Macro-level Optimization of Cutting Tool Geometry

Journal of Manufacturing Science and Engineering, Transactions of the ASME

Volumn 119, Issue 1, 1997, Pages 1-9

  Kaldor, S ^a   Venuvinod, P K ^a  

^a CITY UNIVERSITY OF HONG KONG   (Hong Kong)

Author keywords

[No Author keywords available]

Indexed keywords

CALCULATIONS; GEOMETRY; MACHINING; MATHEMATICAL MODELS; OPTIMIZATION;

CUTTING TOOL ANGLES; MACROLEVEL OPTIMIZATION;

CUTTING TOOLS;

EID: 0031069676     PISSN: 10871357     EISSN: 15288935     Source Type: Journal    
DOI: 10.1115/1.2836551     Document Type: Article

References (18)

1. Shaw, M. C., “Fracture of Metal Cutting Tools,” Annals CIRP, Vol. 28, No. l, p. 12, 1979.
2. Lau, W. S., and Rubenstein, C., “The Influence of the Plan Approach Angle in Orthogonal Cutting,” Int. J. Mach. Tool Des. Res., Vol. 22, No. 1, pp. 65-74, 1982.
3. Venuvinod, P. K., Lau, W. S., and Rubenstein, C., “The Estimation of the Dependence of Tool Life on Rake Angle Using Computed Flank Temperatures,” Proc. 5th Int. Conf. Procln Eng., Tokyo, p. 191, 1984.
4. Venuvinod, P. K., Lau, W. S., and Rubenstein, C., “Tool Life in Oblique Cutting as a Function of Computed Flank Temperature,” ASME Journal of Engineering for Industry, Vol. 112, p. 307, 1990.
5. Geometry of the Active Part of Cutting Tools-Part I: General Terms, Reference Systems, Tool & Working Angles, Chip Breakers,” ISO 3002/1, ISO publication, 1982.
6. Kaldor, S., and Lenz, E., “Drill Point Geometry and Optimization,” ASME Journal of Engineering for Industry, Vol. 104, Feb. 1982.
7. Kaldor, S., Trendler, P. H. H., and Hodgson, T., “Investigations Into the Clearance Geometry of End Mills,” Annals CIRP, Vol. 33/1, p. 33, 1984.
8. Kaldor, S., Trendler, P. H. H., and Hodgson, T., “Investigations and optimization of the Clearance Geometry of End Mills,” Annals CIRP, Vol. 34, No. 1, p. 149, 1985.
9. Kronenberg, M., Machining Science and Application, Pergamon Press, 1966.
10. Kaldor, S., “A Common Denominator for Optimum Cutting Tool Geometry,” Annals CIRP, Vol. 35, No. 1, p. 41, 1986.
11. Kaldor, S., and Ber, A., “A Criterion to Optimize Cutting Tool Geometry,” Annals CIRP, Vol. 39, No. 1, p. 53, 1990.
12. Kaldor, S., “Tool Life as Function of the Cutting Edge Inclination,” Internal Report of the Department of Manufacturing Engineering, City Polytechnic of Hong Kong, 1993.
13. Ber, A., and Kaldor, S., “The First Seconds of Cutting, Wear Behavior,” Annals CIRP, Vol. 31/1, p. 13, 1982.
14. Cemented Carbide as Tool and Design Material,” Sandvik Coromont, Sweden, publication E-5758, Feb. 1967.
15. Roark, R. J., et al., Formulas for Stress and Strain, McGraw-Hill, 1975.
16. Lord, H. W., et al., Noise Control for Engineers, R. Krieger Pub., 1987.
17. Kaldor, S., and Ber, A., “Tool Geometry Optimization,” Internal Report of the Ulman Centre for Manufacturing Research, Technion, Haifa, November, 1991.
18. Lenz, E., Moskovitz, D., Mayer, J., and Stauffer, D., “Optimal Edge Geometry for Maximum Tool Life,” ASME Publication 77-WA/Prod-43, 1977.