Role of strain-hardening laws in the prediction of forming limit curves

Journal of Materials Processing Technology

Volumn 63, Issue 1-3, 1997, Pages 105-110

  Sing, W M ^a   Rao, K P ^a  

^a CITY UNIVERSITY OF HONG KONG   (Hong Kong)

Author keywords

Forming limits; Modelling; Sheet metal forming; Strain hardening laws

Indexed keywords

FORMABILITY; MATHEMATICAL MODELS; SHEET METAL; STRAIN; STRAIN HARDENING; STRESSES; THERMAL EFFECTS;

FORMING LIMIT CURVES; HILLS YIELD CRITERION; HOLLOMON EQUATION; PLASTIC NECKING REGION; SHEET METAL FORMING; STRAIN HARDENING LAW; STRESS STRAIN RELATIONSHIPS; SWIFT EQUATION; VOCE EQUATION;

METAL FORMING;

EID: 0030819782     PISSN: 09240136     EISSN: None     Source Type: Journal    
DOI: 10.1016/S0924-0136(96)02608-8     Document Type: Article

References (30)

1. R. Hill, On discontinuous plastic states, with special reference to localized necking in thin sheets, J. Mech. Phys. Solids, 1 (1952) 19-30.
2. H.W. Swift, Plastic instability under plane stress, J. Mech. Phys. Solids, 1 (1952) 1-18.
3. Z.H. Lu and D. Lee, Prediction of history-dependent forming limits by applying different hardening models. Int. J. Mech. Sci., 29 (1986) 123-137.
4. W.M. Sing and K.P. Rao, Prediction of sheet-metal formability using tensile-test results, J. Mat. Proc. Tech., 37 (1993) 37-51.
5. J. Gronostajski, Sheet metal forming-limit for complex strain paths, J. Mech. Work. Tech., 10 (1984) 349-362.
6. R. Arrieux, Determination and use of the forming limit stress diagrams in sheet metal forming, J. Mat Proc. Tech., 53 (1995) 47-56.
7. S.L. Semiatin and J.J. Jonas, Formability and workability of metals, ASM, Metals Park, Ohio, 1984.
8. H.J. Kleemola and J.O. Kumpulainen, A comparison of the formability of aluminium and steel sheets, Sheet Metal Ind., 64 (1978) 703-713.
9. J. Woodthorpe and R. Pearce, The effect of r and n upon the forming limit diagrams of sheet steel. Sheet Metal Ind., 55 (1969) 1061-1067.
10. H.J. Kleemola and A.J. Ranta-Eskola, Comparison of the strain-hardening parameters of sheet metals in uniaxial and biaxial tension, Metall. Trans. A, 7A (1976) 595-599.
11. Eugene Shapiro and Frank N. Mandigo, Forming limit analysis for enhanced fabrication, Int. Copper Research Assoc., Olin Metals Research Laboratory, N.Y., (1983) p.30-129.
12. R.H. Wagoner, Plastic behavior of 70/30 brass sheet, Metall. Trans. A, 13A (1982) 1491-1500.
13. R. Pearce, Some aspects of anisotropic plasticity in sheet metals, Int. J. Mech. Sci., 10 (1968) 995-1005.
14. M.I. Yousif, J.L. Duncan, and W. Johnson, Plastic deformation and failure of thin elliptical diaphragms. Int. J. Mech. Sci., 12 (1970) 959-972.
15. A.W. Bowen and P.G. Partridge, Limitations of the Hollomon strain-hardening equation, J. Phys. D: Appl. Phys., 7 (1974) 969-978.
16. M.F. Vieira and J.V. Fernandes, Plastic behaviour of copper sheets subjected to a double strain-path change, J. Mat. Proc. Tech., 47 (1995) 261-272.
17. M.G. Stout and K.P Staudhammer, Biaxial deformation of 70-30 brass: Flow behaviors, Texture, Microstructures, Metall. Trans. A, 15A (1984) 1607-1612.
18. A.K. Ghosh, The influence of strain hardening and strain rate sensitivity on sheet metal forming, Trans. ASME, J. Eng. Mats. and Tech., 99 (1977) 264-274.
19. K. Saka, The uniaxial strain-hardening behaviour of sheet metal from zero strain to failure, J. Mech. Work Tech., 3 (1979) 17-30.
20. E. Bayraktar, C. Levaillant and S. Altintas, Formability characterization of Hadfield steel, J. Mat. Proc. Tech., 47 (1994) 13-31.
21. A.K. Ghosh and W.A. Backofen, Strain hardening and instability in biaxially stretched sheets, Metall. Trans., 4 (1973) 1113-1123
22. E.W. Hart, Theory of the tensile test, Acta Metallurgica, 15 (1967) 351-355.
23. F. Garofalo and J.R. Low Jr., The effect of prestraining in simple tension and biaxial tension on flow and fracture behaviour of a low carbon deep-drawing steel sheet, J. Mech. Phys. Solids, 3 (1955) 275-294.
24. M.J. Painter and R. Pearce, Instability and fracture in sheet metal, J. Phys. D: Appl. Phys., 7 (1974) 992-1002.
25. H.J. Kleemola and M.A. Nieminen, On the strain-hardening parameters of metals, Metall. Trans., 5 (1974) 1863-1866.
26. R. Hill, Theoretical plasticity of textured aggregates, Math. Proc. Camb. Phil. Soc., 85 (1979) 179-191.
27. W.M. Sing and K.P. Rao, Influence of material properties on sheet metal formability limits, J. Mat. Proc Tech., 48 (1995) 35-41.
28. H.J. Kleemola and M.T. Pelkkikangas, Effect of predeformation and strain path on the forming limits of steel, copper and brass, Sheet Metal Ind., 63 (1977) 591-599.
29. R.H. Wagoner and N.M. Wang, Operant strain-rate sensitivity during tensile necking, Metall. Trans. A, 14A (1983) 2395-2460.
30. R.D. Jenkins and D.V. Wilson, The characterization of stretch-forming behaviour by measurement of uniform elongation in the tensile test, Sheet Metal Ind., 48 (1971) 21-38.