Thermogravimetric and binder removal analysis of injection moulded reinforced ceramic composite

Composite Structures

Volumn 38, Issue 1-4, 1997, Pages 483-487

  Li, R K Y ^a   Wu, C M L ^a   Wong, T L ^a  

^a CITY UNIVERSITY OF HONG KONG   (Hong Kong)

Author keywords

[No Author keywords available]

Indexed keywords

ALUMINA; BINDERS; COMPOSITION EFFECTS; CRACK PROPAGATION; CRYSTAL WHISKERS; DEGRADATION; DIFFUSION IN SOLIDS; HEATING; OXIDATION; SILICON CARBIDE; THERMAL EFFECTS; THERMOGRAVIMETRIC ANALYSIS;

BINDER REMOVAL ANALYSIS;

CERAMIC MATRIX COMPOSITES;

ANALYSIS; COMPOSITES, FIBRE-REINFORCED;

EID: 0031138461     PISSN: 02638223     EISSN: None     Source Type: Journal    
DOI: 10.1016/S0263-8223(97)00083-4     Document Type: Article

References (14)

1. Edirisinghe, M.J. and Evans, J.R.G., Review: fabrication of engineering ceramics by injection moulding - I. Materials selection. Int. J. High Tech. Ceram., 1986, 2, 1-31.
2. Edirisinghe, M.J. and Evans, J.R.G., Review: fabrication of engineering ceramics by injection moulding - II. Techniques. Int. J. High Tech. Ceram., 1986, 2, 249-278.
3. Sakai, T., State of the art injection molding of high-performance ceramics. Advances in Polymer T Technology, 11 (1) (1991/1992) 53-67.
4. Edirisinghe, M.J., Fabrication of engineering ceramics by injection moulding. Ceram. Bull., 1991, 70, (5), 824-828.
5. 4 composites. J. Mat. Sci. Letter, 1987, 6, 1356-1358.
6. Stedman, S.J., Evans, J.R.G. and Woodthorpe, J., Whisker length degradation during the preparation of composite ceramic injection moulding suspensions. J. Mat. Sci., 1990, 25, 1025-1032.
7. Stedman, S.J., Evans, J.R.G. and Woodthorpe, J., Rheology of composite ceramic injection moulding suspensions. J. Mat. Sci., 1990, 25, 1833-1841.
8. Tsao, I. and Danforth, S.C., Rheological behavior of injection-moldable silicon powder-silicon carbide whisker formulations. J. Am. Ceram. Soc., 1993, 76, (12), 2977-2984.
9. Woodthorpe, J., Edirisinghe, M.J. and Evans, J.R.G., Properties of ceramic injection moulding formulations Part 3 Polymer removal. J. Mat. Sci., 1989, 24, 1038-1048.
10. Shukla, V.N. and Hill, D.C., Binder evolution from powder compacts: thermal profile for injection molded articles. J. Am. Ceram. Soc., 1989, 72, (10), 1797-1803.
11. Pinwill, I.E., Edirisinghe, M.J. and Bevis, M.J., Development of temperature-heating rate diagrams for the pyrolytic removal of binder used for powder injection moulding. J. Mat. Sci., 1992, 27, 4381-4388.
12. Edirisinghe, M.J., Binder removal from moulded ceramic bodies in different atmospheres. J. Mat. Sci. Lett., 1991, 10, 1338-1341.
13. Evans, J.R.G. and Edirisinghe, M.J., Interfacial factors affecting the incidence of defects in ceramic mouldings. J. Mat. Sci., 1991, 26, 2081-2088.
14. w composite. J. Mat. Proc. Tech., 1997, 63, (1-3), 399-404.