Heat transfer augmentation in a rectangular channel with slit rib-Turbulators on two opposite walls

Journal of Turbomachinery

Volumn 119, Issue 3, 1997, Pages 617-623

  Hwang, Jenn Jiang ^a   Liou, Tong Miin ^b  

^a CHUNG HUA UNIVERSITY   (Taiwan)

^b NATIONAL TSING HUA UNIVERSITY   (Taiwan)

Author keywords

[No Author keywords available]

Indexed keywords

CHANNEL FLOW; CORRELATION METHODS; FRICTION; HEAT TRANSFER; HOLOGRAPHY; REYNOLDS NUMBER; SURFACE ROUGHNESS; TURBULENT FLOW;

RIBBED CHANNELS;

TURBOMACHINE BLADES;

CHANNELS; FRICTION; HEAT TRANSFER; REYNOLDS NUMBER; WALLS;

EID: 0031189495     PISSN: 0889504X     EISSN: 15288900     Source Type: Journal    
DOI: 10.1115/1.2841167     Document Type: Article

References (15)

1. Bergles, A. E., 1969, “Survey and Evaluation of Techniques to Augment Convective Heat and Mass Transfer,” Progress in Heat and Mass Transfer, Pergamon Press, Oxford, Vol. 1, pp. 331-324.
2. Burggraf, F., 1970, “Experimental Heat Transfer and Pressure Drop With TwoDimensional Discrete Turbulence Promoters Applied to Two Opposite Walls of a Square Tube,” Augmentation of Convective Heat and Mass Transfer, E. E. Bergles and R. L. Webb, eds., ASME, New York, pp. 70-79.
3. Chyu, M. K., and Wu, L. X., 1989, “Combined Effects of Rib Angle-of-Attack and Pitch-to-Height Ratio on Mass Transfer From a Surface With Transverse Ribs,” Experimental Heat Transfer, Vol. 2, pp. 291-308.
4. Dippery, D. F., and Sabersky, R. H., 1963, “Heat and Momentum Transfer in Smooth and Rough Tubes at Various Prandtl Number,” Int. J. Heat Mass Transfer, Vol. 6, pp. 329-353.
5. Han, J. C., Glicksman, L. R., and Rohsenow, W. M., 1978, “An Investigation of Heat Transfer and Friction for Rib-Roughened Surfaces,” Int. J. Heat Mass Transfer, Vol. 21, pp. 1143-1156.
6. Han, J. C., 1984, “Heat Transfer and Friction in Channels With Two Opposite Rib-Roughened Wall,” ASME Journal of Heat Transfer, Vol. 106, pp. 774-782.
7. Han, J. C., 1988, “Heat Transfer and Friction Characteristics in Rectangular Channels With Rib Turbulators,” ASME Journal of Heat Transfer, Vol. 110, pp. 321-328.
8. Kline, S. J., and McClintock, F. A., 1953, “Describing Uncertainties on SingleSample Experiments,” Mechanical Engineering, Jan., pp. 3-8.
9. Lau, S. C., McMillin, R. D., and Han, J. C., 1991, “Turbulent Heat Transfer and Friction in a Square Channel With Discrete Rib Turbulators,” ASME Journal of Turbomachinery, Vol. 113, pp. 360-366.
10. Liou, T. M., and Hwang, J. J., 1992a, “Turbulent Heat Transfer and Friction in Periodic Fully Developed Channel Flows,” ASME Journal of Heat Transfer, Vol. 114, pp. 56-64.
11. Liou, T. M., and Hwang, J. J., 1992b, “Developing Heat Transfer and Friction in a Ribbed Rectangular Duct With Flow Separated at Inlet,” ASME Journal of Heat Transfer, Vol. 114, pp. 565-573.
12. Liou, T M., and Hwang, J. J., 1993, “Effect of Ridge Shapes on Turbulent Heat Transfer and Friction in a Rectangular Channel,” Int. J. Heat Mass Transfer, Vol. 36, pp. 931-940.
13. Metzger, D. E., Vedula, R. P., and Breen, D. D., 1987, “Effects of Rib Angle and Length on Convection Heat Transfer in Rib-Roughened Triangular Duct,” Proc. ASME/JSME Thermal Engineering Joint Conference, Honolulu, HI, Vol. 3, ASME, New York, pp. 327-333.
14. Tanasawa, I., Nishio, S., Takano, K., and Miyazaki, H., 1984, “High-Performance Surface for Forced-Convection Heat Transfer Using Novel Turbulence Promoters,” ASME Paper No. 84-HT-69.
15. Webb, R. L., Eckert, E. R. G., and Goldstein, R. J., 1971, “Heat Transfer and Friction in Tubes With Repeated-Rib Roughness,” Int. J. Heat Mass Transfer, Vol. 14, pp. 601-617