S. Thesis, University of Minnesota, Minneapolis, MN.
21. Stone, L. D., and Goldstein, R. J., 1994, “Film Cooling Effectiveness Data for Simple Injection Geometries: A Collection of Three-Axis Plots,” Int. J. of Rotating Machinery, Vol. 1(1), pp. 73-81