Thermohydrodynamic analysis of submerged oil journal bearings considering surface roughness effects

Journal of Tribology

Volumn 119, Issue 1, 1997, Pages 100-106

  Ramesh, J ^a,b   Majumdar, B C ^a   Rao, N S ^a  

^a INDIAN INSTITUTE OF TECHNOLOGY   (India)

^b Computervision R and D ^*  (India)

Author keywords

[No Author keywords available]

Indexed keywords

BEARINGS-JOURNAL; LUBRICANTS-OILS; SURFACE ROUGHNESS;

EID: 0030889674     PISSN: 07424787     EISSN: 15288897     Source Type: Journal    
DOI: 10.1115/1.2832442     Document Type: Article

References (19)

1. Christensen, H., and Tonder, K., 1973, “The Hydrodynamic Lubrication of Rough Journal Bearings,” ASME Journal of Lubrication Technology, Vol. 95, pp. 166-171.
2. Dowson, D., 1962, “A Generalized Reynolds Equation for Fluid Film Lubrication,” Int. J. Mech. ScL, Vol. 4, pp. 159-170.
3. Elrod, H. G., 1979, “A General Theory of Laminar Lubrication With Reynolds Roughness,” ASME Journal of Lubrication Technology, Vol. 101, 1979, pp. 8-14.
4. Ezzat, H., and Rhode, S., 1974, “Thermal Transients in Finite Slider Bearings,” ASME Journal of Lubrication Technology, Vol. 96, pp. 315-320.
5. Ferron, J., Frene, J., and Boncompain, R., 1983, “A Study of the Thermohydrodynamic Performance of a Plain Journal Bearing-Comparison Between Theory and Experiments,” ASME Journal of Lubrication Technology, Vol. 105, pp. 422-428.
6. Greenwood, J. A., and Tripp, J. H., 1970-71, “The Contact of Two Nominally Flat Rough Surfaces,” Proc. Inst. Mech. Engg., Vol. 185, pp. 625-633.
7. Jacobsson, B., and Floberg, L., 1965, “The Finite Journal Bearing, Considering Vaporization,” Trans. Chalmers Univ. Technol., Gothenburg.
8. Jang, J. Y., Cheng, M. J., and Lin, J. F., 1991, “Adiabatic Solutions of Finite Width Journal Bearings With Rough Surfaces,” Tribology Int., Vol. 24, pp. 373-380.
9. Kicinski, J., 1987, “Influence of the Flow Pre-history in the Cavitation Zone on the Dynamic Characteristics of Slide Bearings,” Wear, Vol. III, pp. 289-311.
10. Majumdar, B. C., 1975, “The Thermohydrodynamic Solution of Oil Journal Bearings,” Wear, Vol. 31, pp. 287-294.
11. Majumdar, B. C., and Hamrock, B. J., 1981, “Surface Roughness Effects on Finite Oil Journal Bearings,” NASA Tech. Memo. 82639.
12. McCallion, H., Yousif, F., and Lloyd, T., 1970, “The Analysis of Thermal Effects in a Full Journal Bearing,” ASME Journal of Lubrication Technology, Vol. 92, pp. 578-585.
13. Nayak, P. R., 1971, “Random Process Model of Rough Surfaces,” ASME Journal of Lubrication Technology, Vol. 93, pp. 398.
14. Ott, H. H., and Paradissiadis, G., 1988, “Thermohydrodynamic Analysis of Journal Bearings Considering Cavitation and Reverse Flow,” ASME Journal of Tribology, Vol. 110, pp. 439-447.
15. Patir, N., and Cheng, H. S., 1979, “Application of Average Flow Model to Lubrication Between Rough Sliding Surfaces,” ASME Journal of Lubrication Technology, Vol. 101, pp. 220-230.
16. Ritchmeyer, R. D., 1957, Difference Methods for Initial Value Problems, Interscience, New York, pp. 101.
17. Teale, J. L., and Lebeck, A. O., 1980, “An Evaluation of the Average Flow Model for Surface Roughness Effects in Lubrication,” ASME Journal of Lubrication Technology, Vol. 102, pp. 360-367.
18. Whitehouse, D. J., and Archard, J. F., 1970, “The Properties of Random Surfaces of Significance in their Contact,” Proc. R. Soc., London, Vol. A316, pp. 97-121.
19. Boncompain, R., Fillon, M., and Frene, J., 1986, “Analysis of Thermal Effects in Hydrodynamic Bearings,” ASME Journal of Tribology, Vol. 108, pp. 219-224.