메뉴 건너뛰기




Volumn 37, Issue 2, 1997, Pages 201-213

Prediction of the limiting drawing ratio and the maximum drawing load in cup-drawing

Author keywords

[No Author keywords available]

Indexed keywords

ANISOTROPY; FORECASTING; LOADS (FORCES); NUMERICAL METHODS; PARAMETER ESTIMATION; PLASTIC FLOW; SHEET METAL; STRAIN HARDENING;

EID: 0031075659     PISSN: 08906955     EISSN: None     Source Type: Journal    
DOI: 10.1016/0890-6955(95)00107-7     Document Type: Article
Times cited : (67)

References (17)
  • 1
    • 0002496296 scopus 로고
    • The importance of directionality in drawing quality sheet steel
    • R.L. Whiteley, The importance of directionality in drawing quality sheet steel, Trans. ASM 52, 154 (1960).
    • (1960) Trans. ASM , vol.52 , pp. 154
    • Whiteley, R.L.1
  • 2
    • 85143725437 scopus 로고
    • Studies of plastic flow of anisotropic metals
    • L.W. Hu, Studies of plastic flow of anisotropic metals, Trans. ASME, J. Appl Mech. 23, 444 (1956).
    • (1956) Trans. ASME, J. Appl Mech. , vol.23 , pp. 444
    • Hu, L.W.1
  • 3
    • 0010215939 scopus 로고
    • An investigation into the effect of plastic anisotropy and rate of work-hardening in deep drawing
    • L. Lilet and M. Wybo, An investigation into the effect of plastic anisotropy and rate of work-hardening in deep drawing, Sheet Metal Industries 41, 783 (1964).
    • (1964) Sheet Metal Industries , vol.41 , pp. 783
    • Lilet, L.1    Wybo, M.2
  • 4
    • 0001356256 scopus 로고
    • Assessing normal anisotropic plasticity of sheet metals
    • M. Atkinson, Assessing normal anisotropic plasticity of sheet metals, Sheet Metal Industries 44, 167 (1967).
    • (1967) Sheet Metal Industries , vol.44 , pp. 167
    • Atkinson, M.1
  • 5
    • 0015586586 scopus 로고
    • Sheet drawability assessed from a two-blank cup-drawing test and tensile test
    • J.M. Thorp, Sheet drawability assessed from a two-blank cup-drawing test and tensile test, Sheet Metal Industries 50, 99 (1973).
    • (1973) Sheet Metal Industries , vol.50 , pp. 99
    • Thorp, J.M.1
  • 8
    • 0039733375 scopus 로고
    • Effects of R-value on the deep-drawing of sheet metals
    • Y. Yamada, Effects of R-value on the deep-drawing of sheet metals, J. Japan Soc. Technol. plast. 5, 183 (1964).
    • (1964) J. Japan Soc. Technol. Plast. , vol.5 , pp. 183
    • Yamada, Y.1
  • 10
    • 0039681951 scopus 로고
    • The effect of anisotropy on instability in sheet metal forming
    • G. G. Moore and J. F. Wallace, The effect of anisotropy on instability in sheet metal forming, J. Inst. Metals 93, 33 (1964-1965).
    • (1964) J. Inst. Metals , vol.93 , pp. 33
    • Moore, G.G.1    Wallace, J.F.2
  • 11
    • 84996158224 scopus 로고
    • The effect of anisotropy and work-hardening characteristics on the stress and strain distribution in deep drawing
    • D.C. Chiang and S. Kobayashi, The effect of anisotropy and work-hardening characteristics on the stress and strain distribution in deep drawing, Trans. ASME, J. Engng. Ind. 88, 443 (1966).
    • (1966) Trans. ASME, J. Engng. Ind. , vol.88 , pp. 443
    • Chiang, D.C.1    Kobayashi, S.2
  • 13
    • 0015399845 scopus 로고
    • Plastic instability conditions in the deep-drawing of a circular blank of sheet metal
    • M.G. El-Sebaie and P.B. Mellor, Plastic instability conditions in the deep-drawing of a circular blank of sheet metal, Int. J. Mech. Sci. 14, 535 (1972).
    • (1972) Int. J. Mech. Sci. , vol.14 , pp. 535
    • El-Sebaie, M.G.1    Mellor, P.B.2
  • 14
    • 0043201057 scopus 로고
    • The effect of anisotropy and work hardening on cup drawing, redrawing and ironing
    • S. S. Hecker, A. K. Ghosh and H. L. Gegel (eds.), TMS-AIME, New York
    • W. F. Hosford, The effect of anisotropy and work hardening on cup drawing, redrawing and ironing, in Formability: Analysis, Modeling and Experimentation, S. S. Hecker, A. K. Ghosh and H. L. Gegel (eds.), TMS-AIME, New York, 78 (1977).
    • (1977) Formability: Analysis, Modeling and Experimentation , pp. 78
    • Hosford, W.F.1
  • 16
    • 0037658017 scopus 로고
    • On the complete solution of the deep-drawing problem
    • D.M. Woo, On the complete solution of the deep-drawing problem, Int. J. Mech, Sci. 10, 83 (1968).
    • (1968) Int. J. Mech, Sci. , vol.10 , pp. 83
    • Woo, D.M.1
  • 17
    • 0020087899 scopus 로고
    • Drawing force in deep drawing of cylindrical cup with flat-nosed punch
    • A.S. Korhonen, Drawing force in deep drawing of cylindrical cup with flat-nosed punch, Trans. ASME, J. Engng. Ind. 104, 29 (1982).
    • (1982) Trans. ASME, J. Engng. Ind. , vol.104 , pp. 29
    • Korhonen, A.S.1


* 이 정보는 Elsevier사의 SCOPUS DB에서 KISTI가 분석하여 추출한 것입니다.