Mechanisms of ambient temperature fatigue crack growth in Ti-46.5Al-3Nb-2Cr-0.2W

Metallurgical and Materials Transactions A: Physical Metallurgy and Materials Science

Volumn 28, Issue 13, 1997, Pages 825-835

  Worth, B D ^a   Larsen, J M ^b   Balsone, S J ^b,c   Jones, J W ^d  

^a UNIVERSITY OF DAYTON   (United States)

^b AIR FORCE RESEARCH LABORATORY   (United States)

^c GENERAL ELECTRIC COMPANY   (United States)

^d UNIVERSITY OF MICHIGAN   (United States)

Author keywords

[No Author keywords available]

Indexed keywords

AMBIENT TEMPERATURES; CLOSURE MECHANISMS; CONSTANT LOADS; CRACK GROWTH; CRACK GROWTH BEHAVIOR; CRACK PATHS; CRACK-GROWTH RESISTANCE; CYCLIC FREQUENCY; DUPLEX MICROSTRUCTURES; EXTRINSIC MECHANISMS; FATIGUE CRACK GROWTH; FATIGUE CRACK GROWTH RATES; FATIGUE-CRACK-GROWTH TESTS; FRACTOGRAPHIC; FULLY LAMELLAR; INDUCED CRACK; LAMELLAR INTERFACES; LAMELLAR MICROSTRUCTURE; NOMINAL COMPOSITION; SECONDARY CRACKING; SERVOHYDRAULIC; STRESS RATIO; TEST METHOD; THRESHOLD STRESS INTENSITY FACTOR RANGE; TWO-PHASE ALLOYS;

ALUMINUM; CHROMIUM; COMPUTER CONTROL SYSTEMS; CRACK DETECTION; FATIGUE CRACK PROPAGATION; FATIGUE OF MATERIALS; LIGAMENTS; MICROSTRUCTURE; NIOBIUM; PHASE INTERFACES; COMPUTER AIDED ANALYSIS; CRACK PROPAGATION; FATIGUE TESTING; FRACTOGRAPHY; HEAT TREATMENT; MATHEMATICAL MODELS; METALLOGRAPHIC MICROSTRUCTURE; STRESS INTENSITY FACTORS;

CRACK CLOSURE; TITANIUM ALLOYS;

DUPLEX MICROSTRUCTURES; LAMELLAR MICROSTRUCTURES; SHEAR LIGAMENTS; TWO PHASE ALLOYS;

EID: 0031101851     PISSN: 10735623     EISSN: None     Source Type: Journal    
DOI: 10.1007/s11661-997-1010-9     Document Type: Article

References (37)

1. J.M. Larsen and T. Nicholas: Eng. Fract. Mech., 1985, vol.22, pp. 715-730
2. Y.-W. Kim: JOM, 1994, vol.46, pp. 30-40.
3. S.J. Balsone, J.M. Larsen, D.C. Maxwell, and J.W. Jones: Mater. Sci. Eng., 1995, vols. A192/A193, pp. 457-464
4. Fatigue and Fracture of Ordered Intermetallic Materials I, S.J. Balsone, J.W. Jones, D.C. Maxwell, T.S. Srivatsin, W. Sobayejo, and D.L. Davidsons, eds., TMS, Warrendale, PA, 1994.
5. FATIGUE '96, J.M. Larsen, B.D. Worth, S.J. Balsone, A.H. Rosenberger, J.W. Jones, G. Lutjering, and H. Nowacks, eds., Elsevier Science Ltd., Berlin, 1996, 3, 1719-1730.
6. Gamma Titanium Aluminides, J.M. Larsen, B.D. Worth, S.J. Balsone, J.W. Jones, R. Wagner M. Yamaguchi, and Y.-W. Kims, eds., TMS/ASM INTERNATIONAL, Warrendale, PA, 1995, 821-834.
7. J.M. Larsen, B.D. Worth, S.J. Balsone, and S.J. Rosenberger: 8th World Conf. on Titanium, The Institute of Materials, Birmingham, United Kingdom, 1995, in press.
8. K.T.V. Rao, Y.W. Kim, C.L. Muhlstein, and R.O. Ritchie: Mater. Sci. Eng., 1995, vols. A192/A193, pp. 474-482
9. Titanium '92: Science and Technology, A.W. James, P. Bowen, F.H. Froes, and I. Caplans, eds., TMS, Warrendale, PA, 1993, pp. 1139-1146
10. A.W. James, R.A. Chave, C.A. Hippsley, and P. Bowen: Proc. 3rd Eur. Conf. on Advanced Materials and Processes. Part I (of 3), J. Phys., 1993, vol.3, pp. 411-421
11. P. Bowen, R.A. Chave, and A.W. James: Mater. Sci. Eng., 1995, vols. A192/A193, pp. 443-456
12. W.O. Sobayejao, J.E. Deffeyes, and P.B. Aswath: Mater. Sci. Eng., 1991, vol.A138, pp. 95-101.
13. W.O. Soboyejo and C. Mercer: Scripta Metall. Mater., 1994, vol.30, pp. 1515-1520
14. D.L. Davidson, J.B. Campbell, and R.A. Page: Metall. Trans. A, 1991, vol.22A, pp. 377-391
15. D.L. Davidson: Materials Research Society Symposia Proceedings, Materials Research Society, Pittsburgh, PA, 1992, vol.273, pp. 67-80.
16. D.L. Davidson and J.V. Campbell: Metall. Trans. A, 1993, vol.24A, pp. 1555-1574
17. Proc. 1st Int. Symp. on Structural Intermetallics, K.S. Chan, D.L. Davidson, J.J. Lewandowski, R. Darolia, C.T. Liu, P.L. Martin, D.B. Miracle, and M.V. Nathals, eds., TMS, Warrendale, PA, 1993, pp. 223-230.
18. K.S. Chan: Metall. Trans. A, 1993, vol.24A, pp. 569-583
19. K.S. Chan and Y.-W. Kim: Metall. Mater. Trans. A, 1994, vol.25A, pp. 1217-1228
20. K.S. Chan and Y.-W. Kim: Acta Metall. Mater., 1995, vol.43, pp. 439-451
21. K.S. Chan: Metall. Mater. Trans. A, 1995, vol.26A, pp. 1407-1418
22. K.T.V. Rao, G.R. Odette, and R.O. Ritchie: Acta Metall. Mater., 1992, vol.40, pp. 353-361
23. K.T.V. Rao, G.R. Odette, and R.O. Ritchie: Acta Metall. Mater., 1994, vol.42, pp. 893-911.
24. Standard Test Method for Measurement of Fatigue Crack Growth Rates, ASTM E 647-95, ASTM, Philadelphia, PA, 1995, pp. 578-614.
25. J.M. Larsen, J.R. Jira, and S.R. Ravichandran: Measurement of Small Cracks by Photomicroscopy: Experiments and Analysis, J.M. Larsen and J.E. Allison, eds., ASTM, Philadelphia, PA, 1992, pp. 57-80.
26. S.J. Balsone, B.D. Worth, J.M. Larsen, and J.W. Jones: Scripta Metall. Mater., 1995, vol.32, pp. 1653-1658
27. A.W. James and P. Bowen: Processing Properties and Applications of Metallic and Ceramic Materials, Engineering Materials Advisory Services, Ltd., U.K., 1992, vol.2, pp. 677-682
28. R.O. Ritchie: Mater. Sci. Eng. A, 1988, vol.A103, pp. 15-28.
29. Small Fatigue Cracks, R.O. Ritchie, W. Yu, and J. Lankfords, eds., TMS, Warrendale, PA, 1986, pp. 167-189.
30. L.P. Zawada and T. Nicholas: The Effect of Closure on the Near-Threshold Fatigue Crack Propagation Rates of a Nickel Base Superalloy, Newman, J.C., Jr. and W. Elber, eds., ASTM, Philadelphia, PA, 1988, pp. 548-567
31. S. Banerjee: A Review of Crack Closure, AFWAL-TR-84-4031, AFWAL/MLLN, Wright-Patterson Air Force Base, OH, 1984.
32. S. Suresh: Metall. Trans. A, 1983, vol.14A, pp. 2375-2385
33. S. Suresh: Metall. Trans. A, 1985, vol.16A, pp. 249-260
34. Mechanics of Materials, F.P. Beer and E.R. Johnston, Jr., eds., McGraw-Hill, Inc., New York, NY, 1992.
35. R.O. Ritchie, Y. Weikang, and R.J. Bucci: Eng. Fract. Mech., 1989, vol.32, pp. 361-377
36. Y.-W. Kim: Mater. Sci. Eng. A, 1995, vols. A192/A193, pp. 519-533
37. J.C. Newman: Behavior of Short Cracks in Airframe Components, NATO AGARD, Toronto, 1982, vol.328, pp. 6.1-6.26.